ring 5AT3T2 Floodlight Cam Wired Plus Instructions
- June 6, 2024
- Ring
Table of Contents
ring 5AT3T2 Floodlight Cam Wired Plus
Important Product Information
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules. This equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunc-tion with any other antenna
or transmitter.
THEFT PROTECTION
If your Ring camera or doorbell product is stolen at any time after your
purchase, Ring will replace the stolen device at no charge to you. This theft
protection is not transferable and applies only to the original consumer
purchaser. Coverage of this theft protection is limited to one (1) replacement
only for each Ring camera or doorbell product that you have purchased. Theft
protection does not apply to any products purchased from third party sellers
on eBay and other online marketplaces. Any claim based on theft of your Ring
camera or doorbell product must be submit-ted within fifteen (15) days of the
theft and include the original sales receipt, and a copy of a police report
evidencing that you reported the theft to the police. Failure to report the
theft to police voids this theft protection.
SAFETY INFORMATION:
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC
SHOCK, OR OTHER INJURY OR DAMAGE.
WATCH FOR SMALL PARTS.
The device and accessories may present a choking hazard to small children and
pets. Keep them out of reach of small children and pets.
WARNING : Electrical shock hazard. Disconnect power to installation area
at your circuit breaker or fuse box before beginning installation. Always use
caution when handling electrical wiring. Installation by a qualified
electrician may be required in your area. Refer to your local laws and
building codes before performing electrical work; permits and/or professional
installation may be required by law.
FIRE RISK : Do not mount near combustible or flammable surfaces. Your device is water resistant and is suitable for outdoor use. However, your device is not intended for underwater use. To protect against electric shock, do not intentionally submerge or immerse your device in water or expose your device to other liquids. Do not spill any food or beverages on your device. Do not attempt to clean or polish your device with or expose your device to oil, lotion, or other abrasive substances. Do not expose your device to salt water or other conductive liquids. Do not expose your device to pressurized water, high velocity water, or extremely humid conditions (such as a steam room). Do not attempt to dry your device with an external heat source, such as a microwave oven or a hair dryer. To avoid risk of electric shock, do not touch your device or any wires connected to your device during a lightning storm while your device is powered. If your device appears to be damaged, discontinue use immediately. Do not install on the ground. Your device should be installed outdoors to a wall or eave. To reduce the risk of fall, take extra caution when using a ladder or similar equipment to mount your device. Do not cover the device while operating. Do not open the hous-ing. Your device does not contain serviceable parts or replaceable LEDs. Protect this device from sunlight. Disconnecting the wires will power the device off. Do not use the device if the wires or housing are defective, there is a risk of electric shock. Do not cut any wires with factory installed wire connectors or remove the wire connectors. Do not install on circuits feeding motor loads such as kitchen appliances, HVAC equipment, washer/ dryer or garage door openers. Do not install when it is raining. Do not stare directly at the LEDs for more than a few seconds to avoid eye injury. Only use accessories that are recommended by the manufacturer. Use of third-party accessories may lead to damage to your device or the accessory and may cause fire, electric shock, or injury.
SAFELY CONNECTING YOUR RING FLOODLIGHT CAM WIRED PLUS TO YOUR HOME’S ELECTRICAL WIRING
You must turn off the power source to the electrical box at your home’s
circuit breaker or fuse and test that the power is off BEFORE removing an
existing floodlight or light fixture, installing the device, or touching
electrical wires. Failure to turn off circuit breaker or fuse could result in
FIRE, ELECTRIC SHOCK, or OTHER INJURY or DAMAGE. More than one disconnect
switch may be required to turn off the equipment before servicing. If the
electrical wiring in your home does not resemble any of the diagrams or
instruc-tions provided with the device, if you encounter damaged or unsafe
wiring, or if you are unsure or uncomfortable in performing this installation
or handling electrical wiring, please consult a qualified electrician in your
area.
Verify that the supply voltage is correct. Connect fixture to a 100 VAC~240
VAC 50/60 Hz power source. Properly ground fixture. Always install wiring
connections in accor-dance with local code standards.
Product Specifications
- Device Name: Ring Floodlight Cam Wired Plus
- Model Number: 5AT3T2
- Electrical Rating: Hardwired (110 to 240V)
- Temperature Rating: -5°F to 120°F (-20.5°C to 48.5°C)
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated. Make
sure you dispose of, or recycle, your device in accordance with your local
laws and regulations. For information about recycling your device, go to
amazon.com/devicesupport.
Terms of Service and Warranty
Use of the product is subject to your registration with Ring and your
agreement with the Terms of Service found at ring.com/terms To review your
warranty coverage, please refer to the enclosure inside this box or visit
ring.com/warranty
For Consumers in the USA
This device complies with Part 15 of the FCC Rules. Operation is subject to
the follow-ing two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installa-tion. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The device meets the FCC Radio Frequency Emission Guidelines. Information on the product is on file with the FCC and can be found by inputting such Product’s FCC ID (which can be found on the device) into the FCC ID Search form available at fcc.gov/oet/ea/fccid. The party responsible for FCC compliance is: Ring LLC, 1523 26th St. Santa Monica, CA USA, 90404
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>