Hamilton Beach HBH550 3 HP Fury 64 oz. High Performance Bar Blender Instruction Manual
- June 4, 2024
- Hamilton Beach
Table of Contents
Beach HBH550 3 HP Fury 64 oz. High-Performance Bar Blender
Instruction Manual
FURY Series Bar Blender
Operation Manual (2)
www.commercial.hamiltonbeach.com
IMPORTANT SAFETY INSTRUCTIONS
WARNING – When using electrical appliances, basic safety precautions should be followed, including the following:
-
Read the Operation Manual before using a blender.
Keep Operation Manual handy. -
Before first use, wash container assembly in hot, soapy water. Do NOT place in dishwasher.
-
Plug into a grounded outlet.
-
Do not remove ground.
-
Do not use an adapter.
-
Do not use an extension cord.
-
Disconnect power before cleaning or servicing.
-
To reduce risk of personal injury, unplug the cord from the outlet when not in use, and before putting on or taking off parts.
-
Unplug the blender and inspect the power cord insulation for cracks on a weekly basis. Refer to “Technical Service” for repair or replacement.
-
To protect against electrical shock, do not immerse the cord, plug, or blender base in water or any other liquid.
-
Do not spray the base with a high-pressure spray gun.
-
Extreme caution must be used when moving an appliance containing hot oil or other hot liquids.
-
Do not use appliances for other than intended use.
-
Not intended for use by or near children.
-
Children should be supervised to ensure they do not play with the appliance.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
-
The use of accessory attachments not recommended by the appliance manufacturer may cause injuries.
-
To reduce risk of personal injury and to prevent damage to the blender or container and cutter assembly, DO NOT insert utensils into the blender container while operating the blender.
-
Do not store any kitchen utensils in the container because the blender would be damaged if inadvertently turned on.
-
To prevent the possibility of serious personal injury, keep your hands out of the blender container while operating the blender.
Always operate the blender with the container cover in place. -
Avoid contacting moving parts. Switch off the appliance and disconnect from the power supply before changing accessories or approaching parts that move in use.
-
Blades are sharp. Handle carefully.
-
If cutter assembly blades are loose, discontinue use immediately and replace the container. Do not attempt to repair or tighten the cutter assembly.
-
Inspect container and cutter assembly daily. Do not use broken, chipped, or cracked containers. Check the cutter for wear, nicks, or broken blades. Do not use broken, loose, or cracked cutting blades.
-
Do not use outdoors.
-
This appliance is intended for short periods of operation, with a rated operating time of 3 minutes.
-
Do not leave the blender unattended while it is operating.
-
To prevent damage to the blender, container, or cutter assembly, DO NOT move or shake the blender while in operation. If the blending action stops during operation, turn the blender OFF (O), remove the container from the base, remove the container cover, and use a thin rubber spatula to push the mixture toward the cutters.
-
When blending hot liquids, remove the center piece of the two-piece lid. Hot liquids may push lid off the jar during blending. To prevent possible burns: Do not fill the blender jar beyond the 1 quart (1 liter) level. With the protection of an oven mitt or thick towel, place one hand on top of the lid. Keep exposed skin away from the lid. Start blending at the lowest speed.
-
The blender is provided with a power switch/circuit breaker on the bottom of the unit. If the motor stops turning, reset the power switch.
-
This blender’s motor is provided with a thermal overload protector. If the motor stops turning during operation or will not restart, unplug it and allow to cool for 15 minutes. Plug the unit back into the outlet and resume operation.
-
The normal function of this product may be disturbed by strong electromagnetic interference. If this occurs, simply reset the product and resume normal operation by following the operation manual. If the normal operation cannot be resumed, place the product in a different location.
-
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Refer to “Technical Service” for instructions on examination, repair, or electrical or mechanical adjustment.
-
If the supply cord of this appliance is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person.
UK ONLY: If fitted with a non-rewirable U.K. plug, the 13 amp fuse approved by ASTA to be B.S. 1362 must be used. If you need a replacement fuse carrier, it must be replaced with the same color-coded carrier with the same markings. Fuse covers and carriers can be obtained from approved service agents.
| Electrical Shock Hazard
Disconnect the power before cleaning the blender base. Failure to follow these
instructions can result in death or electrical shock.
---|---
| Electrical Shock Hazard
Plug into a grounded outlet.
Do not remove the ground.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical
shock.
| Cut Hazard
Always place the cover on the container when blending.
Do not put hands, spoons, or other utensils in the container when blending.
Failure to follow these instructions can result in broken bones, cuts, or
other injuries.
| Burn Hazard
Always use caution when blending hot contents.
Failure to follow these instructions can result in burns.
Sanitizing
Sanitize using 1 tablespoon (15 ml) of household bleach per 1 gallon (3.8 liters) of clean, cool water (60°F/16°C), mixed according to the instructions on the bleach.
- Fill the container with sanitizing solution, replace the cover and filler cap and run on LOW (1) speed for 2 minutes. Empty container.
- Wipe the exterior with a soft cloth dampened with sanitizing solution.
- Immerse the cover and filler cap in sanitizing solution for 2 minutes.
- Place the empty container on the base and run on HIGH (2) speed for 2 seconds to remove any moisture from the cutter assembly.
- When ready to use, rinse with clean water.
Technical Service
For assistance or replacement parts, call our
Technical Service number:
++910-693-4277
www.commercial.hamiltonbeach.com
INSTRUCTIONS FOR PROPER DISPOSAL OF THIS PRODUCT PURSUANT TO THE EUROPEAN
UNION’S DIRECTIVE ON ELECTRICAL WASTE
Please do not dispose of any electrical equipment as ordinary waste. Help
conserve natural resources and protect the environment: when you have finished
using this product, please dispose of it at your local waste collection or
recycling center in the area reserved for electrical equipment. Contact your
local authority to find the nearest waste collection center. To remind you to
dispose of this product responsibly and separately from ordinary waste, it is
marked with the symbol of a crossed-out trash bin.
261 Yadkin Road
Southern Pines, NC 28387
www.commercial.hamiltonbeach.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>