FIAMMA F65L LED Strip Awning Kit Instruction Manual
- June 6, 2024
- FIAMMA
Table of Contents
FIAMMA F65L LED Strip Awning Kit
COMFORT – Tech
Check that nothing has been damaged or deformed during transport.
In the event of doubts or questions concerning the installation, use, or
limitations of the product, contact the dealer. We recommend that the
installation is carried out by qualified personnel and in compliance with
current local regulations.
F65L 018 – only FRONT BAR
After cutting the LED strip it is advisable to tape with insulating tape the end of the strip on the cut side, otherwise, the resistance to water and moisture will be lost.
F80s – FRONT BAR
After cutting the LED strip it is advisable to tape with insulating tape the end of the strip on the cut side, otherwise, the resistance to water and moisture will be lost.
F80s – CASE
After cutting the LED strip it is advisable to tape with insulating tape the end of the strip on the cut side, otherwise, the resistance to water and moisture will be lost.
In case of problems please contact your local dealer
INSTALLATION
Read the following instructions and warnings carefully; failure to observe
these installation and usage instructions as well as the laws for driving in
the relevant country may cause severe harm or damage for which the
manufacturer declines all responsibility.
The product has been designed and manufactured exclusively for the
illumination of recreational vehicles, is not suitable for the illumination of
home environments.
For safety reasons, it is advisable to always disconnect the negative terminal
from the batteries on the vehicle and then work without power during
installation.
It is suggested to connect the power cable to the fuse box or to the terminal
board and not directly to the battery.
Use the correct fuse for connection to the vehicle power supply according to
EN 1648-1 and EN 1648-2.
Installing an oversized fuse can cause overheating which can result in a short
circuit or malfunction of the entire electrical equipment.
Choose the safest and shortest installation for the power cable. Reduce the
length of the power cable as necessary.
Use only cable clamps suitable for the diameter of the power cable for
connection to the terminal board.
If incorrect terminals are used, this could cause a voltage drop and increase
the formation of heat on the terminal.
It is strictly forbidden to go around with the LED lights on; connect the
power supply in order to inhibit current fl ow while the vehicle is running.
We do not recommend prolonged periods of viewing at close proximity of the LED
strip. The manufacturer will not be held responsible for claims for damages
resulting from the following:
- Defective installation or connection of the product.
- Damage to the product is caused by mechanical infl uences and overvoltage.
- Alterations on the device without the express authorization of the manufacturer.
EU Declaration of Conformity (DoC)
- Company name: Fiamma S.p.A.
- Postal address: Via San Rocco, 56
- Postcode and city: Cardano al Campo – (Varese)
- Telephone number: 0311/709111
- E-mail address: fiamma@fiamma.it
**Declare that the DoC is issued under our sole responsibility and
belongs to the following product:**
- Apparatus model / Product: Lighting systems
- Trademark: Fiamma
Model / Type:
- 98655-850 Rafter Led
- 98655-902 Rafter Led Caravanstore
- 98655-914 Led Awning Case
- 98655-915 Kit Led Awning Case 50
- 98655-848 Led Awning Light
- 98655-883 Led Garage Light
- 98655A884 Led Sensor Door Light
- 98655-607 Led Awning Light Gutter
- 98655-849 Awning Arms Led
- 98655-886 Led Step
- 98655-471 Kit Awning Led
- 98655Z040 Kit Led Strip Awning
- 98655Z051 Kit Led Strip Awning High Brightness
- 98655-885 Led Warning Solar
- 98655Z098 Kit Led F65 Eagle
- 98655Z099 Kit Led F45 Eagle
**The object of the declaration described above is in conformity with
the relevant Union harmonization legislation:**
- 2014/30/EU Electro Magnetic Compatibility Directive (EMCD).
- 2014/35/EU Low Voltage Directive (LVD).
- 2011/65/EU Restriction of the use of certain hazardous substances Directive (RoHS Directive).
- 2012/1194EU Implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for directional lamps, light emitting diode lamps and related equipment.
- 2012/874/EU Supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to energy labelling of electrical lamps and luminaires.
- EN 60529 (1991) + A1 (2000) The IP code or Ingress Protection ratings are defined in international standard (IP grade 44)
- IEC 62471:2006 Photobiological safety of lamps and lamp systems.
Warranty Fiamma
In case of defects with regards to materials and manufacturing, the customer is entitled to the warranty in accordance with local laws and regulations of the country in which the product was purchased.fiamma.com