midocean F0028114 GPS Tracker User Manual
- June 6, 2024
- midocean
Table of Contents
midocean F0028114 GPS Tracker
- Frequency Range; GSM/GPRS 900: Tx: 880-915MHz, GSM/GPRS 1800: Tx: 1710-1785MHz, Rx: 1805-1880 MHz, GPS: 1.57GHz.
- Maximum radio-frequency power; GSM900: 32.63dBm, GSM1800: 29.63dBm
(2014/53/EU art. 10-9 Simplified Declaration of Conformity) Hereby, MOB, declares that item MO8734 complies with the essential requirements and other relevant conditions of directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.momanual.com MOB, PO BOX 644, 6710 BP (NL).
GPS tracker Accessories:
- 1 X Device
- 1 X USB charge cable
- 1 X User Guide
Hardware Specification:
- Hardware Specification: Mainframe Dimension 86556mm
- Net weight 40g
- GSM frequencies 850/900/1800/1900Mhz
- GPRS Class12, TCP/IP
- GPS chip UBLOX G7020
- Voltage range 3.6-4.2VDC
- Standby Current ≤2mAh
- GPS locating time Cold start 38s
- GPS Accuracy Warm start 32s
- GPS sensitivity Hot start=2s
- Work environment temperature ≤ 10m
- Work environment humidity – 159DB – 40℃+80℃ 20%-80%RH
- Battery Chargeable 3.7v 1000mAh
SIM Card Installation:
- Micro SIM card ( 12*15mm)
- Insert the SIM card in the SIM card slot
- The SIM card chip inserted towards the side without the SOS button
- The SIM card is not included in the package, Any SIM card which support GSM 2G can work and be available from the user’s local operator.
- Before installing the SIM card, please check if the SIM card has a PIN code or not, if yes, please use a cell-phone to unlock the card’s PIN code. In addition, make sure it is activated and has sufficient credit on it.
Device Charging:
For the first time of use, please fully charge the battery for around 2-3 hours with the USB charger.
Turn on the device by Inserting Card
Please insert the SIM card in the correct direction. You will see the
indicator light blinks, then turns off. This means the SIM card has been
inserted successfully.
Led indicator:
- Solid blue: SIM card inserted incorrectly
- Flashing blue: Searching for GPS signal
- Blue off: Is working correctly
- Red on: Charging the battery
- Red off: Fully charged
Configuration and Operation by SMS
To Set the authorized Number
Command: CENTER,000000,phone number#
NOTE : The letters or symbols should be English and the letters should be
in capital.
Example : CENTER,000000,123456789#
- Using your mobile phone, send the above command to the phone number of the device, it will reply: Center OK!
- To delete this number, you can send :CENTER,000000,0# to the phone number of the device.
GPRS Setting
In order to use the GPRS function, the user needs to setup the APN by sending
an SMS command. What is APN? Access Point name (APN) is the name used to
identify a general packet radio service (GPRS) bearer service in the GSM
mobile network. The APN defines the type of service that is provided in the
packet data connection.
- Make sure that the SIM card in the tracker supports the GPRS function.
- The APN can be acquired from your local GSM operators.
Command: APN, APN information, user name, password#
Note : Some APN are without user name and password, so please leave it
blank.
For example APN, internet, 123,456# (with the user name and password)
APN, internet# (without the user name and password)
- please set it up when the device cannot connect with the web platform or the APP.
- After sending the command, it will reply: APN OK!
Location request
Reply with coordinates and web link Command:URL# The device will reply: the
map link, the longitude and latitude
Example:http://maps.google.com/maps?q=N22.669534,E114.011888
Click on the link then the location can be shown directly on Google Map on
your mobile phone.
Vibration Alarm
Command : VA, ON# (turn on this function)VA, OFF# (turn off this
function)
- Please move the device after 5minutes,then you will get a message reply: vibration alarm, please note!
- This function is off by default setting.
- After sending the command, it will reply: VA OK!
Over-Speed Alert
Command : OS, 80# (80 is the set-up speed) OS, OFF# (turn off this
function)
- This is to turn on/off the over-speed alarm, speed unit:km/h
- Speed range:30-180km
- This function is off by default setting.
- After sending the command, it will reply: OS OK!
Listen-in (Voice Monitoring)
Command : JT# (turn on the function) JT0# (turn off the function)
Please call the mobile number in the device, then you can hear what is
happening around the tracker after you get the SMS reply when turning on this
function.
SOS Alarm
Command : SK, 1# (Alarm on) SK, 0#(Alarm off)
- Press the SOS button for 3 seconds, it will call the authorized number.
- After the first operation, please wait at least 3minutes to test again, otherwise it will not work.
Checking Settings
Command:QP#
- The device will reply : IMEI:3568XXXXXXXXX90
- APN: cmnet
- IP:b.gps903.net/7700
- LMT, 0#
- CENTER:
- SOC4 ：1
Reboot device
Command :RESET#
The device will restart itself without changing any settings.
Initialization
Command:RFS#
- This is to restore all settings back to the factory default, except the IP.
- Only the authorized number has the right to operate.
- Please use with caution
How to Connect Device to the Platform for real time tracking via GPR
- Check through PC
- Web Platform : www.gps903.net (International)
- Account: Device IMEI (shown on the back of the device cover))
- Original passwords: 123456
- Operations of APP in a Cellular Phone
- APP NAME: GPSONE
- please search for it in the IOS app store or Google play store or scan the QR code from the web platform
- please login the app as following:
Geo-fence
An electronic fence can be set up after login APP or PC. Then you can check the messages from the device messages.
Cautions:
Please comply with the instructions to extend the life of the device
- Do not use & store the unit in dusty places.
- Do not put expose the unit to extremes in temperature hot or cold.
- Clear the unit with a piece of dry cloth. Do not clean in chemicals or detergent.
- Do not disassemble the unit.
- Do not change the battery in the unit as this can cause damage.