Shenzhen Nkl Technology FE1 Smart Bracelet User Manual
- June 6, 2024
- Shenzhen Nkl Technology
Table of Contents
USER MANUAL
SMART BRACELET
Downloading the App
Scan the following QR code, download, and install the App.
http://plus.crrepa.com/app-download/dafit
Da Fit
Scan QR Code and Download
Charging and Active
Charging the device to act before the first time using; To charge your device,
plug the charging cable into the adapter or USB port on your computer.
Note: Do not use a USB charger with a current exceeding 1A Charge the
bracelet
Pairing
The MAC address on the “Setting”-“About” page could help you identify your device on the scanning list.
Use the Touch Screen
Phone Call
Connect to the bracelet through the phone’s Bluetooth to make and receive
calls
(Note: Other functions must be connected to the bracelet via APP (Da Fit)
to use).**
Points to note when using:
- If the bracelet has been connected by another mobile phone, please disconnect it from the original mobile phone first At the same time, the wristband end will restore the factory settings once in the settings.
- Please note that the Bluetooth name of the call connection is “Audio_ FE1 “, (This “Audio_ FE1 “, (This device must not be connected to a Bluetooth device named ” FE1″, otherwise it will appear when the APP is connected, and the search cannot be found here Problems with equipment).**
- Please do not leave the bracelet more than 5 meters away from the phone during a call, otherwise, the call quality will be affected.
In the mobile phone operation: settings-Bluetooth-search for “Audio_ FE1 ” after connecting You can dial or answer the call
SmartWatch Features
| Sleep
If you keep wearing Smart Watch in your sleep, it can provide the hours slept
and quality of sleep stats on both the screen and the APP.
NOTE: Sleep stats reset to zero at 8:00 pm.
---|---
| Heart Rate Test
The SmartWatch could record your heart rate all day.
You also could tap on the page to start measuring heart rate.
| Sports
Smart Watch automatically tracks Steps taken on the screen. NOTE: Your
movement stats reset to zero at midnight.
| Training
Tap the training icon on the menu to start a new training measure
recording, there are Multiple sports modes to be chosen.
The last training recording will be shown on the training page.
| Blood Pressure Test
Tap on the blood pressure page to start measuring your blood pressure.
On the blood pressure page, It can show the blood pressure measurement data of
the last times.
| Sp02 Test
Tap the Sp02 page to start measuring your Sp02. On the Sp02 page, It can show
the Sp02 measured data of the last times.
| Weather
It could show the weather info of current and tomorrow on the weather page.
Weather info is synced after connecting with the APP, it will not be updated
after a long disconnection.
| Messages Reminder
The device can sync incoming notifications from Twitter, Facebook, Whatsapp,
Instagram, etc. Recently 5 messages can be stored. Note: You can switch
off/off the incoming notification in the APR
| Remote Shutter
After connecting the device, you can remote control the camera on your phone.
| Player Shutter
After connecting the device, you can remote control the music player on your
phone.
| Other Features
Other features include a stopwatch, alarm, timer, brightness, mute on/off,
theater mode, factory reset, power off, and about.
| StopWatch
Tap the start button on the stopwatch page to start timing and tap the stop
button to stop timing.
| Silent Alarms
Set up the alarm on the APP, the device will vibrate to remind on time.
| Remind to Drink
The smartwatch will remind you of ‘Time to Drink Some Water” at the planned
drinking time. Note: You can set the feature in the APP.
| Remind to Move
The device will vibrate to remind you to make relax after 1-hour sitting.
Note: You can switch on/off the feature in the APP.
Frequently Asked Questions and Answers
-
If you need to play songs and answer calls through this bracelet, please go to the mobile phone-Settings-Bluetooth-Connect Audio_FEi Bluetooth name device
(If it cannot be used due to misoperation after a period of use, You can also repeat the following steps) -
If the device of Audio FE1 is not found, please confirm the When the Bluetooth switch is turned on
a. Please slide down on the top of the bracelet (top drop-down menu) -Confirm that the phone switch is “on” b. If necessary, if you can’t find it yet, please click on the wristband -Settings-Restore factory settings, then go back to step 1 Find the connected Bluetooth device named Audio F E 1 -
If the wristband is away from the phone for more than 3 minutes, To achieve low power consumption and enhance battery life, The bracelet will automatically disconnect from the phone. As shown in the figure below, it is displayed as “not connected”
-
At this time, please slide down on the top of the bracelet (Top drop-down menu) Click the switch to turn off a call, Tap the call again to change the status to “On” again, You can re-enter the connection state.
-
The bracelet will automatically connect with the phone again
-
Using in Wet Conditions
Your device is water-resistant, which means it is rain-proof and splash-proof and can stand up to even the sweatiest workout.
NOTE: Do not swim with your Smart Bracelet. We also don’t recommend showering with your wristband; though the water won’t hurt the device, wearing it 24/7 does not give your skin a chance to breathe. Whenever you get your bracelet wet, dry it thoroughly before putting it back on. -
Using Quick View
With Quick View, you can check the time or the message from your phone on your Smart Bracelet without taping. Just turn your wrist towards you and the time screen will appear for a few seconds. -
Environmental Conditions
Operating temperature: 14°F to 122°F (-10°C to 50°C) Non-operating temperature: -4°F to 140°F (-20°C to 60°C) -
Size
Fits a wrist between 5.5 and 7.7 inches in circumference. -
Disposal and Recycling
Please kindly be aware that it is the consumer’s responsibility to properly dispose and recycle Smart Bracelet and accompanying components. Do not dispose of Smart Bracelet with common household waste, the Smart Bracelet unit is considered electronic waste and should be disposed of at your local electronic equipment collection facility. For more information, please contact your local electronic equipment waste management authority or the retailer where you bought the product.
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.