OpenEye OE-C1011D4 4MP Indoor Micro Dome Camera User Guide
- June 6, 2024
- OpenEye
Table of Contents
OE-C1011D4 4MP Indoor Micro Dome Camera
37409AD
User Guide
openeye.net
This quick start guide provides only basic information on the camera’s settings and operation for initial installation. Please read the user manual for optimal camera configurations.
CONTENTS
Optional Free Paintable Dome Cover
This camera has an available paintable dome cover allowing it to be quickly
converted to a black housing or allow the custom painting to match its
installation environment. To reduce waste it is not included in every package
but may be requested free of charge at the time of purchase.
INSTALLATION
- Apply template sticker to the desired camera location.
- Use a 6mm drill bit to drill anchor holes as indicated on the mounting template.
- Remove the mounting template.
- Insert anchors.
- Mount camera.
- Connect the network cable.
- Adjust camera view.
- Secure lid/dome.
POWER
This camera is compatible with 12vDC and Power over Ethernet (PoE). If you are connecting 12vDC power, verify the polarity of the power connection.
DEFAULT USERNAME AND PASSWORD
NOTE: OpenEye IP cameras ship without a default password.
The admin user password can be set using the following methods:
-
OpenEye recorders running Apex 2.1 or newer will automatically set a new unique password if:
• Connected to an M-Series recorder with a built-in PoE switch.
• Connected to a network switch through the camera network port and selected then added in setup, if a new password has not already been set. -
Connect to the camera directly through a Web Browser and follow the onscreen prompts.
-
Use the Network Camera Manager (NCM) Utility.
Username: admin
NOTE: The NCM software manual can be found at https://www.openeye.net /ncm-manual
NOTE: Refer to your Apex recorder manual or quick start guide for instruction on adding cameras. Passwords must be 9-32 characters including at least two elements of the following three: digits, letters, and special characters.
ASSIGNING AN IP ADDRESS
OpenEye IP cameras are set to DHCP by default. If a DHCP server is not
detected after 2 minutes, the camera will default to IP address 192.168.51.2.
If you are not using a DHCP server, NCM will allow you to batch confi sure a
static IP address.
The IP address for the camera network on your Apex recorder is 192.168.51.1.
NOTE: To change this IP address please refer to your Apex recorder manual.
Selecting multiple cameras and entering IP address 192.168.51.2 will set an IP address on all selected cameras, starting at 192.168.51.2 and increasing per camera.
- Open Network Camera Manager.
- Select the applicable camera(s).
- Input starting IP address, Subnet Mask, Gateway, DNS.
- Apply changes.
- Wait 60 seconds before refreshing NCM.
CONNECTING TO THE IP CAMERA
To access the camera setup menu, you need to open the Network Camera Manager (NCM) utility. NCM is preinstalled on all OpenEye Recorders and is also available for download on the OpenEye website for installation on your personal computer or laptop.
- Open Network Camera Manager.
- Locate your camera on the Network Camera Manager list.
- To open the web browser, select the camera and click LOAD.
Camera
Maximum Resolution| 2592×1520
Frame Rate at Maximum Resolution| 30FPS @ H.264
Total Streams| 2 simultaneous streams
ONVIF| Profile S / G Compliant
Wide Dynamic Range| True WDR @ 4MP
Environmental and Power
Power Consumption| 5.5W Max
Input Voltage| 12vDC / 24vAC / PoE
Pan / Tilt / Rotate| Pan: 3° ~ 360°
Tilt: 0° ~ 68°
Rotate: 3° ~ 360°
CONNECTIONS
| 1 | RJ-45 | – | For network and PoE connections |
|---|---|---|---|
| 2 | Power (12vDC / | ||
| 24vAC ) | 1 | 12vDC + | |
| 2 | GND – | 24vAC2 | |
| 3 | Reset Button | _ | To restore the camera to factory defaults: |
1. Disconnect power for 30 seconds.
2. Reconnect power and wait 30 seconds.
3. Press and hold the reset button for 20 seconds.
4| Alarm & Audio I / 0| 1| Audio Out +| Audio connection
2| GND| Ground connection
3| Audio In +| Audio connection
4| GND| Ground connection
5| Alarm Input| Alarm connection
6| GND| Ground connection
7| Alarm Output| Alarm connection
8| Alarm Output| Alarm connection
5| Built-in Microphone| –| Audio In
6| microSD Card Slot| –| Insert the microSD card into the slot to store videos
and snapshots
Liberty Lake, WA, USA
509.232.5261
Copyright ©2021
OpenEye.
All Rights Reserved. Information contained in this document is subject to
change without prior notice. OpenEye does its best to provide accurate
information but cannot be held responsible for
openeye.net
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>