woosim systems WSP-R350 3 Inch Mobile Printer Owner’s Manual

June 5, 2024
Woosim Systems

woosim systems WSP-R350 3 Inch Mobile Printer

All specifications are subjected to change without notice.

Copyright
WSP-R350 3inch mobile printer operator’s manual.
Copyright ⓒ2021 by Woosim Systems Inc.
All rights reserved.
The information contained in this manual is the property of Woosim Systems Inc.
And may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc.

Trademark
a registered trademark of Woosim Systems Inc.
All other trademarks are the properties of their respective companies.

Caution
Some semiconductor devices are easily damaged by static electricity. You should turn the printer “OFF”, before you connect or removed the cable on the rear side, in order to guard the printer against static electricity.
If the printer is damaged by the static electricity, you should turn the printer “OFF”.

Notice
The contents of this manual are subject to change without notice.
http://www.woosim.com

Introduction

The WSP R 350 is the ideal solution for Mobile banking systems, Retail, point of sales, Credit card Transaction, other traveling and mobile computing etc.

The general features of WSP-R350 printer are as follows:

  • Pocket size (108.5 X 134.8 X 56.5mm)
  • Lightweight (397.5g) for true mobility.
  • Very silent printing thru direct thermal printing method.
  • High speed(120mm/sec, MAX)
  • High resolution(203dpi : 8dots/mm
  • USB, Bluetooth Ver3.0, UART(RS-232C or TTL) [option] Interface
  • Intuitive LED’s indicate Power(on/off),Error, Bluetooth status, Battery status
  • Support text and graphic printing.
  • Easier paper loading by CLAMSHELL design.
  • One-touch paper cover
  • Printer door open & Paper-out sensor
  • Easier maintenance with self-diagnostics.
  • In field programming – Update Firmware, Download Fonts and Logos
  • Microsoft Windows/Windows CE, Linux, Android, iOS compatible
  • Flow control: Software (XON/XOFF)
    Hardware flow control not supported in the printer.

Operating Precautions
Please follow the precautions below to enjoy and maintain the full performance of the printer.

Using the Printer

  • Be careful not to drop or bump the printer on a hard surface.
  • Do not install the printer in direct sunlight or such areas. A suitable environment for the use of the printer is as follows:
    • Operating temperature:-10°C to 50°C
    • Relative humidity: 30% to 80%
  • Do not install the printer near devices that generate strong electromagnetic fields such as a copy machine.
  • Do not open the platen cover during printing.
  • Do not remove or reinstall the communication cable during printing or transmission.
  • Do not touch the connectors of the communication during printing.
  • Switch the POWER OFF when not in use.
  • Do not use another solvent.
  • The AC adapter, the battery charger and the battery pack may become warm when in use. This is normal and is not a malfunction.
  • When the battery pack is used at low temperature, the length of time the printer can be used may be shortened.

Thermal Paper Handling

  • Store the thermal paper in a cool, dry and dark place.
  • Do not rub the paper with hard object.
  • Do not leave the paper with hard object.
  • Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods.
  • Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies.
  • Do not use chemical glue.
  • Always use clean thermal paper.

Federal Communications Commission

Radio Frequency Interference Statement
FCC ID : QDD-WSPR350
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.
    CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
    Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Modifications not expressly approved by the manufacturer could void the user’s authority to operated the equipment under FCC rules.
This Device has been evaluated to comply with RF exposure requirement for general use limit in portable condition. It is safe to be used in sold condition.

CE WARNING

  • Changes and modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  • It is desirable that it be installed and operated with at least 20cm or more between the radiator and person’s body(excluding extremities hand, wrists, feet, and ankles)

Outline

Modell cllassiifiicatiions

woosim systems WSP-R350 3 Inch Mobile Printer-4

Symbol


| Standby symbol

IEC 5009, the standby symbol(line partially within a broken circle), Indicates a sleep mode or low power state.

---|---
**| Direct current symbol**

This symbol is found on many electronic devices that either require or produce direct current.

Product Part Number System

woosim systems WSP-R350 3 Inch Mobile Printer-4

Example)

  1. Porti-S40 UART/Bluetooth Part No. ⇒ S40/A1
  2. Porti-SC30 Bluetooth Only Part No. ⇒ SC30/Z1
    Note) The above table is the interface format which is supported. But some of the interfaces are not supported according to the product and please contact us, if you have any questions regarding the interface.

