Honeywell TC09PEU Portable Evaporative Air Cooler User Manual

Honeywell TC09PEU Portable Evaporative Air Cooler

Product Information

Product Usage Instructions

Control Panel
The control panel consists of three icons:

• I: Power
• II: Cool
• III: Swing

The icons represent the following functions:

• Power: Press this button to turn the unit on. The cooler will start automatically at medium speed. After a few seconds, the speed will switch to low. Press the button again to turn the unit off.
• Cool: Before operating the unit in Cool mode, make sure to add water. Press this button until it is illuminated on the display screen. The water pump will operate, and you will feel cooler air after the Honeycomb Cooling Media is completely wet.
• Speed: Press the SPEED button repeatedly to change the speed between Low, Medium, and High.
• Swing: Press the SWING button until it is illuminated on the display. The louvers will begin to move left to right automatically. You can manually adjust the louvers to change vertical air flow.

Remote Control
The remote control provides the following functions:

• Power: Turns the unit on/off.
• Speed: Adjusts the speed between Low, Medium, and High.
• Cool: Controls the evaporative cooling function.
• Swing: Controls the motion of the louvers.

Note: Keep batteries away from children to avoid the risk of chemical burns.

Cooler Location
Before setting up and using the product, ensure that you position the air cooler correctly. Refer to the “COOLER LOCATION” section in the separate Safety & Maintenance Guide for detailed instructions.

Filling with Water
Caution: Always unplug the unit from the electrical socket before emptying or refilling the water tank.

To fill the water tank:

1. Open the Water Fill Door located on the back of the unit.
2. Manually refill the water tank when the water level is low. Do not fill water above the Max. water level mark to avoid water droplets collecting on the louvers.
3. Check the water level in the tank before running the COOL function. Ensure that the water in the tank is above the minimum water level mark. Running the unit in COOL mode with inadequate water may cause pump failure.

Note: The water capacity mentioned refers to the total volume of water that can be contained within the air cooler water tank and water distribution system. The water capacity in the tank at the Max. indicator level may be lower than the actual water capacity of the air cooler.

Customer Support:
Web: www.jmatek.com
USA: 1-800-474-2147 | usinfo@jmatek.com
CANADA^: 1-888-209-0999 | canadainfo@jmatek.com
^ Canada Customer Support service available for models sold in Canada only.

PARTS DESCRIPTION

1. Control Panel
2. Louvers
3. Water Level Indicator
4. Casters
5. Water Fill Door
6. Drain Plug
7. Side Grill
8. Honeycomb Cooling Media
9. Power Cord & Plug

WARNING — READ AND SAVE THE AIR COOLER SAFETY & MAINTENANCE GUIDE AND USER MANUAL BEFORE USING THIS PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY DAMAGE AND/ OR IMPAIR ITS OPERATION AND VOID THE WARRANTY. IN CASE THERE IS ANY INCONSISTENCY OR CONFLICT BETWEEN THE ENGLISH VERSION AND ANY OTHER LANGUAGE VERSION OF THE CONTENT OF THIS MATERIAL, THE ENGLISH VERSION SHALL PREVAIL.

USE & OPERATION

CONTROL PANEL

Icons on Control Panel

• Power
• Cool
• Swing
• Speed
• = Low
• = Medium
• • = High

FUNCTION BUTTONS

POWER
Press the button to turn the unit on. The cooler will start automatically at medium speed. After a few seconds the speed will switch to low. To turn the unit off, press the button again.

COOL
You must add water before operating the unit in Cool mode. Press the button until is illuminated on the display screen. The water pump will operate and you will feel the cooler air after the Honeycomb Cooling Media is completely wet.

SPEED
Press the SPEED button repeatedly to change the speed between   – – .

SWING
Press the SWING button until is illuminated on the display. The louvers will begin to move left to right automatically. You can manually adjust the louvers to change vertical air flow.

REMOTE CONTROL

• POWER : ON / OFF
• SPEED: Low / Medium / High
• COOL: Evaporative Cooling ON / OFF
• SWING: Controls the motion of the louvers

NOTE:

• The remote control requires a CR2025 (1 x 3V) coin type or equivalent battery for replacement. Open the battery compartment at the back of the remote control and insert the battery inside. Care must be taken to insert the batteries according to the correct polarity (+ / –) markings shown inside the battery compartment.
• Always point the remote control signal transmitter towards the unit when operating. Make sure that the signal path is not obstructed.
• Remove the batteries if the unit is not going to be used for an extended period of time.
• Do not drop the remote control.
• Do not mix different types of batteries such as alkaline, carbon-zinc, or rechargeable batteries. Do not mix old and new batteries.
• Do not recharge the battery.
• Exhausted batteries are to be removed from the product and safely disposed of as per local regulations.
• Do not dispose of batteries in fire. Batteries may explode or leak.
• This product contains a lithium button/coin cell battery. If a new or used lithium button/ coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
• The batteries shall be disposed of properly, including keeping them away from children.
• Even used batteries may cause injury.
  WARNING: Chemical Burn Hazard. Keep batteries away from children.

