LTS Security LTK1107M Mifare Card Reader User Manual

June 6, 2024
LTS Security

 LTS Security LTK1107M Mifare Card Reader

About This Manual

This manual is applicable to face recognition terminal. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website. Please use this user manual under the guidance of professionals. Legal Disclaimer REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help..

The device must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

  • This device may not cause harmful interference.
  • This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement

This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive. 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see. www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include.

lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. Use only power supplies listed in the user instructions:

Model Manufacturer Standard

TS-A018-120015Ec

| Shenzhen Transin Technologies Co., Ltd| CEE

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.

 |
---|---
Warnings Follow these safeguards to prevent serious injury or death.| Cautions Follow              these precautions to prevent potential injury or material damage.

Warnings

  • All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region.
  • Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value.
  • Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
  • Please make sure that the power has been disconnected before you wire, install or dismantle the device.
  • When the product is installed on wall or ceiling, the device shall be firmly fixed.
  • If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
  • If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)

Cautions

  • Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
  • Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The appropriate temperature is -20℃ to 65℃.
  • The device cover for indoor use shall be kept from rain and moisture.
  • Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger).
  • Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
  • Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.
  • Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents.
  • Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs.
  • Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.

Preventive and Cautionary Tips
To guarantee the card reader works properly, please read and obey the notes below.

  • If the card reader is powered by the controller, the power supply distance is recommended to be no longer than 100m. If the distance is longer than 100m, you are advised to power the card reader by external 12V (range: -%10 ~ +%10) DC
  • To guarantee the communication between the controller and the card reader, you must use RVVP cable above 0.5 to connect them.
  • If the card reader is installed outside or in environment easy to permeable, it is advisable to install a waterproof shield.
  • If you need to install several card readers, the distance among them must over 30cm.
  • To reduce the noise in long distance transmission, the shield of cable should connect to the GND of both controller and card reader terminal.
  • Please take care of your card and report card loss in time when card is lost.
  • If you require a higher security level, use multiple authentication modes.
  • Multiple card types are supported. Please select an appropriate card type according to the card performance and the usage scenarios.

Preventive and Cautionary Tips

To guarantee the card reader works properly, please read and obey the notes below.

  • If the card reader is powered by the controller, the power supply distance is recommended to be no longer than 100m. If the distance is longer than 100m, you are advised to power the card reader by external 12V (range: -%10 ~ +%10) DC power supply, which is nonswitched and linear.
  • To guarantee communication between the controller and the card reader, you must use RVVP cable above 0.5 to connect them.
  • If the card reader is installed outside or in an environment easy to permeable, it is advisable to install a waterproof shield.
  • If you need to install several card readers, the distance among them must over 30cm.
  • To reduce the noise in long-distance transmission, the shield of cable should connect to the GND of both controller and card reader terminal.

Over View

LTS Security LTK1107M Mifare Card Reader fig 1

The card reader is a kind of high-performance product, with a 32 bit high- speed processor. It communicates with access controller via either RS-485 protocol (AES encrypted) or Wiegand protocol. And a build-in tamper-proof module helps to protect card reader from malicious damage. As to the physical appearance, the PC+ABS material makes water proof and dust proof possible in poor environment.

Indicator and Component

LTS Security LTK1107M Mifare Card Reader fig 2

Introduction for DIP Switch

The DIP switch module is shown below. The No. of DIP switch from left to right is 1 ~ 8.

Description of DIP Switch
No. Description DIP Switch Status
1 ~ 4 Address of RS-485 1: 1

0: 0

5

| Card Security

Note: Only available when

Wiegand is enabled.

| 0: Disable M1 card encryption  function,

disable non-M1 card

No. Description DIP Switch Status
    Recognition function,            enable door open via NFC card.

1: Enable M1 card encryption function, enable non-M1 card Recognition function,           disable door open via NFC

card.

6| Wiegand protocol or RS-485

protocol.

| 0: Wiegand protocol;

1: RS-485 protocol.

7

|

Wiegand Protocol (available when No. 6 is 0)

| 1: Wiegand protocol of 26-bit;

0: Wiegand protocol

of 34-bit.

8| Matched Resistance

(available for RS-485 protocol)

| 1: Enable;

0: Disable.

Definition of Cable
The description of 10 cables is shown below.

Description of Cable

Color Description
Orange Red LED Control (available for Wiegand Protocol)
White Wiegand W1 (available for Wiegand Protocol)
Green Wiegand W0 (available for Wiegand Protocol)
Color Description
--- ---
Blue RS-485-
Yellow RS-485+
Red PWR (+12 VDC)
Black GND
Gray TAMPER (available for Wiegand Protocol)
Purple Beep Control (available for Wiegand Protocol)
Brown Green LED Control (available for Wiegand

Protocol)

Wiring Cables

Purpose:
Wire the cables between controller and card reader, thus establishing the communication between them.

Steps for RS-485 communication mode:

  1. Set the DIP switch of No. 6 as 1.
  2. Set the DIP switch of No. 1 ~ 4 for RS-485 address. For details, please refer to 3.1 Introduction for DIP Switch.
  3. Wire the cable between controller and card reader as shown below.

Wiring for RS-485 Communication Mode Steps for Wiegand communication mode

  1. Set the DIP switch of No. 6 as 0.
  2. Set the DIP switch of No. 5 and 7 for reading card mode and Wiegand protocol. For details, please refer to 3.1 Introduction for DIP Switch.

Wiring the cable between controller and card reader as shown below.

Installing Card Reader

Before you start:
Set the DIP switch. For details, refer to 3.1 Introduction for DIP Switch.

Installation for LTK1101/ 02/ 03/ 04 series card reader Steps.

  1. Fix the plate on the wall or other places by using two screws (PA4×25-SUS). Make sure the arrows on the plate are upwards.
  2. Check whether the plate is fixed and in the right direction.
  3. Slide the card reader from direction A to B along the plate side until the bottom matches the joint. Make sure the card reader is tightly on the wall or other places.
  4. Drag and move the card reader to make sure it is fixed.

Sound Prompt and Indicator

After the card reader is powered on, LED status indicator will turn green and flashing for 1 time. Then it will turn red and flashing for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. When using the card reader, it will send out different sounds prompt and the LED indicator to indicate different statuses. You can refer to tables below for detailed information.
Description of Prompt Sound

Sound Prompt Description

One beep

| Swiping card prompt
Pressing keys prompt
Prompt for too long card No. input by

pressing keys.

Time out prompt for pressing keys or

swiping card.

For Card + Password authentication: prompt for entering password after swiping

the card.

Two rapid beeps| The operation of pressing keys or swiping

card is valid.

Three slow beeps| The operation of pressing keys or swiping

card is invalid.

Rapidly continuous beeps| Prompt for tamper-proof alarm.
Prompt for buzzer alarm.
Slowly continuous

beeps

| The card reader is unencrypted.
LED Indicator Status| Description
---|---
Green (flashing for 1 time),        and        red

(flashing for 3 times)

|

The card reader is power on.

Flashing green

| For Card + Fingerprint authentication: prompt for pressing the fingerprint after

swiping the card.

The operation

fingerprint.

| of| configuring| the
Solid green for 2s| The operation of pressing keys or swiping

card is valid.

Solid red| Card reader is working normally.
Flashing red for 3

times

| The operation of pressing keys or swiping

card is invalid.

Flashing red| For RS-485 protocol: Registering failed or

card reader is offline.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals