Miele CS-7101 SmartLine Gas Wok Burner Instruction Manual
- June 6, 2024
- Miele
Table of Contents
Work in progress
CS-7101 SmartLine Gas Wok Burner
Operating and installation instructions SmartLine gas wok burner
To prevent the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time.
en-AU, NZ
M.-Nr. 11 503 510
This appliance can be used in countries other than those specified on the
appliance and in these operating and installation instructions. It is,
however, set up for connection to the gas and electricity supplies in the
countries specified. For trouble-free operation of the appliance, it is best
to use it in the countries specified for use. For use in other countries,
please contact Miele in your country.
2
Contents
Warning and Safety instructions……………………………………………………………. 5 Caring for the
environment …………………………………………………………………… 16
Overview………………………………………………………………………………………………. 17 Wok burner
……………………………………………………………………………………………. 17 Control
knobs………………………………………………………………………………………… 18
Burner…………………………………………………………………………………………………… 19 Accessories supplied
……………………………………………………………………………… 20 Before using for the first time
……………………………………………………………….. 21 Cleaning the SmartLine appliance for the first
time …………………………………….. 21 Switching on the SmartLine appliance for the first
time ………………………………. 21 Suitable cookware………………………………………………………………………………… 22 Tips
on saving energy ………………………………………………………………………….. 24
Operation……………………………………………………………………………………………… 25 Switching
on………………………………………………………………………………………….. 25
FlameGuard…………………………………………………………………………………………… 25 Adjusting the
flame…………………………………………………………………………………. 26 Switching
off………………………………………………………………………………………….. 26 Safety
features……………………………………………………………………………………… 27 Thermo-electric flame failure
device …………………………………………………………. 27 Cleaning and care
………………………………………………………………………………… 28 Cleaning the ceramic
surface…………………………………………………………………… 29 Cleaning the control knob(s)
……………………………………………………………………. 30 Cleaning the pan supports
………………………………………………………………………. 30 Cleaning the burner(s)
…………………………………………………………………………….. 31 Assembling the
burner(s)…………………………………………………………………………. 32 Problem solving guide
………………………………………………………………………….. 33 Optional accessories
……………………………………………………………………………. 35
Service…………………………………………………………………………………………………. 36 Contact in case of fault
…………………………………………………………………………… 36 Data plate
……………………………………………………………………………………………… 36 Warranty
……………………………………………………………………………………………….. 36
Installation……………………………………………………………………………………………. 37 Safety instructions for
installation …………………………………………………………….. 37 Safety
distances…………………………………………………………………………………….. 39
3
Contents
Detailed dimensions ……………………………………………………………………………….. 42 Installation notes
surface-mounted ………………………………………………………… 43 Worktop cut-out surface-
mounted…………………………………………………………. 45 Spacer bars surface-
mounted……………………………………………………………….. 48 Installation dimensions Surface-mounted
……………………………………………….. 49 Installation surface-
mounted…………………………………………………………………. 51 Installation notes flush-fit
……………………………………………………………………… 53 Worktop cut-out flush-fit
………………………………………………………………………. 55 Spacer bars flush-fit
…………………………………………………………………………….. 58 Installation dimensions Flush-fit
…………………………………………………………….. 59 Installation flush-fit
………………………………………………………………………………. 61 Gas connection
……………………………………………………………………………………… 63 Burner ratings
………………………………………………………………………………………… 66 Electrical connection
………………………………………………………………………………. 67 Conversion to another type of gas
………………………………………………………… 68 Jet table………………………………………………………………………………………………… 68
Changing the jets …………………………………………………………………………………… 68
Changing the main jets……………………………………………………………………….. 69 Changing the small jets
………………………………………………………………………. 69 Checking operation
………………………………………………………………………………… 70
4
Warning and Safety instructions
This wok complies with all current local and national safety requirements.
However, inappropriate use can lead to personal injury and damage to property.
Read the operating and installation instructions carefully before using the
wok. They contain important information on safety, installation, use and
maintenance of the appliance. This prevents both personal injury and damage to
the appliance. In accordance with standard IEC 60335-1, Miele expressly and
strongly advises that you read and follow the instructions in “Installation”
and in “Warning and Safety instructions”. Miele cannot be held liable for
injury or damage caused by noncompliance with these instructions. Keep these
instructions in a safe place and pass them on to any future owner.
5
Warning and Safety instructions Correct application This wok burner is
designed for domestic use and for use in
similar environments by guests in hotel or motel rooms, bed & breakfasts and
other typical living quarters. This does not include common/shared facilities
or commercial facilities within hotels, motels or bed & breakfasts. The wok
burner is not suitable for outdoor use. It is intended only to cook food and
keep it warm. Any other use is not supported by Miele and could be dangerous.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
its use by a person responsible for their safety, and are able to recognise
the dangers of misuse.
6
Warning and Safety instructions Safety with children Young children must not
be allowed to use this appliance. Older children may only use the gas wok
burner if its operation
has been clearly explained to them and they are able to use it safely. They
must be aware of the potential dangers caused by incorrect operation. Cleaning
may only be carried out by older children under the supervision of an adult.
Please supervise children in the vicinity of the wok burner and do not let
them play with it. The appliance gets hot when in use and remains hot for a
while after being switched off. Keep children well away from the appliance
until it has cooled down and there is no danger of burning. Danger of burning!
Do not store anything which might arouse a child’s interest in storage areas
above or next to the wok burner. Otherwise children could be tempted to climb
onto the wok burner with the risk of burning themselves. Danger of burning and
scalding! Turn the handles of pots and pans on the cooktop to the side or the
rear so that children cannot pull them down and burn themselves. Danger of
suffocation! Whilst playing, children may become entangled in packaging
material (such as plastic wrapping) or pull it over their head with the risk
of suffocation. Keep packaging material away from children.
7
Warning and Safety instructions
Technical safety Unauthorised installation, maintenance and repairs (including
removal of any cover) can cause considerable danger for the user.
Installation, maintenance and repairs must only be carried out by a Miele
authorised technician. Damage to the wok burner can compromise your safety.
Check the appliance for visible signs of damage. Never use a damaged wok
burner. Temporary or permanent operation with a self-sufficient or nonmains
synchronous energy supply system (e.g. isolated networks, back-up systems) is
possible. A requirement for the operation is that the energy supply system
complies with all current local and national requirements that apply to stand-
alone, solar and/or battery systems. The protective measures provided in the
domestic installation and in this Miele product must also be assured in their
function and operation in isolated operation or in non-mains synchronous
operation, or replaced with equivalent measures in the installation. The
electrical safety of this appliance can only be guaranteed when continuity is
complete between it and an effective earthing system which complies with local
and national safety regulations. It is most important that this basic safety
requirement is present and tested regularly and, where there is any doubt, the
household wiring system should be inspected by a qualified electrician. Before
connecting the appliance to the mains electricity supply, ensure that the
connection data on the data plate (voltage and frequency) matches the mains
electricity supply. This data must correspond in order to avoid the risk of
damage to the appliance. Consult a qualified electrician if in any doubt. Do
not connect the appliance to the mains electricity supply by a multi-socket
adapter or an extension lead. These are a fire hazard and do not guarantee the
required safety of the appliance.