Specifications

Item Specification
Printing method Direct thermal line printing
Character size – Font Size A: 12X24 / Font Size B : 9X24 / Font Size C

: 8X16

– KOR : 24X24(16X24)     /   CHN, JPN : 24X24

Characters per line| –   Font   A : 48cpl / Font  B : 64cpl / Font   C : 72cpl

–   KOR, CHN, JPN : 24cpl

Optional Characters| Alphanumeric:95, Extended Graphics:128X50 pages, International:10,

Simplified/Traditional Chinese, Japanese, Korean

Resolution| 203dpi, 8dots/mm
Print width| 3-inch (72mm, 576dots)
Printing speed| 120mm / sec (MAX)
Dimensions| 108.5 X 134.8 X 56.5mm

108.5 X 138.41 X 56.5mm (MSR Model)

Weight (w/o paper)| 397.5g  /   409.1g (MSR model)
Interface| USB, Bluetooth Ver3.0

UART(RS-232C or TTL) [option] interface

Paper supplied| Thermal roll paper, Label roll (80mm wide, 50ø)



Barcode supplied

| 1- dimension : UPC-A, UPC-E, EAN-8, EAN-13, CODE-39, CODE-93, CODE-128, ITF, CODABAR

2- dimension : PDF417, Micro PDF417, Truncated PDF417, QR-CODE, DATA Matrix, Maxicode

Etc :GS1 databar

Driver| Microsoft Windows, Linux
H/W spec.| MCU : RX-32bit, RAM : 128M bit, FLASH : 64M bit
Receive buffer size| 1M bytes
Sensor| Support Cover open, Paper, Label
MSR (option)| Triple tracks (1&2&3 Tracks Reading)

*Supports 3DES & AES encryption

Item Specification
Battery Rechargeable 7.2V DC, 2500mAh (Li-ion)
Battery duration 1 hour continuous printing
Battery Charger Input (100~240V AC 50~60Hz)

Output(8.4VDC/0.8A), 4hours full charge time

__

Environment Conditions

| Temperature| -10°C ~ 50°C (operating)

-10°C ~ 70°C (storage)

Humidity| 30% – 80% (operating)

10% – 90% (storage)

MCBF (Mean Cycle Between failure)| Mechanical| 37,000,000 lines
Head| Approximately 50 Km

Setting up the printer

Priinter & Accessoriies
Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance.

woosim systems WSP-R350 3 Inch Mobile Printer-5

OPTIONAL

Printer Features

Part Name

woosim systems WSP-R350 3 Inch Mobile Printer-7

Dimensions

woosim systems WSP-R350 3 Inch Mobile Printer-8

Replacing the paper roll

Note: Be sure to use paper rolls that meet the specifications.
Do not use paper rolls that have the paper glued to the core because the printer can not detect the paper end correctly.

  1. Make sure that the printer is not receiving data; otherwise, data may be lost.
  2. Open the paper cover as the “One-Touch” way by pressing the button in the arrow direction like the picture.
  3. Insert the paper roll as shown.woosim systems WSP-R350 3 Inch Mobile Printer-10
  4. Tear the excess paper off using the edge of paper door as a tear bar.
  5. To change paper width, move paper guide while pressing paper width change button as shown in the picture.

Power supplly

Internal power supply
The following specification is requested for Power supply.
Battery Charger : DC 8.4V/0.8A
Avoid using power supply which its power capacity of power current is extremely high.

Installing the Battery

Warning :

  • Before installing or removing the battery pack, ensure the printer is OFF.

  • If the printer is not used for long period of time, remove the battery pack from the printer.

  • Risk of explosion if battery is replaced by an incorrect type.
    Dispose of used batteries according to the instructions.

  • Batteries are provided not being charged. Please charge the battery before use.

  1. To install battery pack, proceed as follows:
  2. In sert the Battery Connector in the direction of the arrow.woosim systems WSP-R350 3 Inch Mobile Printer-13
  3. To remove battery pack, proceed the above order reverse.

Recharging the battery
For recharging the battery pack, install the battery pack in the printer.
Insert the Battery Charger to the charge connector of the printer.

NOTE:

  • While charging the printer, turn off the printer power.

  • Do not remove the battery during charging.

