serenelife SLPORBT18 Automatic Robotic Pool Cleaner User Guide
- June 6, 2024
- serenelife
Table of Contents
serenelife SLPORBT18 Automatic Robotic Pool Cleaner
Product Introduction
We are sure that your SERENELIFE Automatic Robotic Pool Cleaner will provide you with reliable, convenient and cost effective pool cleaning. Its reliable ffltration in all pool conditions, active brushing, and all-surface climbing brush enhance maximum pool hygiene.
The Automatic Robotic Pool Cleaner by SERENELIFE deliver advanced cleaning technology, long lasting performance and easy maintenance. You and your family will be free to enjoy swimming with full confidence that your pool is completely clean.
WARNING AND CAUTIONS
WARNING: Do not operate the robotic pool cleaner when there are people swimming in the pool. Communication cable can trip or entangle swimmers which could result in drowning.
WARNING: Keep the robotic pool cleaner out of reach of children. Keep the robotic pool cleaner out of reach of persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, without proper supervision and understanding of the instructions.
WARNING: DO NOT switch on the pool cleaner if it is not immersed in the water. Operating the cleaner out of the water may cause severe damage and will result in loss of warranty.
WARNING: • Shut off and unplug the power supply every time you remove the cleaner from the water.
WARNING: DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE, USE THE HANDLE.
WARNING: Only use this cleaner when the water temperature is 10-35°C or 50-95°F and the pool depth is 0.5m-3m. The cleaner is designed for 100m surface area.
WARNING: Keep the controller box in a dry place which is out of direct sunlight and is 3.5m away from your pool.
GETTING STARTED
- : Turn power supply ON/OFF, error alarm.
- FLOOR CLEAN ONLY: To clean the pool floor only. It will increase the cleaning efficiency
- ALL PURPOSE CLEAN: All-around cleaning, including pool floor, pool wall and waterline.
- RUNNING TIME (set the cleaning time): Set the preferred running hours (2/3/5 hours, press the button to set the cleaning time, red light means the cleaner will work for 2 hours, green light for 3 hours, blue for 5 hours), before you start the cleaning. The cleaner will stop automatically after working.
OPERATION INSTRUCTIONS
-
Place the power supply (transformer) at least 3.5 meters/11.5 feet from the pool and atleast 12 cm/4 Inch above the surface. The transformer will supply lowvoltage to the cleaner.
-
Connect floating power cord.
-
Place the unit in the water. Release the Pool Cleaner and let it sink to the floor of the pool. Make sure that the floating cable is free of any obstructions.
-
Start: Turn the power supply ON (115V AC 60HZ). One of the three modes light will be on. Press the button for the mode and time you want to run, then press button, the Pool Cleaner will now operate.
-
Mode switching: Press button, choose the mode, press button to start the cleaner.
-
Indicator Lights:
DAILY MAINTENANCE
-
Clean the Filter Basket
Cut off the power supply (light goes out) Turn off the Pool cleaner. Open the filter cover. Clean the filter basket with a hose. Insert the clean filter basket and close the filter cover.
Make sure the power supply is switched off and unplugged. It is highly recommended to clean the filter basket after each cleaning cycle. -
Floating cable daily maintenance
The floating cable may get intertwined after 6 hours of working which need to be sorted out manually. It highly recommend to sort the cable out after each cleaning.
TROUBLESHOOTING
| Symptom | Possible Reason | Solution |
|---|---|---|
| The pool cleaner moves but does not clean the pool | Clogged filt er basket |
Clean the filter basket
The pool cleaner does not move|
- The impeller get blocked.
- The drive belt get blocked
| Check and clean the obstacle
Debris out from the outlet|
- Filt er basket is broken
- Filt er basket is full
|
- Replace the filter basket
- Clean the filter basket
Intertwined floating cable| Long working hours, over 8 hours.| Untwist the
floating cable before re-start.
Twinkling| Overload or no-load protection| Let the cleaner sink to the floor
of the pool, and press **** to start again.
SPECIFICATIONS
Features
- Design to Clean the Pool Effortlessly
- With Dual Scrubbing Brushes and Superior Filtering Capabilities
- Saves Energy
- Traps and Locks-in All Sorts of Dirt and Debris
- Tangle-Free Cable
- Easy to Use
- Ideal for In-ground Swimming Pools Up to 50 Feet
- Fully Automatic Robot Cleaner
What’s in the Box
- Cleaner
- Control box
- Manual
Technical Specs:
- Construction Materials: ASA
- Cleaning Area: Up to 50 Feet
- Cleaning Coverage: Floor and walls
- Cleaning Cycle Time: 2 hours,3 hours, 5 hours (three modes)
- Filtration Accuracy: ≥100μm
- Length of Floating Cable: 55.8 ft.
- Filter Speed: 14-18 m3/h
- Filter Type: Twin Cartridges
- Output Voltage: 24V DC
- Output Current: 4.5A
- Input Voltage: 115V
- Frequency Response: 60Hz
- Horsepower: 150W
- IP Class for Controller Box: IP54
- IP Class for Motor: IP68
- Suction Rate: 4500 GPH
- Product Dimensions: 18.5” x 16.1” x 10.03” -inch
Parts Breakdown and Replaceable Parts List
NO.
| Parts Name|
Qty
---|---|---
1| Cover and wiring assembly| 1
2| Filter Basket| 2
3| Motor box| 1
4| Wheel Brush| 2
5| Buoyancy block| 1
6| Driven wheel| 4
7| Bearing| 20
8| Side panel| 2
9| Controller Box| 1
10| Drive wheel| 2
11| Drive belt| 2
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email:[email protected]