8
Warning and Safety instructions For safety reasons, this appliance may only be
used after it has
been built in. This appliance must not be installed and operated in mobile
installations (e.g. on a ship). Never open the casing of the wok burner.
Touching or tampering with electrical connections or components and mechanical
parts is highly dangerous to the user and can cause operational faults. The
manufacturer’s warranty will be invalidated if the appliance is not repaired
by a Miele authorised service technician. Faulty components must only be
replaced by genuine Miele spare parts. The manufacturer can only guarantee the
safety of the appliance when Miele replacement parts are used. The wok burner
is not intended for use with an external timer switch or a remote control
system. Connection to the gas supply must be carried out by a suitably
qualified and competent gas fitter. If the plug has been removed or the
connection cable is not supplied with a plug, the appliance must be connected
to the mains supply by a suitably qualified electrician. If the mains
connection cable is damaged, it must be replaced with a special mains
connection cable by a qualified and competent electrician in order to avoid a
hazard (see “Installation – Electrical connection”).
9
Warning and Safety instructions
During installation, maintenance and repair work, the wok burner must be
completely disconnected from the mains electricity supply. The gas supply must
also be turned off. It is only completely isolated from the gas and
electricity supply when: – the main circuit breaker has been disconnected, or
– it is switched off at the wall socket and the plug is withdrawn from
the socket. Do not pull the mains connection cable but the mains plug to
disconnect your appliance from the mains electricity supply. – the gas inlet
valve is closed. Danger of electric shock! Do not use the wok if it is faulty,
or if the ceramic surface is cracked, chipped or damaged in any way. Switch it
off immediately if any damage is noticed. Disconnect it from the mains
electricity and gas supply. Call Miele. If the wok burner is built in behind a
furniture front (e.g. a door), do not close the door while the wok burner is
in use. Heat and moisture can build up behind the closed door. This can result
in damage to the wok burner, the housing unit and the floor. Leave the
furniture door open until the wok burner has cooled down completely. In areas
which may be subject to infestation by cockroaches or other vermin, pay
particular attention to keeping the appliance and its surroundings clean at
all times. Any damage caused by cockroaches or other vermin will not be
covered by the warranty. DO NOT MODIFY THIS APPLIANCE. This cooktop is not
suitable for installation and operation with aftermarket lids or covers
fitted. Carry out an annual visual inspection of the gas lines and gas
appliances in your home. This inspection must comply with applicable national
regulations.
10
Warning and Safety instructions Correct use The appliance gets hot when in use
and remains hot for some
time after being switched off. Do not touch the appliance if there is a
possibility that it could still be hot. DO NOT USE THIS APPLIANCE AS A SPACE
HEATER. Due to the high temperatures radiated, objects left near the appliance
could catch fire. Oil and fat can overheat and catch fire. Do not leave the
wok burner unattended when cooking with oil and fat. If it does ignite, do not
attempt to put the flames out with water. Switch off the wok burner and use a
suitable fire blanket, saucepan lid, damp towel or similar to smother the
flames. The cooking process has to be supervised. A short term cooking process
has to be supervised continuously. Flames could set the grease filters of a
rangehood on fire. Do not flambé under a rangehood. DO NOT SPRAY AEROSOLS IN
THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION. DO NOT PLACE ARTICLES
ON OR AGAINST THIS APPLIANCE. Do not heat an empty pan. Do not heat up food in
closed containers e.g. tins or sealed jars on the wok burner, as pressure can
build up in the containers, causing them to explode. Do not cover the wok
burner, e.g. with a cooktop cover, a cloth or protective foil. The material
could catch fire, shatter or melt if the wok burner is switched on by mistake
or if residual heat is still present.
11
Warning and Safety instructions
When the wok burner is switched on, either deliberately or by mistake, or when
there is residual heat present, there is the risk of any metal items left on
the wok heating up, with the danger of burning. Depending on the material,
other items left on the appliance could also melt or catch fire. Do not use
the wok burner as a resting place. You could burn yourself on the hot
appliance. Protect your hands with heat-resistant pot holders or gloves when
handling hot pots and pans. Do not let them get wet or damp, as this causes
heat to transfer through the material more quickly with the risk of scalding
or burning yourself on steam. Be sure to keep all textiles away from the gas
flames. Do not use oversized cloths, tea towels or other similar materials.
When using an electrical appliance, e.g. a hand-held food mixer, near the wok
burner, ensure that the cable of the electrical appliance cannot come into
contact with the hot wok burner. The insulation on the cable could become
damaged. Even a light object can cause damage in certain circumstances. Do not
drop anything on the ceramic surface. Plastic and aluminium foil containers
melt at high temperatures. Do not use plastic or aluminium foil containers on
the cooktop. When a control knob is pressed down, a spark is generated on the
ignitor. Do not press down the control knob while you are cleaning or touching
the wok or the burner in the vicinity of an ignitor. If a rangehood is
installed above the wok burner, ensure that the burner is always covered with
a pan when in use. Otherwise flames could reach the rangehood, parts of which
could then be damaged or even set on fire. Switch the burner off when a pan is
removed, even for a short time.
12
Warning and Safety instructions
Make sure all the components of the gas burner have been correctly assembled
before switching on. Only use pans with a diameter that falls within the
minimum and maximum diameters given for the burner (see “Pans”). A pan which
is too small will be unstable on the pan support. If the diameter is too
large, heat emitted from the bottom of the pan may damage the worktop, walls
with poor heat resistance (e.g. panelled walls), or parts of the wok burner.
Miele cannot be held liable for this type of damage. Ensure that the flames
from the burner do not spread out beyond the base and up the sides of the pan.
Do not use pans with very thin bases. Failure to comply may result in damage
to the wok burner. The pan supports supplied with the appliance must always be
used. Never place a pan on the burner itself. Replace the pan supports
carefully to avoid scratching the surface of the cooktop. DO NOT USE OR STORE
FLAMMABLE MATERIALS IN THE APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE.
CUTLERY INSERTS MUST BE HEAT-RESISTANT. Remove all grease spatters and other
combustible (food) residues from the wok burner as soon as possible. They are
a fire hazard. The use of the wok burner creates heat, moisture and combustion
products in the room where it is installed. Make sure that the appliance is
installed in a location with sufficient ventilation. Natural ventilation
openings should not be blocked. Alternatively, a mechanical ventilation device
(e.g. a rangehood) can be installed. If the wok burner is used for very long
periods of time, additional ventilation of the room may be necessary, e.g. by
opening windows or doors, or running the rangehood on the highest setting.
