Miku Pro Smart Baby Monitor User Guide
- June 6, 2024
- miku
Table of Contents
Miku Pro Smart Baby Monitor
Safety
WARNING: STRANGULATION HAZARD — Children have STRANGLED in cords.
NEVER attempt to use cord without the protective covering. Check protective
covering before each use to ensure that the cord is not exposed to your child.
Immediately discontinue use if protective covering is damaged or broken. This
device is designed for indoor use only. This device is designed to be used
behind a standard crib and against the wall only. Use only the AC power supply
included with your Miku. Adult assembly is required. Keep small parts away
from children when assembling. This product cannot replace adult supervision.
Ensure your child’s health by checking on him/her regularly. This product is
not a toy. Do not allow children to play with it.
DISCLAIMER — Miku Baby Monitor was created to help parents track factors that affect their baby’s sleep schedule and general wellbeing. It is not intended to cure, treat, or prevent any disease or health condition, including, but not limited to, Sudden Infant Death Syndrome (SIDS). No baby monitor can ever replace you as a caregiver, or substitute for asking your doctor for medical advice.
In the box
Optional
universal hardware 
What you’ll need
Note: If you would like to avoid wall installation consider a Miku Stand.
For wall installation videos visit
mikucare.com/support
Get the app
Download the free Miku app from mikucare.com/app and create your user account. Open the App and follow along to pair your Miku.
Installation for drywall
Position the crib against the preferred wall in the nursery.
IMPORTANT: CRIB CENTER MUST BE IN A STUD-FREE AREA OF THE WALL. If
unsure, use a stud finder. For wall surfaces other than drywall, please go to
mikucare.com/support 
Using the Measuring Tape, find the center of the crib
and mark the wall with a pencil.
Note: Center of crib must be within 6 feet of an electrical outlet.
Then, move the crib away from the wall. 
Step on the bottom of the Measuring Tape so it aligns with
the floor and your “Crib Center” mark on the wall. Lift the tape up 60 inches
and mark at the “Mark Here” indicator. Take the Wall Mount and place it over
your mark at 60 inches so you can see the mark through the center hole. Use
the Level below the Wall Mount to verify that it is level. Mark the wall
through the two holes in the Wall Mount. 
Pull and remove the Level from the bottom of the Wall
Mount. Using the Screwdriver, push and twist into the two marks to create
larger holes in the drywall. Only push as far as the black tip of the
Screwdriver. 
Push the Large
Drywall Anchors into each hole and screw them until they are flush.
Note: If the wall anchor doesn’t screw into the wall easily, you may have
hit a stud. In this case no wall anchor is required for that hole. Position
the Wall Mount over the “+” holes of the anchors. Screw the Large Screws into
the “+” holes and secure the Wall Mount until flush with the wall. Unroll the
Power Supply and align the top rubber indicator to the center of the Wall
Mount, leaving the top of the cord hanging. Using the Screwdriver, push the
rubber indicator into the Wall Mount to secure the Power Supply. Slide the
base of the Miku device into the Wall Mount until it clicks. Plug the Power
Supply into the back of the Miku device. Insert the first Cable Guide into the
bottom holes of the Wall Mount, making sure the Cable Guide is covering the
cord. 
Remove the
adhesive strips and adhere to wall.
The adhesive strip needs to cure to the wall for a period of 15 minutes to
take hold.
Note: If you need to customize your cord path, you may need to use our
Optional Cable Guide Hardware. Insert each Cable Guide into the bottom holes
of the previously installed section. Remove the adhesive strips and adhere to
the wall. One by one, insert each Cable Guide into the bottom holes of the
previously installed section for all six sections. Remove the adhesive strips
and adhere to the wall. Connect the Power Cord to the Power Supply. Plug the
Power Cord into the nearest outlet. Once the power button light turns on,
you’re ready to go.
Limited warranty & compliance
For information on Miku’s Limited Warranty visit:
mikucare.com/warranty
Miku, Inc. | Miku Life Monitor || | Model No: M0101 | FCC ID: 2AQM3M0101
Contains TX FCC ID: 2AD9QX4M05 | IC: 24123-M0101 | Contains TX IC ID:
22782-X4M05 | CAN ICES-3(B)/NMB-3(B)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B dig-ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installa-tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encour-aged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
RF EXPOSURE WARNING:
The equipment complies with FCC RF exposure limits set forth for an
uncontrolled environment. The equipment must not be co-located or operating in
conjunction with any other antenna or transmitter. This equipment should be
installed and operated with minimum distance 20cm between the radiator and
your body. It could be removed.
CANADA, INDUSTRY CANADA (IC) NOTICES
This device complies with Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
RADIOFREQUENCY (RF) EXPOSURE INFORMATION
The radiated output power of the Wireless Device is below the Industry Canada
(IC) radio frequency exposure limits. The Wireless Device should be used in
such a manner such that the potential for human contact during normal
operation is minimized. This device has also been evaluated and shown
compliant with the IC RF Exposure limits under mobile exposure conditions.
(antennas are greater than 20cm from a person’s body).
5GHZ WI-FI OPERATION
The device for operation in the band 5150–5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite
systems;
RF EXPOSURE INFORMATION
This device meets the EU requirements (2014/53/EU) on the limitation of
exposure of the general public to electromagnetic fields by way of health
protection.
CE MARK WARNING
This is a Class B product, in a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
POWER ADAPTER WARNING
The adapter shall be installed near the equipment and shall be easily
accessible.
RF POWER SPECIFICATIONS
SIMPLIFIED
EU DECLARATION OF CONFORMITY
Hereby, Miku, Inc., 10 Woodbridge Center Drive Suite 525, Woodbridge, NJ 07095
declares that the radio equipment type Miku Life Monitor || M0101 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
mikucare.com/EU
THE ABBREVIATIONS FOR MEMBER STATES SHALL BE AS FOLLOWS:
Austria (AT), Belgium (BE), Bulgaria (BG), Cyprus (CY), Czech Republic (CZ),
Denmark (DK), Germany (DE), Estonia (EE), Spain (ES), France (FR), Finland
(FI), Greece (GR), Croatia (HR), Hungary (HU), Ireland (IE), Italy (IT),
Latvia (LV), Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL),
Poland (PL), Portugal (PT), Romania (RO), Slovenia (SI), Slovakia (SK) and
Sweden (SE).
This device meets the EU requirements (2014/53/EU) on the limitation of
exposure of the general public to electromagnetic fields by way of health
protection. This equipment should be installed and operated with minimum
distance 20 cm between the radiator and your body .