Rock n Rollerskate 71203 Girl Lightning Luna Fashion Doll Instructions
- June 6, 2024
- Rock n Rollerskate
Table of Contents
INSTRUCTION GUIDE
CONTROLLER (71203TX & 71207TX): x3 1.5V AAA (LR03) ALKALINE BATTERIES REQUIRED
(INCLUDED)
RAINBOW RILEY (71203RX) / LIGHTNING LUNA (71207RX): x4 1.5V AA (LR6) ALKALINE
BATTERIES REQUIRED (NOT INCLUDED)
WARNING: This toy produces fashes that may trigger epilepsy in sensitized
individuals.
Adult Supervision Required. Always play in safe surroundings, away from
streets or moving vehicles.
Colors & decoration may vary. Retain packaging/instructions for reference.
Remove all packaging before giving the toy to a child.
WARNING! Small Parts. Choking Hazard.
Try Me Removal
- Using a Phillips head screwdriver (not included) remove the Battery cover on the DOLL and CONTROLLER and detach the wire on both.
- Push the power switch on the DOLL to the “OFF” position. Remove the DOLL batteries. Install fresh batteries in the DOLL and CONTROLLER and replace the battery covers on both.
(See BATTERY INSTALLATION).
The batteries included are for “Try Me” purposes only. If performance diminishes after purchase, replace with fresh batteries.
BATTERY INSTALLATION ADULT INSTALLATION REQUIRED
-
Locate the battery compartment on the bottom.
-
Using a Phillips Head Screwdriver (not included), remove the screw and battery door.
-
Controller – Install 3 new “AAA” batteries.
Doll – Install 4 new “AA” batteries. -
Replace the battery cover and the screw.
SAFETY INFO
R/C PAIRING
OPERATION
-
Please remove try me cable from DOLL and REMOTE CONTROL before use.
-
Pairing is required every time the DOLL/REMOTE CONTROL is turned ON.
-
Move ON/OFF/TRY-ME switch to the ON position on REMOTE CONTROL.
-
Move ON/OFF/TRY-ME switch to the ON position on DOLL.
-
Place the DOLL on the ground and point the REMOTE CONTROL at the DOLL. The LED light on the REMOTE CONTROL will flash when paired with the DOLL.
The pairing process is complete when the LED light is solid, then the DOLL is ready to go. -
Note: If the LED light on the REMOTE CONTROL is flashing; switch off both DOLL and REMOTE CONTROL and repeat pairing process.
-
Note: This doll is recommended for indoor use only. Works best on tile, hardwood floor, and other smooth hard surfaces.
Not recommended for use on carpets, grass, loose dirt, wet surfaces, or concrete. -
Never use in water or mud. Never use glass and other fragile objects.
CONTROLLER FUNCTIONS
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|
| Doll won’t move. | 1. Doll or Remote Control switch is switched OFF. |
2. Weak Doll batteries.
3. Weak Remote Control batteries.
4. Doll is stuck
5. Remote Control is not close enough to Doll.| 1. Move the switch to the ON
position.
2. Replace batteries.
3. Press any direction button. If the indicator light does not activate,
replace batteries in the Remote Control.
4. Move the doll to a smoother surface, clean the wheels, and make sure the
surface or floor is clean as well.
5. Make sure the Remote Control is placed within the signal receiving range.
BATTERY SAFETY INFORMATION:
WARNING! Battery acid leakage can cause personal injury and cause damage to the product and surrounding property. If battery leakage occurs, thoroughly wash any affected skin, making sure to keep battery acid away from eyes, ears, nose, and mouth. Immediately wash any clothing or other surface that comes in contact with leaked battery acid. Leaking batteries may make “popping” sounds. Always remove replaceable batteries before disposing of the product. Dispose of batteries or products with non-replaceable batteries according to Local, State, or Federal Battery and Recycling Laws.
TO AVOID BATTERY PROBLEMS:
NEVER mix old and new batteries or different brands of batteries.
NEVER mix alkaline, standard (carbon-zinc), rechargeable batteries with
this product.
NEVER dispose of batteries in fire, as they may leak and explode.
ALWAYS remove batteries when exhausted or unused for a long time.
ALWAYS have an adult install battery consistent with installation
instructions.
ONLY use batteries specified by the manufacturer.
Batteries are to be inserted with the correct polarity (+ and -).
The supply terminals are not to be short-circuited.
Non-rechargeable batteries are not to be recharged.
Rechargeable batteries are to be removed from the toy before being charged.
Rechargeable batteries are only to be charged under adult supervision.
The batteries included are for “Try Me” purposes only. If performance diminishes after purchase, replace with fresh batteries.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for Class B digital devices, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference including interference that may cause undesired operation of the device.