JEFFREY ALEXANDER MIR2CAD-24-BS Rectangular Framed Beveled Edge Bathroom Vanity Wall Mirror Instruction Manual
- June 13, 2024
- JEFFREY ALEXANDER
Table of Contents
JEFFREY ALEXANDER MIR2CAD-24-BS Rectangular Framed Beveled Edge Bathroom
Vanity Wall Mirror
Product Information
The product is a vanity top with an undermount bowl. It is recommended to handle the product with care to avoid breakage, chipping, or injury. If unsure about assembling and installing the vanity top and bowl, it is recommended to seek professional installation.
Product Usage Instructions
- Prepare:
- Carefully place the vanity top polished side down on a soft smooth surface to prevent scratching or scuffing.
- Clean the underside of the vanity top with a damp towel to remove any debris for a secure seal to the bowl.
- Allow the vanity top to dry before proceeding to Step 2.
- Draw a Template:
- Place the bowl on the exposed surface of the vanity top and center it between the anchor holes.
- Situate the bowl so that the overflow hole faces the front of the vanity top (opposite from the plumbing holes).
- Using a pencil, trace around the entire edge of the bowl.
- Once the template is completed, carefully remove the bowl.
- Apply Silicone: Apply a generous bead of Bath & Tile silicone around the entire template between the drawn line and the bowl cutout.
- Attach Brackets:
- Place brackets over the anchor holes in the vanity top and tighten with the provided screws.
- Situate the bowl so that the overflow hole faces the front of the vanity top (opposite from the plumbing holes).
- Final Silicone Application:
- Allow the silicone to dry according to the silicone manufacturer’s instructions.
- Once the silicone is dry, apply another bead of silicone around the outer edge of the bowl where it meets the vanity top to create a seal and prevent excess moisture.
- Wipe away excess silicone to create a smooth seal.
- Allow additional silicone to dry according to the silicone manufacturer’s instructions.
- Attach the assembled top & bowl to the vanity base:
- Apply a generous bead of silicone around the entire top edge of the vanity base.
- Carefully place the top onto the vanity base, ensuring that the back of the vanity top is flush with the back of the vanity.
- Allow the silicone to dry according to the silicone manufacturer’s instructions.
- Move the vanity to its final location against the wall.
- Install the Backsplash:
- Clean the underside of the backsplash thoroughly to remove any debris for a secure hold to the vanity.
- Apply a generous amount of silicone to the unfinished back of the backsplash.
- Carefully align the backsplash to the vanity top, then firmly secure it in place against the vanity top and wall.
- Allow the silicone to dry according to the silicone manufacturer’s instructions.
- Once the vanity and backsplash are in the final location, add a final bead of silicone around the edge of the backsplash and wall for a secure seal. Smooth the silicone for a finished look.
TOOLS & SUPPLIES NEEDED
- Bath & Tile Silicone Sealant
- Screwdriver
- Pencil
INSTALLATION
- Prepare
- a. Carefully place the vanity top POLISHED side down on a soft smooth surface to prevent scratching or scuffing.
- b. Clean the underside of the vanity top with a damp towel to remove any debris to ensure a secure seal to the bowl.
- c. Allow time for the vanity top to dry before proceeding to Step 2.
- Draw a Template
- a. Place the bowl on the exposed surface of the vanity top and center it between the anchor holes.
- b. Situate the bowl so that the overflow hole is facing the front of the vanity top (opposite from the plumbing holes).
- c. Using the pencil, trace around the entire edge of the bowl.
- d. Once the template is completed, carefully remove the bowl.
- Apply Silicone
- a. Apply a generous bead of Bath & Tile silicone around the entire template between the drawn line and the bowl cutout.
- b. Carefully and quickly place bowl back onto the vanity top using the drawn template as a guide.
- c. Again, situate the bowl so that the overflow hole is facing the front of the vanity top (opposite from the plumbing holes).
- Attach Brackets
- a. Place brackets over the anchor holes in the vanity top and tighten with the provided screws.
- Note: Hardware Resources vanity bowls include anchor kits and screws. These Jeffrey Alexander vanity tops are pre-anchored and will not require the additional set of anchor pieces. Only the brackets and screws will be used.
- Final Silicone Application
- a. Allow time for silicone to dry, following silicone manufacturer instructions.
- b. Once the silicone is dry, apply another bead of silicone around the outer edge of the bowl where it meets the vanity top. This will help prevent excess moisture by creating a seal.
- c. Wipe away excess silicone to create a smooth seal.
- d. Allow time for additional silicone to dry, following silicone manufacturer instructions.
- Attach the assembled top & bowl to the vanity base
- a. Apply a generous bead of silicone around the entire top edge of the vanity base.
- b. Carefully place the top onto the vanity base.
- i. The back of the vanity top should be flush with the back of the vanity.
- ii. Situate the vanity top so that there is equal overhang on each side of the vanity (approximately ½” on either side).
- c. Allow time for silicone to dry, following silicone manufacturer instructions.
- d. Move the vanity to it’s final location against the wall.
- Install the Backsplash
- a. Clean the underside of the backsplash thoroughly to remove any debris to ensure a secure hold to the vanity.
- b. Apply a generous amount of silicone to the unfinished back of the backsplash.
- c. Apply a ¼” bead of silicone to the vanity top where the backsplash will be placed.
- d. Carefully align the backsplash to the vanity top, then firmly secure it in place against the vanity top and wall.
- e. Allow time for silicone to dry, following silicone manufacturer instructions.
- f. Once the vanity and backsplash are situated in the final location, add, add a final bead of silicone around the edge of the backsplash and wall for a secure seal. Smooth the silicone for a finished look.
- **Install the Sidesplash***
- a. Clean the underside of the sidesplash thoroughly to ensure a secure hold to the vanity.
- b. Apply a generous amount of silicone to the unfinished back of the sidesplash.
- c. Apply a ¼” bead of silicone to the vanity top where the side splash will be placed.
- d. Carefully align the sideplash to the vanity top, then firmly secure it in place against the vanity top and wall.
- e. Allow time for silicone to dry, following silicone manufacturer instructions.
- f. Once the sidesplash is situated, add a final bead of silicone around the edge of the backsplash and wall for a secure seal. Smooth the silicone for a finished look.
Sidesplash is sold separately.
Hardware Resources is not responsible for any error, damage, or injuries from
the installation process as a result of possible printing errors in
instructions.
CAUTION: Risk of personal injury. Handle with care. The product can
break, chip, or cause injury if mishandled.
NOTE: If you are unsure of assembling and installing the vanity top and
bowl, Hardware Resources recommends that you seek an installation
professional.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>