13
Warning and Safety instructions If the appliance has not been used for a long
period of time it
should be thoroughly cleaned before it is used again. It is also advisable to
have the appliance tested by a qualified person for safety. If you are
operating a gas cooking appliance directly next to the downdraft extractor,
the FlameGuard must be placed between the downdraft extractor and the
appliance.
14
Warning and Safety instructions Cleaning and care Do not use a steam cleaning
appliance to clean this wok burner.
Pressurised steam could reach the electrical components and cause a short
circuit. Miele will guarantee to supply functional spare parts for a minimum
of 10 years and up to 15 years following the discontinuation of your SmartLine
appliance.
15
Caring for the environment
Disposal of the packing material
The transport and protective packaging has been selected from materials which
are environmentally friendly for disposal, and can normally be recycled.
Recycling the packaging reduces the use of raw materials in the manufacturing
process and also reduces the amount of waste in landfill sites. Ensure that
any plastic wrappings, bags etc. are disposed of safely and kept out of the
reach of babies and young children. Danger of suffocation.
Disposing of your old appliance
Electrical and electronic appliances often contain valuable materials. They
also contain specific materials, compounds and components, which were
essential for their correct function and safety. These could be hazardous to
human health and to the environment if disposed of with your domestic waste or
if handled incorrectly. Please do not, therefore, dispose of your old
appliance with your household waste.
Please dispose of it at your local community waste collection / recycling centre for electrical and electronic appliances. You are also responsible for deleting any personal data that may be stored on the appliance prior to disposal. Please ensure that your old appliance poses no risk to children while being stored prior to disposal.
16
Wok burner
a Wok burner b Pan supports c Control knobs
Overview
17
Overview
Control knobs
a Burner off The gas supply is turned off
b Strongest flame The outer and inner burners are on the highest setting
c Strong flame The outer burner is on the lowest setting, the inner burner on
the highest setting
d Over-ignition position The outer burner is ignited by changing from position
(5) to position (3) NB: Position (4) is a transitional setting. Continuous
operation of the burner is not recommended between positions (5) and (3).
e Weak flame The outer burner is off, the inner burner is on the highest
setting
f Weakest flame The outer burner is off, the inner burner is on the lowest
setting
18
Burner a b
c
d
e
f
a Outer burner cap b Inner burner cap c Burner head d Burner base e Thermo- electric flame failure device f Ignitor
Overview
19
Overview
Accessories supplied
The accessories supplied with your appliance, as well as a range of optional
ones, are available to order from Miele (see “Optional accessories”).
Wok ring The wok ring supplied gives additional stability to the wok, especially to woks with a rounded base.
Combination trivet
The combination trivet supplied must be used if you are using pans with a smaller base diameter than that specified in the chart for suitable pans. FlameGuard
For fitting in place between the downdraft extractor and a gas cooking appliance.
20
Before using for the first time
Please stick the extra data plate for the appliance supplied with this
documentation in the space provided in the “Service” section of this booklet.
Alternatively, the additional label can be stuck near the appliance if the
appliance markings are not visible after installation.
Remove any protective wrapping and stickers (except the data plate).
Cleaning the SmartLine appliance for the first time
Clean all removable parts of the burner(s) with a solution of warm water and a
small amount of washing-up liquid applied with a soft sponge. Dry all parts
thoroughly after cleaning and then reassemble the burners (see “Cleaning and
care Burners”).
Clean the ceramic surface with a damp cloth, and then wipe dry.
Switching on the SmartLine appliance for the first time
The metal components have a protective coating. Smells and possibly some
vapours may occur when the SmartLine appliance is used for the first time. The
smell and any vapours given off do not indicate a faulty connection or
appliance and they are not hazardous to health.
21
Suitable cookware
Minimum cookware base diameter [cm]
Pots/Pans
14
Maximum diameter at top of cookware [cm]
Pots/Pans
30
– Position the cookware centrally on the pan support so that it sits securely and cannot tip. There might still be slight movement, which is not a cause for concern.
– Refer to the chart above and ensure that the pan diameter falls within the
minimum and maximum diameters given for the burner you are using. Using
cookware that is too large can cause the flames to spread out and damage or
burn the worktop, wall claddings or surrounding units and also parts of the
cooktop or other appliances. Using pans of the correct size improves
efficiency. Any cookware that has a diameter smaller than the pan supports or
that does not rest safely (without wobbling) on the pan supports is dangerous
and should not be used.
– Remember when purchasing new pans that manufacturers usually refer to the
diameter at the top of the pan in their documentation.
– All heat-resistant cookware is suitable for use.
– Cookware with a thick base is preferable, as it distributes heat more
evenly. Cookware with a thin base may cause food to overheat in some places.
To avoid this, stir the food frequently.
– Always place cookware on the pan supports supplied with the appliance. Never
place it directly on the burners.
– Do not use pots or pans with base supports.
22
Wok ring
Use the wok ring to give additional stability to pans, especially to woks with
a rounded base.
Suitable cookware
Place the wok ring on the pan support so that it sits securely in position and
cannot move (see diagram).
Combination trivet
The combination trivet must be used if you wish to use a pot or pan with a
smaller diameter base than the minimum given in the table.
23
Tips on saving energy
– Use a pan lid whenever possible to minimise heat loss.
– Wide, shallow pans are preferable to tall, narrow ones. They will heat up
faster.
– Cook with as little water as possible. – Reduce the power setting once the
water has come to the boil or the oil is hot enough to fry in. – Use a
pressure cooker to reduce cooking times.
24
Operation
Switching on
If you are operating a gas cooking appliance next to a downdraft extractor,
this will affect the gas cooking appliance’s function. Place the FlameGuard
between the gas cooking appliance and the downdraft extractor.
Risk of fire due to overheated
food! Unattended food can overheat and ignite. Do not leave the wok unattended
whilst it is being used.
Switching on during a power outage If there is an interruption to the
electricity supply, the gas can be ignited manually, e.g. with a match. Press
down the relevant control knob
and turn it anti-clockwise to the large flame symbol. Hold the control knob
pressed down and light the gas at the burner with a match. Keep the control
knob pressed down for a further 5-10 seconds and then release it.
FlameGuard
Press in the relevant control knob and turn it anti-clockwise to the large flame symbol. The ignition electrode will “click” and ignite the gas.
When a control knob is activated, a spark is automatically generated on all
burners. This is normal and does not indicate a fault. When a flame is
visible, keep the
control knob pressed in for 5 10 seconds, and then let it go. If the burner
has not ignited or goes out, turn the control knob to the position. Aerate the
room or wait for at least one minute before trying again. Try keeping the
control knob pressed in for a little longer the next time. If the burner does
not ignite the second time, turn the control back to the position and see
“Problem solving guide”.
Fit the magnetic FlameGuard in position next to the downdraft extractor when you are operating a gas cooking appliance directly next to the extractor.
