AIRSEE DR-203C Portable Electric Nail Drill User Manual
- June 6, 2024
- AIRSEE
Table of Contents
AIRSEE DR-203C Portable Electric Nail Drill
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE USING.
Please be sure to read the safety instruction as follow to avoid potential
hazards that could result in personal injuries or damage to the device.
Note: If the USB cable connects to the adapter, it is recommended to use
an adapter of 5V 2A. Please do not exceed 5V 2A, or the drill will burn out.
Check before Using
Check the power supply cord before the first use and during the life of the
device. Do not use this device if it has a damaged cord or it is not working
properly or damaged. fl, Do not plug this device into a voltage system that is
different from the voltage system specified on the device. Use with improper
voltage will damage the device and VOID warranty.
DI Please use the original cord only.
NOT IN USE
- Do not draw out the connecting wire during use or touch the cord with the wet hand to prevent electric leakage and shock or fire. Please turn the power off after use.
- Do not use the crooked or damaged nail drill bit or replace the bit when the power is on.
- Bl Adjust the speed gradually, not abruptly. Please stop to use once the unusual movement and noise happens.
- Misuse, dropping or excessive force may cause device damage. II Children under 18 years of age should not use this device
Maintenance Work
- Do not disassemble the device.
- Doing so could be dangerous and constitutes voiding warranty conditions. fl, Do not keep the device in a place which is about or more than 50°C(in a metal box, car or other places in high
- temperature). Keep the device dry and keep it away from the oil and grease.
- Store the device in a cool and dry place. Do not store it in a hot or humid environment.
- Keep electrical cord away from heated surfaces.
- Do not dispose of the device in heat or fire.
- Do not clean the device with harmful chemicals or detergents.
service@airseelife.com
SIX DRILL BITS
HOW TO USE
- Insert the drill bit firmly into the drill.
- Connect the nail drill power cord. The sliding switch on the power cord turns the drill on and off.
- Move the switch up or down to choose the direction of spinning.
- Slide the speed controller to accelerate or decelerate the rotation speed.
- After the polishing is finished, please turn off the machine by returning the control switch to the middle position.
Problem and Terms of Settlement
| Misoperation | Causing | Terms of settlement |
|---|---|---|
| Changing the nail drill bit | Turn off the power when | |
| when the power is on |
1. Motor burns out
| changing the nail drill bit
|
When not in use, the| 2. Bearing damages|
speed is adjusted to| (Loud Noise)| Turn off the power when
the minimum, and the power is on| | not in use
| |
The continuous working
| | time should not be too
Long time, Large load
work
| 1. Motor burns out
2. Device lifespan shortens
3. Bearing damages (Loud Noise)
| long when the working condition is in heavy load. When the device is
overheating, it should be
| | stopped immediately to
| | make it return to normal
| | temperature
Misoperation
| Causing|
Terms of settlement
---|---|---
Insert into a mismatched power cord
|
1. Motor burns out
| According to the device voltage requirements, insert the matching power
cord
Put the power cord at
random/ Pull the power cord
| 1. Power cord brokes
2. Poor connection
|
Do not pull the power cord
Replace the original cord randomly| 1. Motor burns out
2. Easy to cause short circuit
| Use the original specification cord
Dust into device/ device drops to the ground or by other impacts
|
1. Bearing damages (Loud Noise)
2. Motor gets hot
3. Rotational speed slows down
| Clean dust, add the dust-proof protection of the dustproof hood/ Avoid device drops or by other
impacts
Insert the nail drill bit into the device incorrectly
|
1. Drill bit falls out
2. High vibration
3. Drill bit stucks
| Insert the nail drill bit into the device correctly/ If the drill bit stuck, please try to take
it out hard
The size of drill bit is not suitable| Can not insert the drill bit into the device|
Use standard drill bit
Water int o the
device / Operate in wet or
moist conditions/Use a wet cloth to clean the device
|
1. Motor burns out
2. Device lifespan shorten s
| Do not operate in wet or moist conditions/ Only a dry cloth is allowed for
cleaning
SPECIFICATION
EMIAL:service@airseelife.com
WEBSITE: www.airseelife.com
WARRANTY AND CUSTOMER SERVICES
AIRSEE offers a 6-month limited warranty on quality-related issues. Please apply for your extra 6-month warranty extension and download the user manual in other languages by registering on www.airseelife.com if needed. Received the product
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>