  • The battery is consumable parts and when purchasing, compared to the use hour gradually decreases. (Warranty 6 month)

  • If the printer is not used for a long time, unplug the power cord from the printer and outlet.

  • The recharging time depends on the voltage level and ambient temperature of the battery.
    Normally, if takes about 4 hours to recharge a battery pack.

  • You must use only the supplied adapter.

  • Red Lamp: charging the battery.
    Green Lamp: charging is finished.

Set operation mode
In keeping on pressing the Feed and Power button simultaneously until after the ERROR lamp blinks 5 times, the printer comes out at the circumstance to change the printer mode.
(refer to Table 2)

  • POWER button : use for changing OPTION status. (Error Lamp)
  • FEED button : use for changing MODE status. (Power Lamp)

Note
No additional mode settings are required to connect Android or iOS devices.

If you want to change the Bluetooth Mode of printer, you need to disconnect the Bluetooth function of the current paired Smartphone.

Methods :

  1. Turn off the Bluetooth function of the current paired Smartphone.
    (Blue LED is off.)

  2. Change the printer mode. (Additionally, we want to recommend you to rest(OFF→ON) the printer and change mode.)

woosim systems WSP-R350 3 Inch Mobile Printer-15

[Example] The defaults of the printer are :
USB / 9600 bps / 8 data bit / No parity / 1 stop bit / Density low/ Mark no use / Sensor low / Power down 5 minute
If a user wants to modify the defaults with
Bluetooth / 57600 bps / 7 data bit / Odd parity / 2 stop bit / Density high/ Mark use / Sensor medium1 / Power down no use

  • Press FEED & POWER Button during the Error Lamp flickers 5 times.

  • You will see the Power Lamp and the Error Lamp flickers once.

  • Press the POWER Button twice and the Error Lamp flickers 3 times.
    And then, interface mode has set to Bluetooth mode.

  • When you press FEED button once again, Power Lamp flickers twice and the Error Lamp flickers once.

  • Press POWER Button 3 times, Error Lamp flickers 4 times.
    And then, baudrate has set to 57,600 bps.

  • When you press FEED button once again, Power Lamp flickers 3 times and the Error Lamp flickers twice.

  • Press POWER Button once, Error Lamp flickers once.
    And then Data Bit has set to 7 data bit.

  • When you press FEED Button once again, Power Lamp flickers 4 times and the Error Lamp flickers once.

  • Press the POWER Button once, Error Lamp flickers twice.
    And then the Parity bit has set to the Odd parity bit.

  • When you press FEED Button once again, Power Lamp flickers 5 times and the Error Lamp flickers once.

  • Press POWER Button once, Error Lamp flickers twice.
    And then the density has set to 2 stop bit.

  • When you press FEED Button once again, Power Lamp flickers 6 times and Error Lamp flickers once.

  • Press POWER Button twice, Error Lamp flickers 3 times.
    And then the density has set to Density high.

  • When you press FEED Button once again, Power Lamp flickers 7 times and Error Lamp flickers twice.

  • Press POWER Button once, Error Lamp flickers once
    And then the mark has set to Mark no use.

  • When you press FEED Button once again, Power Lamp flickers 8 times and Error Lamp flickers once.

  • Press POWER Button once, Error Lamp flickers twice
    And then the sensor has set to Sensor medium1.

  • When you press FEED Button once again, Power Lamp flickers 9 times and Error Lamp flickers five times.

  • Press POWER Button once, Error Lamp flickers once
    And then the power down has set to Power down use.

If all the mode have set, press the POWER Button and the FEED Button at the same time after then release the buttons at the same time.

The printer will print out the mode status which has modified.
(Bluetooth / 57600 bps / 7 data bit / Odd parity / 2 stop bit / Density high /Mark no use / Sensor medium1 / Power down use)
If the status is not correct, please try it again according to the procedure.

woosim systems WSP-R350 3 Inch Mobile Printer-16

Notice : Bluetooth(iAP) is the mode which is used in iPod, iPhone and iPad Whole aspect.