25
Operation
Adjusting the flame
As the outer part of the flame is much hotter than the centre, the tips of the
flames should stay beneath the pan base. Flame tips which extend beyond the
sides of the pan merely warm up the air in the room and can damage pan handles
and increase the risk of injury.
Switching off
Turn the control knob clockwise to the position.
This stops the flow of gas and extinguishes the flame.
There is a stopper at the 6 o’clock position to prevent you turning the
control knob to the high or low setting unintentionally. Press the control
knob down lightly to move past this stopper. Adjust the flame so that it does
not
spread out beyond the sides of the pan. To move from the high to the low
setting, turn the control anticlockwise until it stops. Then press it down and
continue to turn it past the resistance before releasing it. You can now
select the setting you require. To move from the low to the high setting, turn
the control clockwise until it stops. Then press it down and continue to turn
it past the resistance before releasing it. You can now select the setting you
require.
26
Thermo-electric flame failure device
Your wok burner is equipped with a thermo-electric flame failure device. If
the gas flame is extinguished, e.g. by food boiling over or by a draught, the
gas supply is switched off. This prevents the release of gas. If you turn the
control knob to the position, the burner is ready for use again.
The thermo-electric flame failure device operates independently from the
electricity supply. This means that it will still work if the wok burner is
used during a power cut.
Safety features
27
Cleaning and care
Risk of burning due to hot
surfaces. The wok surface, pan supports and burners will be hot after use.
Allow the surfaces to cool down before cleaning the wok.
Risk of damage due to moisture
ingress. The steam from a steam cleaning appliance could reach electrical
components and cause a short circuit. Do not use a steam cleaner to clean the
induction wok.
All surfaces could be discoloured or damaged if unsuitable cleaning agents are
used. All surfaces are susceptible to scratching. Remove any residual cleaning
agent immediately. Never use abrasive sponges or cleaning agents.
Food boiling over can cause discoloration of the burner components. Remove any
soiling and salt and sugar splashes immediately.
When a control knob is pressed down, a spark is generated on the ignitor. Do
not press down the control knob while you are cleaning or touching the wok or
the burner in the vicinity of an ignitor.
Allow the SmartLine appliance to cool down before cleaning.
Clean the SmartLine appliance and accessories after each use.
Dry the SmartLine appliance thoroughly every time after cleaning to avoid
limescale residue.
Unsuitable cleaning agents
To avoid damaging the surfaces of the appliance, do not use: – cleaning agents
containing soda,
alkalines, ammonia, acids or chlorides – cleaning agents containing descaling
agents – stain and rust removers – abrasive cleaning agents, e.g. powder
cleaners and cream cleaners – solvent-based cleaning agents – dishwasher
cleaner – oven sprays – grill and oven cleaners – glass cleaning agents –
hard, abrasive brushes or sponges (e.g. pot scourers), or sponges which have
been previously used and still contain abrasive cleaning agents – dirt erasers
28
Cleaning and care
Cleaning the ceramic surface
Risk of damage by pointed
objects. The seal between the SmartLine appliance and the worktop could suffer
damage. Do not use pointed objects for cleaning.
Do not use washing-up liquid to clean the appliance. Using washingup liquid
will not remove all soiling and residues. Cleaning with washing-up liquid can
result in an invisible film that can lead to discolouration of the ceramic
glass. This discolouration cannot be removed. Clean the ceramic surface
regularly with a proprietary ceramic glass cleaning agent.
Remove any coarse soiling with a damp cloth and more stubborn soiling with a
glass scraper.
Then clean the ceramic glass surface with the Miele ceramic and stainless
steel cooktop cleaner (see “Optional accessories”) or with a proprietary
ceramic glass cleaner applied with kitchen paper or a clean cloth. Do not
apply the cleaner while the cooktop is still hot, as this can result in
marking. Please follow the cleaning agent manufacturer’s instructions.
Finally wipe the cooktop with a damp cloth and dry it with a soft, dry cloth.
Residues can burn onto the cooktop the next time it is used and cause damage
to the glass ceramic surface. Ensure that all cleaner residues are removed.
Spots caused by limescale, water and aluminium residues (spots with a metallic
appearance) can be removed using the Miele ceramic and stainless steel cooktop
cleaner.
Risk of burning due to hot
surfaces. The surfaces get hot during use. Wear oven gloves when removing
residues of sugar, plastic or aluminium foil from a hot cooktop with a glass
scraper.
Should any sugar, plastic or aluminium foil spill or fall onto a hot cooking
zone while it is in use, first switch off the appliance.
Then carefully scrape off these residues immediately whilst they are still
hot, using a shielded scraper blade suitable for use on glass.
Afterwards, clean the glass ceramic surface in its cooled state, as described
above.
29
Cleaning and care
Cleaning the control knob(s)
Clean the control knob(s) using a solution of warm water and a little washing-
up liquid applied with a soft sponge. Stubborn soiling should be soaked first.
Dry the control knob(s) with a clean cloth.
Cleaning the pan supports
Remove the pan supports. Clean the pan supports in the
dishwasher or with a solution of warm water and a little washing-up liquid
applied with a soft sponge. Stubborn soiling should be soaked first. After
cleaning, dry the pan supports thoroughly with a clean cloth.
30
Cleaning and care
Cleaning the burner(s)
Do not clean any parts of the burners in a dishwasher.
The surface of the burner caps will become more matt over time. This is normal
and does not indicate damage to the burner caps. Nor will it affect the
operation of the cooktop. The burner should be dismantled and
then cleaned by hand using a solution of warm water and a little dishwashing
liquid applied with a soft sponge. Clean any soiling from the flame openings.
Danger of explosion!
Blocked flame openings can cause a dangerous build-up of gas in the base of
the cooktop which could ignite and cause an explosion. This can lead to damage
to the appliance and injury. Ensure the flame openings are kept clean at all
times.
Parts of the burner that cannot be removed should be wiped clean with a damp
cloth only.
The ignitor and the flame failure device should be very carefully wiped clean
using a well wrung out cloth.
Do not let the ignitor get wet. If it gets wet, it will not spark. Finally dry
everything thoroughly with
a clean cloth. Make sure that the flame openings are completely dry.
The surface of the burner caps will become more matt over time. This is normal and does not indicate damage to the burner caps. Nor will it affect the operation of the cooktop.
31
Cleaning and care
Assembling the burner(s) a b
c
d
e
f
Place the burner head onto the burner base so that the flame failure device
and the ignitor extend through their respective holes in the burner head. The
burner head must click into place correctly.
Then place the burner caps and in position. Ensure that all parts of the
burner are reassembled in the correct order.
32
Problem solving guide
With the help of the following guide, minor faults in the performance of the appliance, some of which may result from incorrect operation, can be remedied without contacting Miele. This will save you time and money because you won’t need a service call. Please note that a call-out charge will be applied to unnecessary service visits where the problem could have been rectified as described in these operating instructions.
Problem
Possible cause and remedy
The burner does not
There could be an air lock in the gas pipe.
ignite when the cooktop You may need to make several attempts before the
is being used for the
burner ignites successfully.
first time or after it has
not been used for a
longer period.
The burner does not light after several attempts.
There is a fault. Turn all of the control knobs clockwise to the
position and interrupt the power supply to the cooktop for a few seconds.
The burner is not correctly assembled. Assemble the burner correctly.
The gas shut-off valve is closed. Open the gas shut-off valve.
The burner is wet and/or dirty. Clean and dry the burner.
The flame openings are blocked and/or wet. Clean and dry the flame openings.
The gas flame goes out after being lit.
The flames do not touch the flame failure device and the burner does not get hot enough: The burner parts are not positioned correctly. Position the burner parts correctly.
The flame failure device is dirty. Remove any soiling.
The flame suddenly looks different.
The burner parts are not positioned correctly. Position the burner parts correctly.
The burner head or the holes in the burner cap are dirty. Remove any soiling.
33
Problem solving guide
Problem The gas flame goes out during operation. The ignitor on the burner does not spark.
Possible cause and remedy
The burner parts are not positioned correctly. Position the burner parts
correctly.
The mains circuit breaker has tripped. If it has, contact a qualified
electrician or Miele.
There is food residue stuck between the ignitor and the burner cap. The flame
failure device is dirty. Remove any soiling (See “Cleaning and care”).
34
Optional accessories
Miele offers a range of useful accessories, as well as cleaning and conditioning products for your appliance. These products can be ordered from the Miele online shop. They can also be ordered directly from Miele (see end of this booklet for contact details).
FlameGuard
For fitting in place between the downdraft extractor and a gas cooking
appliance.
Original Miele ceramic and stainless steel cooktop cleaner 250 ml
Removes heavy soiling, limescale deposits and aluminium residues.
Original Miele all purpose microfibre cloth
Removes finger marks and light soiling.
35
Service
Contact in case of fault
In the event of any faults which you cannot remedy yourself, please contact
Miele. You can book a Miele customer service call-out online at
www.miele.com.au/ service or www.miele.co.nz/service. Contact information for
Miele can be found at the end of this booklet. Please quote the model and
serial number of your appliance when contacting Miele. This information can be
found on the data plate.
Data plate
Adhere the extra data plate supplied with the appliance in the space below.
Make sure that the model number matches the one specified on the back cover of
these operating and installation instructions.
Warranty
The manufacturer’s warranty for this appliance is 2 years. For further
information, please refer to your warranty booklet.
36
INSTALLATION
Installation Safety instructions for installation
Risk of damage from incorrect installation.
Incorrect installation can cause damage to the SmartLine appliance. The
SmartLine appliance must only be installed by a suitably qualified and
competent person.
Damage from falling objects.
Take care not to damage the SmartLine appliance when fitting wall units or a
rangehood above it. Fit the wall units and the rangehood before the SmartLine
appliance.
The room in which the SmartLine appliance is installed must conform to all
relevant local and national building regulations and safety regulations. In
Australia and New Zealand, gas installations must be in accordance with AS/NZS
5601. The veneer or laminate coatings of worktops (or adjacent kitchen units)
must be treated with 100 °C heat-resistant adhesive which will not dissolve or
distort. Any splashbacks must be of heat-resistant material. An electric fryer
must not be installed directly next to a gas cooktop as the gas flames could
ignite the fat in the fryer. It is essential to maintain a distance of at
least 288 mm between these two appliances. The SmartLine appliance must not be
installed over a fridge, fridge-freezer, freezer, dishwasher, washing machine,
washer-dryer or tumble dryer. When installing the SmartLine appliance, make
sure that the gas pipe and mains connection cable cannot come into contact
with hot appliance parts.
37
INSTALLATION
Installation The mains connection cable and any flexible gas connection pipes
must be installed in such a way so that they do not come into contact with any
moving kitchen parts (e.g. a drawer) after the SmartLine appliance has been
installed, and that they cannot be subjected to any mechanical action which
could cause damage. Carefully observe the safety clearances listed on the
following pages.
38
INSTALLATION
Installation
Safety distances
Safety distance above the SmartLine
Clearance underneath the appliance A minimum safety clearance of 30 mm must be provided underneath the appliance. Please note that clearance must also be provided for the installation of the flexible gas connection hose and mains electrical cable if the appliance is to be installed above a closed surface (e.g. an oven).
A minimum safety distance must be maintained between the SmartLine and the
rangehood above it. See the rangehood manufacturer’s operating and
installation instructions for details. If the manufacturer’s instructions are
not available for the rangehood, a minimum safety distance as per AS/NZS
5601.1 must be maintained. For any flammable objects, e.g. utensil rails, wall
units etc., a minimum safety distance of 600 mm must be maintained between
these objects and the highest part of the SmartLine below.
When two or more appliances which have different safety distances are
installed together below a rangehood, you should observe the greatest safety
distance.
39
INSTALLATION
Installation
Safety distances to the sides and back of the appliance Ideally the appliance
should be installed with plenty of space on either side. There may be a wall
at the rear and a tall unit or wall on one side (right or left). On the other
side, however, no tall unit or wall should stand higher than the appliance.
Before installing the appliance, check that the location provides the required
clearances from combustible material and, if necessary, provide protection to
adjacent surfaces as required by regulations.
Not allowed Recommended
Not recommended
Not recommended 40
INSTALLATION
A gas appliance shall be installed such that the surface temperature of any
nearby combustible surface will not exceed 65 °C above ambient. The minimum
clearance from a combustible surface shall be a 200 mm horizontal distance
from the periphery of any gas burner (AS/NZS 5601.1). If that horizontal
clearance is less than 200 mm, that vertical surface must be protected by a
non-combustible material for 150 mm above the top of the edge of the nearest
burner for the full dimension of the cooktop (depth, width).
X Height from worktop surface to the top of the edge of the burner
The shown area indicates the protected surface, which may be ceramic tiles or
other approved material. Combustible surface: A material which will ignite
and burn, and includes material which has been flameproofed.
Installation
41
INSTALLATION
Installation
Detailed dimensions
Height of pan supports above the worktop surface
a Vertical distance b Worktop surface c Pan support The vertical distance from
the top of the pan supports to the surface of the worktop is 37 mm.
42
INSTALLATION
Installation notes surface-mounted
Sealing between the SmartLine appliance and the worktop
Tiled worktop
Installation
The SmartLine appliance and worktop may be damaged if the appliance needs to be removed after it has been sealed with a sealant. Do not use any sealant between the SmartLine appliance and the worktop. The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop.
Grout lines and the hatched area underneath the SmartLine appliance frame must
be smooth and even. If they are not, the SmartLine appliance will not sit
flush with the worktop and the sealing strip underneath the top part of the
appliance will not provide a good seal between the appliance and the worktop.