COOLER LOCATION
Make sure to position the air cooler correctly before you set up and start using the product. Please refer to the COOLER LOCATION section of the separate Safety & Maintenance Guide.

FILLING WITH WATERCAUTION:
Unplug the unit from the electrical socket before emptying or refilling the water tank.
Open the Water Fill Door located on the back of the unit.

Manual Tank Refilling:
The Water Level Indicator is located at the front of the unit. Refill the water tank when water level is low. Do not fill water above the “Max.” water level mark to avoid water droplets collecting on the louvers. Check the water level in the tank before running the COOL function. Make sure that the water in the tank is above the minimum water level mark. Running the unit in COOL mode with inadequate water may cause pump failure.

Note: The water capacity refers to the total volume of water that can be contained within the air cooler water tank and water distribution system. The water capacity in the tank at the “Max.” indicator level may be lower than the actual water capacity of the air cooler.

WARNING: Do not fill water tank with dirty water or salt water. This can damage the unit and Honeycomb media.

LOW WATER ALARM
The unit is equipped with a low water sensor. In Cooling Mode, when water in the tank is below the minimum level, you will hear a beeping sound and the GREEN LED will flash continuously. The unit will automatically pause evaporative cooling.
Refill the water tank to deactivate the alarm in cooling mode. First switch OFF the unit and unplug from the power outlet. Fill the water tank with water above the minimum water level mark. Plug in and switch ON again.
To deactivate the alarm and continue using the unit as a fan (without evaporative cooling), switch the unit OFF and then ON again. The Low Water Alarm will not activate in Fan only mode. The Low Water Alarm will sound again if the COOL function is activated while the water tank is still empty.

CLEANING & DRAINING THE WATER TANK
Below are instructions on how to clean and maintain your air cooler. If the cooler will not be used for a long period of time, please refer to the STORAGE & MAINTENANCE GUIDELINES located in the separate Safety & Maintenance Guide.

WARNING:
Before cleaning the unit, power OFF the unit and disconnect from the electrical socket.

• Move the unit to a location where the water can be drained. Remove the cap from the drain plug located at the bottom of the unit. Allow the tank to empty.
• Refill the water tank with clean water, up to the maximum level and drain it completely.
• Use a damp cloth to remove the dirt and dust from the surface of the unit. Never use corrosive elements or chemicals to clean this product.
• When the product is not in use, store the unit in a dry place out of direct sunlight.

CLEANING THE HONEYCOMB COOLING MEDIA
WARNING:
Before cleaning the unit, switch the unit OFF and disconnect the power adapter from the unit and electrical socket.

• The appliance is supplied with a Honeycomb Cooling Media.
• The Honeycomb Cooling Media are located inside the Side Grill. See Figure 1 for instructions on how to remove them from the unit for cleaning and maintenance.
• Do not run the unit in COOL mode with stale water in the tank. You must empty the water tank and refill with fresh water, especially if the tank has not been cleaned in a long time.
• The cleaning frequency for the Honeycomb media depends on local air and water conditions. In areas where the mineral content of water is high, mineral deposits may build up on the Honeycomb Cooling Media and restrict air flow. Draining the water tank and refilling with fresh water at least once a week will help reduce mineral deposits. If mineral deposits remain on the Honeycomb Cooling Media, the media should be removed and washed under fresh water. The media should be cleaned every two months or sooner, depending on your needs.
• For best results allow the Honeycomb Cooling Media to dry after each use by turning off the cool function 15 minutes before turning the unit off.

Removing the Honeycomb Cooling Media:

• Remove all the screws from the side grill of the Air Cooler, carefully pull out the side grill from the cooler. Rinse the side grill with clean water and let it dry before re-installing to the unit.
• Carefully pull out the Honeycomb Media from the unit.
• Replace or clean media with water and a damp cloth as needed.
• WARNING: DO NOT operate the Air Cooler when the side Grill is removed from the Air Cooler, or if there is a loose-fitting side Grill. Doing so can cause serious injury or dangerous electrical shock.

Made in China
© 2019 JMATEK Limited. All rights reserved.
The Honeywell Trademark is used under license from Honeywell International Inc.
Honeywell International Inc. makes no representations or warranties with respect to this product.
This product is manufactured by Airtek Int’l Corp. Ltd. (subsidiary of JMATEK Ltd.).

JMATEK North America LLC
Mahwah, New Jersey 07495 USA
Email: usinfo@jmatek.com
Web: www.jmatek.com

References

• Home - JMATEK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>