VPL-1006 Low Voltage Landscape Lighting Installation Guide
- June 6, 2024
- VOLT
Table of Contents
VOLT® Low Voltage Landscape Lighting
VOLT® Coachman LED Path & Area Light
VPL-1006
INSTALLATION INSTRUCTIONS
VOLT® Coachman LED Path & Area Light VPL-1006
Important: Please Read Before Installation
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC).
Failure to adhere to these codes and instructions may result in serious
injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance, or mounting situations.
- Make sure that the power is turned OFF before installing or servicing this luminaire.
- WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from the pool, spa, or fountain.
- This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
- Wiring connections must be made with UL-listed wire connectors that are suitable for outdoor use.
- Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire, or fitting.
- The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).
Important Safety Instructions
THE LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
- Turn off/unplug and allow to cool before reducing the lamp.
- The lamp gets HOT quickly!
- Do not touch the hot lens, guard, or cowl.
- Keep the lamp away from materials that may burn.
- Do not touch the lamp at any time.
- Use a soft cloth.
- Oil from the skin may damage the lamp.
- Do not operate the fixture with a damaged or missing lens or shield.
Package Contents
A. (1) Fixture
B. (1) Stem
C. (1) Ultra Realistic LED Moving Flame Bi-Pin Candle
D. (1) 17” Stake
Additional Parts Required (sold separately)
A. (1) LED SCB Lamp
Product Dimensions
1Remove the Hat
Remove the hat from the stem by removing the set screws from the hat mount.
2Install LED Lamp
Insert the lamp with the correct wattage and type marked on the fixture label.
CAUTION: Do not exceed the maximum wattage marked on the luminaire label.
NOTE: DO NOT touch the bulb with bare hands. Use a soft cloth to handle
the bulb.
3 Reinstall Hat
After installing the LED lamp into the socket, place the hat back onto the
mount at the top of the stem.
Secure both pieces in place with the set screws previously removed. Hand
tightens until snug.
4 Remove Upper Part of Hat
Remove the upper part of the hat by loosening the set
screws.
5 Install LED Bi-Pin Candle
Insert Ultra Realistic LED Moving Flame Bi-Pin Candle.
CAUTION: Do not exceed the maximum wattage marked on the luminaire label.
6 Reinstall Upper Part of Hat
Place the upper part of the hat back onto the lower part of the hat and secure with the set screws previously removed. Hand tightens until snug.
7 Install Stem
Pass the supply wires through the stem and extension. Then thread the extension onto the stem. Hand tightens until snug.
8 Install Stake and Conduit
Dig a hole in the ground for the conduit runs and the stake. Install the conduit. Slide the stabilizer grid onto the stake and secure it with the screws. Place the stake over the conduit runs. Backfill against the mounting stake.
9 Remove Cap from Stake
Remove the cap from the stake by loosening the set screws.
10 Install Cap to Fixture
Thread the cap onto the fixture body and hand tighten until snug.
11Wire Connection and Fixture Installation
Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.
Help Hotline: 1-813-978-3700
• Mon-Fri 8am-8pm
• Sat-Sun 10am – 6pm (EST)
www.voltlighting.com
Specifications and product details are subject to change without notice.
© Copyright 2021, VOLT® Lighting, Lutz FL USA 33549
• All rights reserved.
customersupport@voltlighting.com
• 813.978.3700 is-VPL-1006-ver7.pdf
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>