Sealing strip
Dismantling the SmartLine appliance for service purposes may damage the
sealing strip underneath the edge of the SmartLine appliance. Always replace
the sealing strip before reinstalling the cooktop.
43
INSTALLATION
Installation
Installing several SmartLine appliances The gaps between the individual
SmartLine appliances must be sealed with a silicone sealant that is
heatresistant to at least 160 °C. With flushfit installation, the gap between
the SmartLine appliance(s) and the worktop must also be sealed with a silicone
sealant that is heat-resistant to at least 160 °C. After installation, the
SmartLine appliances must be easily accessible from below, so that the bottom
half of the casing can be removed for maintenance. If the SmartLine appliances
are not accessible from below, the sealant must be removed so that they can be
removed. Combination with a downdraft extractor If the SmartLine appliance is
installed in combination with a downdraft extractor, the latter must be
installed first.
44
INSTALLATION
Worktop cut-out surface-mounted
B +1
Installation
010 500 + 1
ßR 4 10
B+1
45
INSTALLATION
Installation
Installation with a downdraft extractor
Sample combinations
Number x width [mm]
Cooking appliances
Downdraft extractor
1 x 378
1 x 120
Dimension B
[mm] 481
2 x 378
1 x 120
862
1 x 378 1 x 620 3 x 378
2 x 120 2 x 120
1226 1365
2 x 378 1 x 620 4 x 378
2 x 120 2 x 120
1607 1746
1 x 620
2 x 120
845
46
INSTALLATION
Installation without a downdraft extractor
Sample combinations
Number x width [mm] Cooking appliances
1 x 378
2 x 378
1 x 378 1 x 620 3 x 378
2 x 378 1 x 620 4 x 378
2 x 378 1 x 800 2 x 378 1 x 936
Installation
Dimension B [mm] 359 740 982 1121 1363 1502 1554 1680
47
INSTALLATION
Installation
Spacer bars surface-mounted
If you are installing several appliances, you must fit spacer bars between
them. The clips supplied with the spacer bars are only required for installing
a CSDA 700x FL. Installing 3 appliances and 2 spacer bars
48
INSTALLATION
Installation dimensions Surface-mounted
All dimensions in this instruction booklet are given in mm. Distances from
burner to the edge of the appliance
Installation
49
INSTALLATION
Installation
a Front b Mains connection box with mains connection cable
Mains connection cable L = 2,000 mm c Gas connection R ½” ISO 7-1 (DIN EN
10226) 50
INSTALLATION
Installation
Installation surface-mounted Wooden worktops
Preparing the worktop Create the worktop cut-out.
Remember to maintain the minimum safety distances (see “Installation Safety
distances”). Seal the cut surfaces of wooden worktops with a suitable sealant
to avoid swelling caused by moisture. The sealant must be heat-resistant.
Make sure the sealant does not come into contact with the top surface of the
worktop.
Fitting the spacer bars Use the middle screw holes if one of the following
SmartLine appliances is installed to the right or left of the spacer bar: CS
7611, CS 7641, CS 7101(-1), CS 7102(-1)
Position the spacer bars flush onto the upper edge of the cut-out.
Secure the spacer bars with the 3.5 x 25 mm wood screws supplied.
Granite and marble worktops You will need heavy-duty doublesided tape (not
supplied) to secure the spacer bars.
Stick the tape along the top edge of the worktop cut-out.
Position the spacer bars flush onto the upper edge of the cut-out.
Press the spacer bars firmly into place.
51
INSTALLATION
Installation
Installing the SmartLine appliance Stick the supplied sealing strip under
the edge of the SmartLine appliance. Do not apply the sealing strip under
tension. Feed the mains connection cable down through the worktop cut-out.
Position the SmartLine appliance in the worktop cut-out. Ensure that: – The
seal of the appliance sits flush with the worktop on all sides to ensure an
effective seal all round. – All gap widths are uniform. If the seal does not
meet the worktop correctly on the corners, carefully scribe the corner radii (
R4) with a jigsaw.
Do not use any additional sealant (e.g. silicone) on the SmartLine appliance.
Unsuitable sealant can damage natural stone. For natural stone worktops and
natural stone tiles, only use silicone sealant that is specially formulated
for natural stone. Please follow the manufacturer’s instructions.
Checking operation After installation, ignite all burners to
check that they are operating correctly: – The flame must not go out on the
lowest setting, or when the control is turned quickly from the highest to the
lowest setting. – On the highest setting, the flame must have a distinctive
and visible core.
Connect the SmartLine appliance to the mains electrical supply.
If required, connect the SmartLine appliance to the gas supply (see
“Installation Gas connection”).
Check that the SmartLine appliance works.
Seal the gaps between the individual appliances with a silicone sealant that
is heat-resistant to at least 160 °C.
52
INSTALLATION
Installation
Installation notes flush-fit
Flush-fit installation is only possible in natural stone (granite, marble),
solid wood and tiled worktops. For installation in worktops made of other
materials, please consult the relevant manufacturer as to whether their
worktops are suitable for flush-fit installation. The internal width of the
base unit underneath the appliance must be at least as wide as the inner
worktop cutout (see “Installation Installation dimensions Flush”), so that
the SmartLine appliance is easily accessible from underneath after
installation and the bottom half of the casing can be removed for maintenance.
If the appliance is not freely accessible from below after installation, the
sealant must be removed so that the appliance can be removed.
Natural stone worktops The SmartLine appliance is set directly in the cut-out.
Solid wood worktops, tiled worktops, glass worktops The SmartLine appliance is
set on a wooden frame inside the cut-out. The frame must be provided on site
and is not supplied with the appliance.
Sealing strip
Dismantling the SmartLine appliance for service purposes may damage the
sealing strip underneath the edge of the SmartLine appliance. Always replace
the sealing strip before reinstalling the cooktop.
53
INSTALLATION
Installation
Installing several SmartLine appliances The gaps between the individual
SmartLine appliances must be sealed with a silicone sealant that is
heatresistant to at least 160 °C. With flushfit installation, the gap between
the SmartLine appliance(s) and the worktop must also be sealed with a silicone
sealant that is heat-resistant to at least 160 °C. After installation, the
SmartLine appliances must be easily accessible from below, so that the bottom
half of the casing can be removed for maintenance. If the SmartLine appliances
are not accessible from below, the sealant must be removed so that they can be
removed. Combination with a downdraft extractor If the SmartLine appliance is
installed in combination with a downdraft extractor, the latter must be
installed first.
