iridium RST706B Beam Whip Dual Mode Antenna Instruction Manual
- June 6, 2024
- iridium
Table of Contents
RST706B Beam Whip Dual Mode Antenna
Instruction Manual
Kit Contents
1. Antenna
2. Lock Washer| 3. Lock Nut
4. 5m Cable Set
---|---
Introduction
The Iridium Beam Whip Dual Mode Antenna (RST706B) is intended for Land-based
applications. Designed to work with Beam Iridium products and other Iridium-
based devices.
Iridium Whip Dual Mode Antennas (RST706B) excel in SUV/4WD/RV and Truck
applications where a rugged antenna giving the highest possible clearance
above the roofline is required. The antenna can be easily fitted to the bull
bar of a vehicle and has 5 meters (16 ft) of cable included.
Important Safety Information
WARNING
Changes or modifications not expressly approved by Beam Communications could
void the user’s authority to operate the equipment or the warranty.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference and
- this device must accept any interference received, including interference that may cause undesired operation.
Antenna Installation Location
The antenna should be attached in a location that provides the clearest line of sight to the sky without obstruction or interference. Ideally, the antenna should be fitted on the bull bar of a vehicle. Most bull bars already have a fitting and hole for this type of antenna, if not, then a suitable hole or fixing plate will be required.
Outside/Vehicle Installation Options
-
The antenna requires a slotted 16mm diameter mounting hole in order to secure the antenna.
If the vehicle does not have a slotted 16mm mounting hole, then an optional bracket may be required. -
Feed the Satellite Cable and GPS cable through the slot and secure the antenna with the bolt and lock washer provided.
-
Run the cables through to the Beam Docking Station or Iridium handset installed inside the vehicle, be sure to secure the cables appropriately so that the
cable does not rattle or cause any interference or obstruction. Be sure to waterproof the entry point of the cables into the vehicle.
Antenna Connections
Connect the TNC adapter to the TNC connector on the loom coming from the dock or the TNC Bulkhead at the rear of the terminal.
Connect the GPS cable running from the antenna to the SMA connector on the loom coming from the dock or the SMA Bulkhead at the rear of the terminal.
Specifications
GENERAL
Antenna| Iridium| GPS
Polarization| Right Hand Circular (RHCP)| Right Hand Circular (RHCP)
Axial Ratio| 3dB at boresight| 3dB
Impedance| 50 Ohms| 50 Ohms
VSWR| ≤ 2:1| ≤ 2:1
Power Handling| 10 Watts| 1 Watt
Amplifier Gain| 5dBi| 26 ± 2dB
Noise Figure| | 2.5dB Max
DC grounding| Yes| Yes
Cable| Includes 5m or 16.4ft of LMR240UF| Includes 5m or 16.4ft of RG316
ENVIRONMENTAL
Temperature| Degrees ºC| Degrees ºF
Operating| -40 to +85| -40 to +185
PHYSICAL
Colour| Black
Material| Black fiberglass radome, black finish aluminum ferrules, 304
stainless steel ‘barrel’ spring, external coaxial cables and terminations
Mounting
requirements| Minimum M12 hole
Dimensions| mm| inches
Antenna| 800 H| 31.5 H
Weight| kgs| lbs
Antenna| 2.7| 5.9
CONNECTORS
Iridium| TNC Male
GPS| SMA Male
FREQUENCY
Iridium| 1616 – 1626 MHz
GPS| 1575 ± 10 MHz
BEAM Communications Pty Ltd
5/8 Anzed Court, Mulgrave
Victoria, 3170, AUSTRALIA
Tel: +61 3 8588 4500
Fax: +61 3 9560 9055
Info: info@beamcommunications.com
Support:support@beamcommunications.com
www.beamcommunications.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>