FIAMMA 98655-850 Rafter LED Lighting Kit Instruction Manual
- June 6, 2024
- FIAMMA
Table of Contents
FIAMMA 98655-850 Rafter LED Lighting Kit
Package contents
Installation instructions
Check that nothing has been damaged or deformed during transport. In the event of doubts or questions concerning the installation, use or limitations of the product, contact the dealer. We recommend that the installation is carried out by qualifi ed personnel and in compliance with current local regulations.
OPTION 1
**OPTION 2
** Put the electrical terminals (max. 12 Volt) in the point where the rafter-
led will be installed. The ideal position is the central area of the awning,
putting it beside the fi xing kit for rafter (if already existing).
Consult our website for spare parts drawing.
Safety instructions
Read the following instructions and warnings carefully; failure to observe
these installation and usage instructions as well as the laws for driving in
the relevant country may cause severe harm or damage for which the
manufacturer declines all responsibility. The product has been designed and
manufactured exclusively for the illumination of recreational vehicles, is not
suitable for the illumination of home environments. For safety reasons, it is
advisable to always disconnect the negative terminal from the batteries on the
vehicle and then work without power during installation. It is suggested to
connect the power cable to the fuse box or to the terminal board and not
directly to the battery. Use the correct fuse for connection to the vehicle
power supply according to EN 1648-1 and EN 1648-2. Installing an oversized
fuse can cause overheating which can result in a short circuit or malfunction
of the entire electrical equipment. Choose the safest and shortest
installation for the power cable. Reduce the length of the power cable as
necessary.
Use only cable clamps suitable for the diameter of the power cable for
connection to the terminal board. If incorrect terminals are used, this could
cause a voltage drop and increase the formation of heat on the terminal. It is
strictly forbidden to go around with the LED lights on; connect the power
supply in order to inhibit current fl ow while the vehicle is running. We do
not recommend prolonged periods of viewing at close proximity of the LED
strip. The manufacturer will not be held responsible for claims for damages
resulting from the following:
- Defective installation or connection of the product.
- Damage to the product caused by mechanical infl uences and overvoltage.
- Alterations on the device without the express authorization of the manufacturer.
Warranty
In case of defects with regards to materials and manufacturing, the customer is entitled to the warranty in accordance with local laws and regulations of the country in which the product was purchased.
EU Declaration of Conformity (DoC)
- Company name: Fiamma S.p.A.
- Postal address: Via San Rocco, 56
- Postcode and city: Cardano al Campo – (Varese)
- Telephone number: 0311/709111
- E-mail address: fiamma@fiamma.it
Declare that the DoC is issued under our sole responsibility and belongs to the following product:
- Apparatus model / Product: Lighting systems
- Trademark: Fiamma
Model / Type:
- 98655-850 Rafter Led
- 98655-902 Rafter Led Caravanstore
- 98655-914 Led Awning Case
- 98655-915 Kit Led Awning Case 50
- 98655-848 Led Awning Light
- 98655-883 Led Garage Light
- 98655A884 Led Sensor Door Light
- 98655-607 Led Awning Light Gutter
- 98655-849 Awning Arms Led
- 98655-886 Led Step
- 98655-471 Kit Awning Led
- 98655Z040 Kit Led Strip Awning
- 98655Z051 Kit Led Strip Awning High Brightness
- 98655-885 Led Warning Solar
- 98655Z098 Kit Led F65 Eagle
- 98655Z099 Kit Led F45 Eagle
The object of the declaration described above is in conformity with the relevant Union harmonization legislation:
- 2014/30/EU Electro Magnetic Compatibility Directive (EMCD).
- 2014/35/EU Low Voltage Directive (LVD).
- 2011/65/EU Restriction of the use of certain hazardous substances Directive (RoHS Directive).
- 2012/1194EU Implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for directional lamps, light-emitting diode lamps and related equipment.
- 2012/874/EU Supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to energy labeling of electrical lamps and luminaires.
- EN 60529 (1991) + A1 (2000) The IP code or Ingress Protection ratings are defined in an international standard (IP grade 44)
- IEC 62471:2006 Photobiological safety of lamps and lamp systems.
The following harmonized standards and/or technical specifications have been applied
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>