uhuru WKM-18 Keyboard and Optical Mouse User Manual
- June 6, 2024
- Uhuru
Table of Contents
uhuru WKM-18 Keyboard and Optical Mouse
INSTALLATION
Install the Batteries
The RF2.4GHz Optical mouse use one AA alkaline battery The RF2.4GHz Optical
keyboard use one AAA alkaline battery
Install battery in the mouse/ Install battery in the keyboard
- Step 1. Open the battery compartment
- Step 2. Insert the battery as shown inside the battery compartment Step 3. Replace the cover
Install battery in the mouse/ Install battery in the keyboard
- Step 1: Remove the battery compartment cover on the bottom of the keyboard by squeezing the cover in from thetab to release it
- Step2 : Insert the batteries as shown inside the battery compartment
- Step3: Replace the cover
Connecting the Receiver
Pis insert the USB receiver into the USB port of your computer or laptop.
The connection will be done automatically after 1-3 seconds.
Multimedia Hotkeys functions
Pressing Fn + Esc = enable or disable the Multimedia Hotkeys functions
- Fl :Previous Track FS:Search
- F2:Play/Pause
- F3:Next Track
- F4:Mute
- F5:Volume Down
- F6:Volume Up
- F7:Web home
- F9:EmaiIFl 0:My Favorite
- Fl 1: save
- F 12: computer settings
- fill : Copy
- fill: Paste
- fill : calculator
Obtain the receiver on the mouse
- lf you want ta use the mouse, pis take out the receiver (shown in picture(])) and connect it to computer;
- If you want to stop using the mouse, pis put the receiver back to the mouse (shown in picture @)
- Take out the receiver
- Store the receiver
Restoring factory default settings
Mouse:
When the end-user finds the wireless mouse doesn’t work, please check:
- Whether the battery is used out, if yes, please replace it with a new battery;
- If the indicator light on the bottom of the mouse is off, please restore the default setting (automatic pairing) by following steps:
- Step 1: unplug and plug again the nano receiver into an available USB port of the computer.
- Step 2: make the wireless mouse close to the nano receiver (within 10 cm), take out the battery and install the battery again inside the battery compartment, if the indicator light on the bottom of the mouse is on, you can use the wireless mouse again.
Power-Save function:
- Without using the mouse for 1 minute, the mouse will go into sleep mode level 1. You can move it to wake up the mouse. The Red LED is still on.
- Without using the mouse for 1-8 minutes, the mouse will go into sleep mode level 2. You can move it to wake up the mouse.The Red LED keep flashing.
- Without using the mouse for more than 8 minutes, the mouse will go into deep sleepthe mouse will go into deep sleep mode and the LED will be turn off automatically. automatically.
State of standby and wake up the mouse
Without any clicks or scroll movement for 8 minutes, the mouse will go into
standby mode. Click any button scroll the wheel to wake up the mouse. Under
this ECO mode, the optical Red LED will be turn off automatically and the
mouse won’t respond by moving it.
- Technical support:[email protected]
- For more products:www.uhurumobility.com
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:\
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution:
Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.