54
INSTALLATION
Worktop cut-out flush-fit
A +1 B+1
Installation
500 + 1 524 +1
ß R 4
5,5 +0,5 *
0 2
0 10
12
B+1 A +1
Natural stone worktop * 7+0.5 mm with CS 7611 FL
0 10
5,5 +0,5 *
0 2
12
B+1 A +1
Wooden worktop
55
INSTALLATION
Installation
Installation with a downdraft extractor
Sample combinations
Number x width [mm] Dimension A Dimension B
Cooking Downdraft
[mm] [mm]
appliances extractor
1 x 378
1 x 120
505
481
2 x 378
1 x 120
886
862
1 x 378 1 x 620 3 x 378
2 x 120 2 x 120
1250 1389
1226 1365
2 x 378 1 x 620 4 x 378
2 x 120 2 x 120
1631 1770
1607 1746
1 x 620
2 x 120
869
845
56
INSTALLATION
Installation without a downdraft extractor
Sample combinations
Number x width [mm] Cooking appliances
Dimension A [mm]
1 x 378
383
2 x 378
764
1 x 378 1 x 620 3 x 378
1006 1145
2 x 378 1 x 620 4 x 378
1387 1526
2 x 378 1 x 800 2 x 378 1 x 936
1567 1703
Installation
Dimension B [mm] 359 740 982 1121 1363 1502 1543 1679
57
INSTALLATION
Installation
Spacer bars flush-fit
If you are installing several appliances, you must fit spacer bars between
them. The clips supplied with the spacer bars are only required for installing
a CSDA 700x FL. Installing 3 appliances and 2 spacer bars
58
INSTALLATION
Installation dimensions Flush-fit
All dimensions in this instruction booklet are given in mm. Distances from
burner to the edge of the appliance
Installation
59
INSTALLATION
Installation
a Front b Mains connection box with mains connection cable
Mains connection cable L = 2,000 mm c Stepped cut-out (for detailed
illustrations, see “Installation Worktop cut-out
flush-fit”) d 12 mm wooden frame (not supplied, for detailed illustrations,
see “Installation
Worktop cut-out flush-fit”) e Gas connection R ½” ISO 7-1 (DIN EN 10226) 60
INSTALLATION
Installation
Installation flush-fit
Wooden worktops
Preparing the worktop Create the worktop cut-out.
Remember to maintain the minimum safety distances (see “Installation Safety
distances”). Seal the cut surfaces of wooden worktops with a suitable sealant
to avoid swelling caused by moisture. The sealant must be heat-resistant.
Make sure the sealant does not come into contact with the top surface of the worktop. For wooden worktops, secure the wooden frames 5.5 mm below the upper edge of the worktop. For CS 7611 FL, the wooden frame must be secured 7 mm under the upper edge of the worktop.
Position the spacer bars flush onto the lower step of the stepped cut-out.
Secure the spacer bars with the 3.5 x 25 mm wood screws supplied.
Granite and marble worktops You will need heavy-duty doublesided tape (not
supplied) to secure the spacer bars.
Fitting the spacer bars Use the middle screw holes if one of the following SmartLine appliances is installed to the right or left of the spacer bar: CS 7611, CS 7641, CS 7101(-1), CS 7102(-1)
Stick the tape onto the lower step of the stepped cut-out.
Position the spacer bars flush onto the lower step of the stepped cut-out.
Press the spacer bars firmly into place.
61
INSTALLATION
Installation
Installing the SmartLine appliance Stick the supplied sealing strip under
the edge of the SmartLine appliance. Do not apply the sealing strip under
tension. Feed the mains connection cable down through the worktop cut-out.
Position the SmartLine appliance in the worktop cut-out. Ensure that: – The
seal of the appliance sits flush with the worktop on all sides to ensure an
effective seal all round. – All gap widths are uniform. Connect the SmartLine
appliance to the mains electrical supply. If required, connect the SmartLine
appliance to the gas supply (see “Installation Gas connection”). Check that
the SmartLine appliance works. Seal the gaps between the individual SmartLine
appliances and between the appliances and the worktop with a silicone sealant
that is heatresistant to at least 160 °C.
Unsuitable sealant can damage natural stone. For natural stone worktops and
natural stone tiles, only use silicone sealant that is specially formulated
for natural stone. Please follow the manufacturer’s instructions.
Checking operation After installation, ignite all burners to
check that they are operating correctly: – The flame must not go out on the
lowest setting, or when the control is turned quickly from the highest to the
lowest setting. – On the highest setting, the flame must have a distinctive
and visible core.
62
INSTALLATION
Gas connection Risk of explosion due to an
incorrect gas connection. If the gas connection is carried out incorrectly, it
may result in gas leakage. Connection to the gas supply must only be
undertaken by an authorised and registered gas installer in strict accordance
with current local and national safety and building regulations. The installer
is responsible for ensuring that the appliance functions correctly when
installed.
Risk of explosion due to an
incorrect conversion. If the conversion to another type of gas is carried out
incorrectly, it may result in gas leakage. Conversion from one type of gas to
another must only be undertaken by an approved and registered gas installer in
strict accordance with current local and national safety and building
regulations. The installer is responsible for ensuring that the appliance
functions correctly when installed. The gas connection must be installed so
that connection can be made either from inside or outside the kitchen
furniture unit. Every appliance must have its own isolating valve. The
isolating valve must be easily accessible and visible (by opening the cabinet
door if necessary).
Installation
Check with your local gas supplier about the type of gas supplied and compare
this information with the type of gas quoted on the appliance’s data plate.
The cooktop is not connected to an exhaust flue. When installing and
connecting the appliance, please observe the relevant regulations and ensure
it has adequate ventilation once installed.
The gas connection must be made in accordance with national and local
regulations.
Special provisions of the local gas supplier as well as building regulations
must also be observed.
Risk of heat damage.
Gas connections, gas hoses or pipes and mains connection cables can be damaged
if exposed to heat from the cooktop. After installation make sure that neither
the gas hose/pipe nor the mains cable can come into contact with hot parts of
the appliance and that the gas hose/pipe and connections on the cooktop cannot
come into contact with hot exhaust fumes.
63
INSTALLATION
Installation
Risk of explosion due to
damaged gas hoses and pipes. Gas can leak from damaged flexible gas hoses.
Attach flexible gas hoses in such a way that the hose assembly is not exposed
to high temperatures exceeding the maximum recommended by the hose
manufacturer, subjected to strain, kinking, permanent deformation or damage by
vermin.
Connect the cooktop to the gas supply in accordance with national and local
regulations. Check the gas connection for any leaks.
The gas pressure must be set by an approved gas fitter and a full operational
test and a test for possible leakages must be carried out by the gas fitter
after installation.
Depending on country of destination, this appliance is set up for connection
to natural gas or ULPG. See adhesive label on the appliance: – G = NG (natural
gas) – LP = ULPG (Propane/Butane) Depending on country of destination, jets
are supplied for conversion to a different type of gas. If the appropriate
jets have not been supplied with the appliance, you will need to contact
Miele. Conversion to another type of gas is described in the section
“Conversion to another type of gas”.
Connecting the cooktop The cooktop is supplied with a ¹/” threaded gas
connection. There are two connection options:
– Fixed connection.
– Flexible hose class B or D which complies with AS/NZS 1869 and must be
certified. The minimum inner diameter (Ø) must be 10 mm and the maximum length
1200 mm.
Risk of explosion due to gas
leakage. Unsuitable sealant will not ensure the required leak protection for
connections. Ensure that a suitable sealant is used.
64
INSTALLATION
Installation
Setting the gas pressure The gas pressure must be set by the authorised gas
fitter as shown on the data plate: Natural gas 1.0 kPa ULPG (Propane/Butane)
2.75 kPa
The gas pressure must be set with the largest burner operating at maximum
setting. For ULPG models
For natural gas models The gas regulator is only included with appliances
which are set up for connection to natural gas. The regulator must be
connected directly to the appliance.
a
~ 60
a
b a Connection R ¹/” with test point b Connection R ¹/” with test point and
90° angle When using a 90° angle the buildingin depth will increase to the
depth of the elbow used.
a Pressure Test Point
Loosen the screw in the test point until it is free in its housing. The screw
is retained in this position.
Connect the hose from the pressure gauge.
Reassemble one of the large burners, turn on the gas and manually light the
burners.
Disconnect the hose from the pressure gauge and screw in the test point screw.
For natural gas models: Connect the gas regulator directly to the appliance.
65
INSTALLATION
Installation
Burner ratings
Nominal ratings Gas type
Natural gas ULPG
Highest setting MJ/h 16.0 14.3
Lowest setting MJ/h 0.7 0.6
66
INSTALLATION
Installation
Electrical connection
The SmartLine appliance is supplied with a mains connection cable with moulded
plug ready for connection to a suitable earthed socket. The socket should be
easily accessible after the SmartLine appliance has been installed. If the
socket is not easily accessible, ensure that a suitable means of disconnection
is provided on the installation side for each pole.
Risk of fire from overheating.
Connecting the SmartLine appliance to multi-socket adapters or extension
cables can overload the cables. For safety reasons, do not use an extension
cable or multi-socket adapter.
Risk of damage from incorrect connection. Incorrect installation, maintenance
and repairs can be dangerous to users. Miele cannot be held liable for damage
or injury (e.g. electric shock) caused by unauthorised installation,
maintenance or repair work, or by an inadequate or faulty on-site earthing
system. All electrical work must be carried out by a suitably qualified and
competent person in strict accordance with national and local safety
regulations. For safety reasons, we recommend using a suitable residual
current device (RCD) in the relevant electrical installation for connecting
the SmartLine appliance.
If the mains connection cable is damaged, it must only be replaced with a specific mains connection cable of the same type (available from Miele). For safety reasons, such replacement may only be carried out by a suitably qualified and competent electrician or a Miele authorised service technician, in order to avoid a hazard. These operating instructions and the data plate indicate the nominal power consumption and the connection data. Compare this information with the data of the on-site electrical connection.If in any doubt, consult a qualified electrician. Temporary or permanent operation with a self-sufficient or non-mains synchronous energy supply system (e.g. isolated networks, back-up systems) is possible. A requirement for the operation is that the energy supply system complies with all current local and national requirements that apply to stand-alone, solar and/or battery systems. The protective measures provided in the domestic installation and in this Miele product must also be assured in their function and operation in isolated operation or in non-mains synchronous operation, or replaced with equivalent measures in the installation.
67
INSTALLATION
Conversion to another type of gas
Risk of explosion due to an
incorrect conversion. If the conversion to another type of gas is carried out
incorrectly, it may result in gas leakage. Conversion from one type of gas to
another must only be undertaken by an authorised and registered gas installer
in strict accordance with current local and national safety and building
regulations. The installer is responsible for ensuring that the appliance
functions correctly when installed. Disconnect the cooktop from the
electricity supply and turn off the gas supply.
Jet table
The jet markings refer to a ¹/ mm bore diameter.
Gas type
Natural gas ULPG
Main jet
Small jet
2 x 1.20 / 0.90 0.88 / 0.42
2 x 0.67 / 0.46 0.52 / 0.23
Changing the jets
Disconnect the cooktop from the electricity supply and turn off the gas
supply.
When converting to another type of gas, both the main and small jets need to be changed.
68
INSTALLATION
Changing the main jets
a b
c
Conversion to another type of gas
Changing the small jets Remove the burner components. Unscrew the burner’s
fixing screws. Pull the control knob off. Loosen the fixing nuts/screws
(depending on the model) on the underside. Carefully remove the underside of
the appliance.
d
a
Remove the burner caps and burner head .
Using an M7 socket spanner, unscrew the main jets .
Fit the correct jets securely (see jet table).
Secure the jets against inadvertent loosening with sealing wax.
c
b
a Ignition switch b Small jet with smaller diameter c Small jet with larger
diameter
Remove the ignition switch . Using a small screwdriver, unscrew
the two small jets in the gas fitting. Pull out the jets with a pair of long
nose pliers.
69
INSTALLATION
Conversion to another type of gas
Fit the correct jets securely (see jet table).
Secure the jets against inadvertent loosening with sealing wax.
Checking operation
Check all gas fittings for leaks. Reassemble the cooktop. Ignite all burners
to check that they
are operating correctly. – The flame must not go out on the
lowest setting, or when the control is turned quickly from the highest to the
lowest setting. – On the highest setting, the flame must have a distinctive
and visible core. Adhere the label supplied with the jets over the old label
stating the type of gas being used.
70
Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398
Miele Head Office Melbourne: Level 4, 141 Camberwell Road Hawthorn East, VIC
3123
Miele Experience Centre Doncaster: 1136/7 Doncaster Shopping Centre 619
Doncaster Rd, Doncaster, VIC 3108
Miele Experience Centre South Melbourne: 206-210 Coventry Street South
Melbourne, VIC 3205
Miele Experience Centre and Office Sydney: 3 Skyline Place Frenchs Forest, NSW
2086
Miele Experience Centre and Office Brisbane: Tenancy 4C, 63 Skyring Terrace
Newstead, QLD 4006
Miele Experience Centre Gold Coast: 131 Ferry Road Southport, QLD 4215
Miele Experience Centre and Office Adelaide: 83-85 Sir Donald Bradman Drive
Hilton, SA 5033
Miele Experience Centre and Office Perth: 205-207 Stirling Highway Claremont,
WA 6010
1300 464 353 (1300 4 MIELE) www.miele.com.au
Miele New Zealand Limited IRD 98 463 631 Miele Experience Centre and Head
Office Auckland: 8 College Hill Freemans Bay, Auckland 1011 Miele Experience
Centre Wellington: 183 Featherston Street Wellington 6011 0800 464 353 (0800 4
MIELE) www.miele.co.nz
Miele Global Headquarters Germany Miele & Cie. KG Carl-Miele-Straße 29 33332
Gütersloh Federal Republic of Germany
CS 7101-1 en-AU, NZ
M.-Nr. 11 503 510 / 01
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>