Interface

UART(RS-232C or TTL) or USB

The WSP-R350 printer has a UART(RS-232C or TTL) or USB interface and is connected by means of a 5 pin mini USB socket.
In the following table, the signals present on the Mini- USB socket are listed:

UART

Pin No. Name Direction Function
1 TxD Output Transmit Data
2 RxD Input Receive Data
3 GND Ground
4 NC.
5 GND Ground

USB

Pin No. Name Function
1 VCC +5V
2 DM DATA “-”
3 DP DATA “+”
4 NC.
5 GND Ground

NOTE :

  • If you connect the printer interface cable is converted to UART or USB mode.
  • When data receiving, when it removes the communication cable, it loses a data.

Bluetooth

Category Specification
Bluetooth Spec. Bluetooth Ver3.0 / Class2 (10m)
Frequency band 2402~2480 MHz
Protocol L2CAP, RFCOMM, SDP
Profile GAP, SDAP, SPP

Using the printer

Control panel

woosim systems WSP-R350 3 Inch Mobile Printer-18

Button
  • FEED Button : Use feed button to feed the paper continuously.
  • POWER Button : This bu tton is used to power on/off.
    When of 5 or more seconds presses and power comes to on or off.

In keeping on pressing the Feed and Power button simultaneously until after the ERROR lamp
blinks 5 times, the printer comes out at the circumstance to change the printer mode.
(Refer to 2.6. Set operation mode for details about mode conversion)

LAMP

  • Power : Printer is ON and ready to receive data.
    (GREEN)

  • Error: Indicates a fault condition or a printer error.
    (RED) (details: no paper, paper cover opened. etc.)

  • Bluetooth: Indicates a Bluetooth connection status.
    (BLUE)

  • Battery Power: These lamps(Green) indicated the battery power remaining.
    (GREEN) The battery gain in quantity and these lamps are on the decrease.
    If so, you must recharge the battery by using the battery charger.

The self test
Self-Test prints out the current setting value of printer. The way of self- test is as follows.

  1. Insert proper paper into the printer.
  2. Power on while pressing feed button to start self-test.
  3. Printer will print out the current status. (F/W version and set contents)
  4. And then pattern of characters will be printed out.
  5. Self-test will be finished automatically and turned to standby status.

In case printer does not work properly, please contact Woosim customer service center.

Using the Bellt clip

woosim systems WSP-R350 3 Inch Mobile Printer-19

Following the instruction of the arrow, please put the belt clip in the hole and turn and fix the screw to the right by using a thing like a screwdriver.
Afterward, you can use it like the picture below

Consumable Parts

Recommended paper

  • Type: Thermal Paper
  • Paper width : 80mm
  • Paper thickness: 60±5㎛
  • Outer diameter : Ø 5 0 mm or less
  • Recording side: Outside of roll

Cautions

  1. Do not paste the paper to the core. And the roll paper which has Near-end mark printing on its near end is recommended.

  2. Chemicals or oil may change the color of paper, or printed Characters may fade.

  3. Change of paper color starts from approx 70 ℃.
    Pay attention to heat, humidity and sunlight.

  4. Color of paper may be changed by being scratched by nail or hard metal, etc

Printing position

woosim systems WSP-R350 3 Inch Mobile Printer-21

Revision History

Date Version Comments
Oct. 20. 2014 1.0 Initialize

Jul. 15. 2015

| ****

1.1

| p3,7,24 Bluetooth spec. update

: Ver2.1+ EDR → Ver3.0+ EDR

p8,14    Dimension(MSR) modify

p16     Mode setting modify(Android or iOS)

Sep. 21. 2015| 1.2| p3,8     Print speed modify

: 80 → 120mm/sec




Nov. 03. 2015

| ****



1.3

| p3 p5 p7 p10 p11 p17 p25


p28

| Agency approvals update Additional CE warning

Additional Symbol(standby, DC current) Battery charger spec modify

Battery charge & interface cable image modify Additional battery warnings

Bluetooth spec. modify Card read image update

Using the belt clip image update

Jul. 01. 2016| 1.4| p17

p25

| Additional battery charging Notes

Read a magnetic card image update

May. 18. 2017| 1.5| Change page layout (B5→A4)

  • Delete address

Mar. 04. 2019| 1.6| p3

p21

| CE mark modify

Note modify

Jun. 26. 2019| 1.7| p11,24| Belt clip image change
Jun. 16. 2020| 1.8| p10

p11,18

| Battery capacity : 2200mAh → 2600mAh

Battery charger adaptor image change

Dec. 13. 2021| 1.9| p10| Battery capacity : 2600mAh → 2500mAh

http://www.woosim.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals