JBL BassPro Hub 11 Inch Powered Subwoofer System Owner’s Manual
- June 6, 2024
- JBL
Table of Contents
BassPro Hub 11 Inch Powered Subwoofer System
Owner’s Manual
JBL BASS PRO HUB
THANK YOU FOR YOUR PURCHASE …
Your JBL product has been designed to provide you with the performance and
ease of operation you would expect from JBL.
- Please take time to read your owner’s manual in its entirety before operating or installing your subwoofer.
- Keep the owner’s manual for JBL BassPro Hub in your glove compartment along with the owner’s manual for your car.
- Put your subwoofer sales receipt with other important documents in order to expedite warranty service if needed.
ABOUT THE MANUAL
This manual describes general installation guidelines and operation
instructions. However, please note that proper installation of mobile audio
and video components requires qualified experience with mechanical and
electrical procedures. If you do not have the knowledge and tools to
successfully perform this installation, we strongly recommend
consulting an authorized JBL dealer about your installation options. Keep all
instructions and sales receipts for reference. Consider this manual as an
indispensable feature
of your subwoofer.
What’s in the box:
- 1x JBL BassPro Hub
- 1x wiring harness
- 1x vehicle mounting post
- 1x remote controller with 16-2/5″(5m) cable
- 1x Owner’s manual
INSTALLATION
IMPORTANT: Disconnect the vehicle’s negative (-) battery terminal before
beginning the installation.
NOTE: You may find it more convenient to make all of the connections to the
amplifier base before you permanently mount it.
MOUNTING THE BASSPRO HUB
The BassPro Hub mounts inside the rim of the spare tire in your trunk. To
mount the BassPro Hub properly, follow these steps:
- Remove the vehicle’s spare mounting post.
- Make sure that the spare tire is placed in the trunk with the outside of the tire facing downwards; the back of the rim should be facing you. This will ensure sufficient mounting depth for the BassPro Hub.
- Carefully place the BassPro Hub inside the rim of the spare tire.
- Insert the BassPro Hub mounting post into the slot in the center of the BassPro Hub. When it reaches the spare tire mounting bracket, begin turning clockwise to thread
the post into the bracket and tighten. Some applications require the use of the included adapter to provide a threaded slot for the mounting post.
NOTE: To keep from damaging the BassPro Hub or the spare tire rim, do not overtighten the mounting post.
BASSPRO HUB INPUT PANEL
You’ll make all wiring connections at the panel on the right side of the
BassPro Hub. To access the panel, remove two screws securing the cover on the
top panel of the BassPro
Hub, then lift off the cover (see illustration below).
1. POWER AND PROTECT INDICATORS
The PWR indicator will illuminate when the BassPro Hub is receiving power and
signal, and playing normally. The PRT indicator will illuminate if the amp
enters Protect mode in the event of conditions such as over/under voltage,
short circuit, amplifier output circuit failure, or excessive heat.
2 & 3. REMOTE INPUT AND BASS PRO HUB REMOTE **CONTROLLER
Sound controls for the BassPro Hub are all adjusted using the included remote
controller. Start by plugging the remote controller (3.) into the REMOTE input
(2.) on the BassPro Hub.
4 & 5. INPUT/POWER TERMINAL AND WIRING HARNESS**
Plug the included wiring harness (5.) into the INPUT/POWER terminal (4.) of
the BassPro Hub.
- FOR POWER, connect the red power wire from the harness to your vehicle’s+ (positive) battery terminal. You must also install a fuse holder with a 40A fuse in-line and within 18″ of the battery.
- FOR GROUND, connect the black ground wire from the harness a solid, metal point on the vehicle’s chassis using a ring terminal. Use sandpaper to clean the paint from the metal surface at the chassis location. Use a star-type lock washer to secure the wire.
- FOR REMOTE TURN-ON , connect the blue wire from the harness to the remote output wire on your head unit, if it has one, and if you’re using the line-level inputs.
LINE-LEVEL SIGNAL INPUTS
If your head unit has a subwoofer output, connect to the line-level inputs of
the BassPro Hub wiring harness using an RCA cable.
SPEAKER-LEVEL SIGNAL INPUTS
If your head unit only has speaker-level outputs, splice into its left and
right speaker wires (front or rear), then connect the spliced wires to the
corresponding L+, L-, R+, and R- wires on the BassPro Hub harness. Splice taps
are not included.
Important: Some factory-installed audio system amplifiers include
electronic filters that limit the amount of bass sent to the system’s smaller
speakers. This filtering will adversely affect the performance of the BassPro
Hub. To get the most bass possible from your subwoofer, splice the high level
harness into the factory system speaker outputs that are connected to the
system’s largest speakers (the ones designed to reproduce the most bass).
FUSE
If necessary replace the fuse with one of matching amperage: 30A.
USING THE REMOTE CONTROLLER TO ADJUST AUDIO SETTINGS
SETTING THE GAIN
Adjusting the gain lets you match the input sensitivity of BassPro Hub with the output of your receiver, and match the relative volume to the rest of the speakers in your vehicle.
- Start with gain control set to minimum, and the cross ver control and bass control rotated midway.
- Choose music with substantial bass content and turn the volume control on your receiver to %% of its total output.
- Adjust the gain control clockwise, listening carefully to the bass output. If you hear distortion, turn the gain control counterclockwise to decrease the gain.
ADDING BASS BOOST
Adjust the bass-boost control clockwise or counterclockwise to suit your taste. You can add up to + 12dB of low frequency boost.
SETTING THE CROSSOVER
Adjust the crossover control by turning the low-pass filter dial until the BassPro Hub plays only low-frequency information – yOU should not hear elements such as vocals coming from the woofer.
SETTING THE SUBWOOFER PHASE
The phase button lets you choose the setting – 0° or 180° that provides the cleanest bass output. Press the button in for 180°, and leave the button unpressed for 0°. Press and unpress the button to determine which setting works best in your system.
SPECIFICATIONS
- Amplifier Power: 200W RMS (2 ohms)
- Frequency Response: 30Hz – 150Hz
- Fuse:30A
- Maximum Current Draw: 30A
- Quiescent Current Draw: <1.2A
- Crossover Frequency: 50Hz – 150Hz
- Crossover Slope: 24dB/Octave
- Bass Boost: 0-12dB Variable @ Fix 50 Hz
- Line level input sensitivity: 0.2 V-4V
- Speaker level input sensitivity: 0.5V- 10V
- Dimensions (D x H): 14-3/16″ 6-1/2″ (360x164mm)
HARMAN International Industries,
Incorporated 8500 Balboa Boulevard,
Northridge, CA 91329 USA
www.jbl.com
© 2018 HARMAN International Industries, Incorporated. All rights reserved.
JBL is a trademark of HARMAN International Industries, Incorporated,
registered in the United States and/or other countries. Features,
specifications and appearance are
subject to change without notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>