OpenEye OE-C3012T4 4MP Autofocus Turret Camera User Guide

June 6, 2024
OpenEye

OpenEye OE-C3012T4 4MP Autofocus Turret Camera

CONTENTS

OE-C3012T4 Turret Camera


Waterproof Cable Connector

|

Self-Tapping Screws & Plastic Anchors

Quick Start Guide

|

Mounting Template

INSTALLATION

Connect a network cable to the camera using the RJ45 input and connect the other end of the cable to your network switch or recorder.

  1. Apply template sticker to desired camera location.
  2. Drill anchor holes using included mounting template.
  3. Remove mounting template.
  4. Insert anchors.
  5. Mount camera.
  6. Connect network cable with included waterproof cable connector.
  7. Adjust camera view.

POWER

This camera is compatible with 12vDC and Power over Ethernet (PoE). If you are connecting 12vDC power, verify the polarity of the power connection.

ETHERNET CABLE CONNECTIONS

Connect a network cable to the camera using the RJ45 input and connect the other end of the cable to your network switch or recorder.

DEFAULT USERNAME AND PASSWORD

NOTE: OpenEye IP cameras ship without a default password.

The admin user password can be set using the following methods:

  1. OpenEye recorders running Apex 2.1 or newer will automatically set a new unique password if:
    Connected to an M-Series recorder with a built in PoE switch.
    Connected to a network switch through the camera network port and selected then added in setup, if a new password has not already been set.

  2. Connect to the camera directly through a Web Browser and follow the onscreen prompts.

  3. Use the Network Camera Manager (NCM) Utility.

Username: admin

NOTE: The NCM software manual can be found at https://www.openeye.net /ncm-manual

NOTE: Refer to your Apex recorder manual or quick start guide for instruction on adding cameras. Passwords must be 9-32 characters including at least two elements of the following three: digits, letters, and special characters.

ASSIGNING AN IP ADDRESS

OpenEye IP cameras are set to DHCP by default. If a DHCP server is not detected after 4 minutes, the camera will default to IP address 192.168.51.2. If you are not using a DHCP server, NCM will allow you to batch configure a static IP address. The IP address for the camera network on your Apex recorder is 192.168.51.1.

NOTE: To change this IP address please refer to your Apex recorder manual.

Selecting multiple cameras and entering IP address 192.168.51.2 will set an IP address on all selected cameras, starting at 192.168.51.2 and increase per camera.

  1. Open the Network Camera Manager application.
  2. Select applicable camera(s)
  3. Input starting IP address, Subnet Mask, Gateway, DNS.
  4. Apply changes.
  5. Wait 60 seconds before refreshing NCM.

CONNECTING TO THE IP CAMERA

To access the camera setup menu, you need to open Network Camera Manager (NCM) utility. NCM is preinstalled on all OpenEye Recorders, and is also available for download on the OpenEye website for installation on your personal computer or laptop.

  1. Open Network Camera Manager.
  2. Locate your camera on the Network Camera Manager list.
  3. To open the web browser, select the camera and click LOAD.

PRODUCT FEATURES

Camera

Maximum Resolution| 2688×1520
Frame Rate at Maximum Resolution| 30FPS @ 4MP H.264/H.265
Total Streams| Dual Streaming
ONVIF| Profile S / G / T Compliant
Day/Night| True Day / Night
Wide Dynamic Range| True WDR

Environmental and Power

Power Consumption| 8.16W maximum
Input Voltage| 12vDC / PoE
Pan / Tilt / Rotate| Pan: 0° ~ 360°
Tilt: 0° ~ 90°
Rotate: 0° ~ 360°
IP Rating| IP67

CONNECTIONS

1 RJ-45 For network and PoE connections
2 Power (12vDC)* Power connection

*12vDC power input port should be plugged when not in use.

1| Reset Button| To restore the camera to factory defaults:

  1. Disconnect power for 30 seconds.
  2. Reconnect power and wait 30 seconds.
  3. Press and hold the reset button for 20 seconds.

---|---|---
2| MicroSD Card Slot| Supports up to 512GB microSD card for Edge storage.
Do not add or remove the microSD card when the camera is powered on.

Waterproof Cable

1 Thread lock cap 4 Rubber “O” ring
2 Rubber plug 5 Camera cable
3 RJ45 enclosure

Liberty Lake, WA, USA 509.232.5261

Copyright ©2021 OpenEye.
All Rights Reserved. Information contained in this document is subject to change without prior notice. OpenEye does its best to provide accurate information but cannot be held responsible for typos or mistakes

Documents / Resources

| OpenEye OE-C3012T4 4MP Autofocus Turret Camera [pdf] User Guide
OE-C3012T4 4MP Autofocus Turret Camera, OE-C3012T4, 4MP Autofocus Turret Camera
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals