neUxtlight Adapt Pro Series ser Manual
- June 6, 2024
- nextlight
Table of Contents
USER MANUAL
Thank you for choosing
WARNING: Please read and follow the instructions before installing and using your NextLight Adapt Pro.
NextLight Adapt Pro
The NextLight Adapt Pro integrates NextLight Pro-Series fixtures with most third-party 0-10V Controllers.
- 5 Year Full Warranty
Please scan the QR code to access our online product listing for the NextLight Adapt Pro. There you can access more info, digital versions of this User Manual, Spec Sheets and more! If you still have questions, please call 513.718.7556 or email sales@nextlight.com
https://nextlight.com/index.php?route=product/product&product_id=150
Package Contents
-
NextLight Adapt Pro x1
-
12V AC/DC Adapter x1
-
0-10V Wirenut Converter x1
see 5. Adapt Using Wirenut Converter -
NextLight Pro Series Control Cable (20′) x1
Connections
- DC Input
- 0-10V Input
- Power Indicator
- Signal Indicator
- 485 Output
*Dust cap removed to show port
Product Installation
- The NextLight Adapt Pro can be mounted to the wall using two nails/screws and mounting holes (3 3/8” apart) on the back of the controller.
- Insert 12V AC/DC Adapter into DC Input and plug into a power source.
- Insert an RJ12 cable into the 0-10V Input of the NextLight Adapt Pro and connect the other end to the input of the third party 0-10V controller.
- Remove the dust cap from 485 Output of NextLight Adapt Pro.
- Insert NextLight Pro Series Control Cable into 485 Output of the adapter. Then screw the locking ring clockwise to ensure proper connection.
- Insert another end of Control Cable into Dim In connection on Driver of the first Fixture in lighting system chain.
- Connect Control Cable from Dim Out on Driver of the first Fixture to Dim In on Driver of next Fixture in the lighting system chain.
- Repeat until all Drivers/Fixtures are connected.
- To ensure proper dimming control, make sure Onboard Dimmer on Driver is set to EXT ( External Contro l). Not applicable to all NextLight Pro-Series fixtures.
Adapt Using Wirenut Converter
Some third-party 0-10V controllers may use bare wires for a 0-10V connection with the lighting system. In this case, use the supplied 0-10V Wirenut Converter as seen below.
- Insert 12V AC/DC Adapter into DC Input and plug into a power source.
- Insert Wirenut Converter into 0-10V Input of the NextLight Adapt Pro and connect the bare wires from 0-10V connection to the Wirenut Converter.
- Remove the dust cap from 485 Output of NextLight Adapt Pro.
- screw the locking ring clockwise to ensure proper connection.
- Insert another end of Control Cable into Dim In connection on Driver of the first Fixture in lighting system chain.
- Connect Control Cable from Dim Out on Driver of the first Fixture to Dim In on Driver of next Fixture in the lighting system chain.
- Repeat until all Drivers/Fixtures are connected.
- To ensure proper dimming control, make sure Onboard Dimmer on Driver is set to EXT (External Control). Not applicable to all NextLight Pro-Series fixtures.
Safety Recommendations and Warnings
WARNING: Please read and follow all Safety Recommendations and Warnings before installing your NextLight Adapt Pro.
- Please check and adhere to all local rules, regulations, and zoning codes when installing.
- The installer is responsible for the correct and safe installation of the light system.
- Do NOT hang the Adapter by Power Cord.
- Only use Power Cords that were supplied with your Adapter.
- Do NOT use the Adapter with a damaged Power Cord.
- Do NOT attempt to open, rewire or reconfigure any components of the Adapter. It will void the warranty and could cause serious injury or death.
- Always disconnect power from the Adapter before moving or cleaning it.
- Do NOT clean the Adapter with detergents, abrasives, or other aggressive substances.
- Do NOT use the Adapter near flammable, explosive, or reactive substances.
- Keep the Adapter away from excessive heat, water, dust, and contamination.
- Do NOT use any Volatile Organic Compounds (VOCs) on or near the Adapter. VOCs can cause damage to the components (including insect foggers).
- If the surface of the NextLight Adapt Pro is dirty, wipe it with a dry towel.
NextLight Support
Please scan the QR code to access our online Support page, which includes the User Manual, FAQ, and additional Warranty Claim information. nextlight.com/support
https://nextlight.com/index.php?route=information/information&information_id=47
Five (5) Year Full Manufacturer’s Warranty
All NextLight products carry a Five (5) Year Full Manufacturer’s Warranty from the date of purchase. Please follow all instructions and guidelines to ensure the warranty is not voided. This warranty does not apply to any product which has been damaged, defaced, subjected to misuse, abnormal service or handling (including shipping damage), or which has been altered in design or construction.
WILLVOLD WARRANTY
To file a Warranty Claim, visit nextlight.com/warranty
**** This product is for horticulture use only. Not suitable for room illumination.
Legal Disclaimer
NextLight products are to be used for lawful purposes only. It is the
responsibility of you as the purchaser to know and abide by all laws
pertaining to the use of NextLight
products. NextLight, LLC will NOT be held liable for any unlawful state or
federal activity arising out of the use of our products. By purchasing a
NextLight product, you are agreeing to these terms and conditions, confirming
that you as the purchaser are attesting to the lawful use of our product and
are thereby solely responsible for acting in conformance with all applicable
regulations.
Thank you for choosing
Questions about your NextLight Pro Series products?
513.718.7556
sales@nextlight.com
©2021 NextLight. All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>