Asteria Technology Pte GML001Z Gravio CO2 Sensor User Manual
- June 6, 2024
- Asteria Technology Pte
Table of Contents
Technology Pte GML001Z Gravio CO2 Sensor
User Manual
- Gravio Matrix Led sensor is a product that can display 16 by 16-pixel pictures and animations technology. It transmits pictures based on Zigbee wireless transmission technology, and at the same time, uses an stm32 microcontroller to display pictures and animations.
- Gravio Matrix Led has this very simple appearance. It has only 3 buttons, which are matching buttons, screen switches, and gravity-sensing toggle switches.
Front
Pair Button
Toggle switch and screen switch
Toggle Switches
When you use the Gravio matrix led, you can control whether the matrix uses gravity sensing to rotate the picture by flipping the switch. When the flipping switch is on the right, the gravity sensing is turned on. At this time, when you rotate the Gravio matrix led, the picture will be Follow the rotation, always facing up; when the toggle switch is on the left, the gravity sensor is turned off, no matter how you rotate the Gravio matrix led, the picture will not rotate
screen Switches
screen the switch can control the screen switch.
Pair button
When you need to wirelessly transmit pictures to Gravio matrix led, you need to add it to the Zigbee gateway network now. When the gateway is allowed to access the network, press and hold the pair button for 5 seconds, and the Zigbee icon on the screen will flash. At this time, it will be added to the network of your gateway soon. After joining the network, the flashing Zigbee picture will be displayed. Prohibited, at this time you can transfer pictures or animations through the host computer
Network access steps: (for example we use Gravio Receiver2)
Insert Gravio receiver into pc, Mac, or Linux, open serial debugging tools,
such as sscom
Typed hex：00 00 03 00 00 AA （build a network）
Go on：00 00 10 00 01 FF AA （Allow devices to connect to the network）
At this time, press and hold the button of Gravio matrix led for 5 seconds
until the Zigbee icon will flash
When a gateway receives network access information,
reply:|
---|---
When Gravio Matrix led is not normal, you can press and hold the button for 5 seconds to enter the matching network access state
send a picture
You need to copy the mac address of Gravio Matrix Led in the textbox at the
bottom（mac address text box）， and click save
And you can choose an rgb （click open rgb file） file from the host computer
and click send ，and few seconds it is will show on Gravio Matrix Led‘s screen
send text animations
In （please input text box）you can text less than 64bytes English alphabet and send to Gravio Matrix Led to show on the screen, you only need to type the alphabet in the text box and click send.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm the radiator your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>