Phonocar VM022 DAB+ Car Radio Instruction Manual
- June 6, 2024
- Phonocar
Table of Contents
Phonocar VM022 DAB+ Car Radio
Warnings
Installation to be carried out by trained technical personnel
- Make sure you have 12V DC, with negative-pole to mass
- First disconnect negative-pole of the car-battery, then effect car-radio connections When replacing fuse, always use fuse with same Ampere-value
- Never open the unit, nor try to repair yourself. Always ask your Retailer or authorized technical staff
- Make sure that no foreign objects fall into the unit, they would cause malfunctions, short-circuits or exposure to dangerous laser-rays
- When switching-on, make sure that temperate inside passenger-compartment is at a normal level
- Choose a listening-Volume which will allow you to hear external noises (car-horn, sirens etc.)
- When placing the cables, keep away from all car security-devices.
Connections.
Functions
Settings
AUDIO
Briefly press the VOLUME KNOB (4) to enter the menu of audio settings and
briefly press again. the knob (4) to scroll through the list of available
audio settings:
BASS-TRE (high/low tone adjustment)
BAL L-R (balancing)
FAD F-R (fader)
LOUD ON/OFF (loudness)
EQ (EQ OFF, ROCK, FLAT, CLASS, POP)
To adjust, turn the knob to the requested value.
GENERAL SETTINGS
Press the knob (4) for 3 seconds to enter the menu of generic settings and
briefly press the knob (4) again to scroll through the list of available
generic settings:
COLOUR (auto/blue/green/red/light blue/yellow/violet/white)
BEEP (on/off)
CLOCK (24/12)
P VOL (default base volume)
LOC (on/off – local/distance)
STEREO/MONO.
To adjust the wished setting, turn the VOLUME KNOB (4) to the requested value.
CLOCK 24/12
Set the time in 24-h or 12-h version
CLOCK
Press the DISP/0 (13) key several times until the time is shown on the
display.
Press the DISP/0 (10 key for 3 seconds, the time will begin to flash. Set the
desired time by rotating the VOLUME KNOB (4), then briefly press the volume
knob (6) and turn it to adjust the minutes, then press again to confirm. When
the time stop flashing, the setting is complete.
P.VOL
This function sets the volume level at the power on.
DX/LOC (Distant/local)
LOC ON: Reduces the sensitivity of radio reception when searching for
stations, so only stations with a good signal are found.
LOC OFF: The sensitivity of the radio reception is at its highest level and
all the stations will be found, both with good and poor signal.
Radio e DAB+ functions
SELECT RADIO SOURCE
Briefly press the “BAND” key (8) to select: FM1 – FM2 – FM3 – MW1 – MW2.
Press the (1)-(25) keys briefly to start the automatic search for the previous
station ( ) (1) or for the next one ( ) (25). Press the (1)-(25) key for two
seconds to start the previous station manual search ( ) (1) or the next one (
) (25). Press keys 1 to 6 for 3 seconds respectively for storing the station
on one of the 6 available memories. Select DAB source. The first time you
install the device,the scanning of the available DAB channels will start
automatically. Press the AS/PS (15) key to start an automatic channel scan
whenever you want. Briefly press the “ BAND” (8) key to select: DAB1, DAB2,
DAB3. Briefly press the keys to select the previous ( ) or next ( ) station
Press keys 1 to 6 for 3 seconds respectively for storing the station in one of
the 6 memories available.
USB – SD Card functions
When a USB or SD CARD is introduced, the audio tracks playback of the device in, will start automatically.
Press the keys ( ) briefly to switch to the previous / next track . Press and
hold the keys ( REWIND and FOWARD functions.
Briefly press the 1/ (22) key to pause a track, and press it again to restart
it-
Briefly press the 2/INT (21) key to enable/disable track input.
Briefly press the 3/RPT (20) key to enable/disable the automatic track
replaying.
Briefly press the /RDM (19) key to enable/disable the random playback
function.
Press and hold the 5/DIR- – 6/DIR+ (18-17) keys to switch between to the
previous / next folder.
AUX-IN functions
The VM022 allows external audio sources to be connected to the input (12) via
a 3.5 mm jack cable. Audio tracks are managed from the external source.
Telephone Bluetooth
Enable the Bluetooth on your phone, select the device named CARKIT enter the
password 0000 and confirm. To answer a call, press the key (15) and to end the
call, press the key (14).
Press and hold the (14) key to:
- Display received, missed, rejected calls. *
- Set the automatic or manual connection.*
- Set AUDIO BT.
Audio Bluetooth
For listening to audio files, check whether your phone is compatible with A2DP
protocol. Select the source BT MUSIC.
To start playing the file list in memory on your phone, press the1/ (22) key.
Press the (1)-(25) keys briefly to switch to the previous/next track.
Press and hold (1)-(25) keys for functions REWIND and FORWARD.
Briefly press the 1/ (22) key to pause a track, and press it again to restart
it.
Technical Data
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>