Infinix X659B HOT 10i Smartphone User Manual
- June 6, 2024
- Infinix
Table of Contents
Infinix X659B
User Manual (Av&Aw)
Explosion diagram specification
1 | FL(CTP+LCM) | 2 | REC DECO |
---|---|---|---|
3 | Front housing Assembly | 4 | Front CAM rubber |
5 | Front Camera | 6 | 21n1 receiver spk |
7 | LT sensor Seal rubber | 8 | FPC REC SPK |
9 | PCBA Main | 10 | Back CAM Conn foam |
11 | Fingertip | 12 | Back the main Camera |
13 | Back sub Camera | 14 | Sub Cam rubber |
15 | REC SPK con fb | 16 | Front cam con fb |
17 | UP frame asm | 18 | M1.4xL3.5 SCREW |
19 | Finger frame | 20 | M1.4L1.2D3.5 SCREW |
21 | 3in1 card holder | 22 | Battery cover asm |
23 | Side key | 24 | Back Cam Lens |
25 | M1.4xL3.5 SCREW | 26 | Down frame asm |
27 | Bat con rubber | 28 | Finger Con foams |
29 | LCM FPC con rubber | 30 | USB rubber |
31 | Side key FPC | 32 | Ear rubber |
33 | Battery | 34 | SUB PCBA |
35 | Coaxial cable | 36 | Moto |
Know your phone
- Front camera
- Volume + key
- Volume – key
- Power key
SIM/SD card installation
- Power off the mobile.
- Refer to the following picture for SIM / SD card installation.
Charging the phone
You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone).
- Please remind the front and back of the plug.
- Use only an INFINIX charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.
FCC Statement
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.`
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
SAR Information Statement
Your wireless phone is a radio transmitter and receiver. It is designed and
manufactured not to exceed the emission limits for exposure to radiofrequency
(RF) energy set by the Federal Communications Commission of the U.S.
Government. These limits are part of comprehensive guidelines and establish
permitted levels of RF energy for the general population. The guidelines are
based on standards that were developed by independent scientific organizations
through periodic and thorough evaluations of scientific studies. The standards
include a substantial safety margin designed to assure the safety of all
persons, regardless of age and health. The exposure standard for wireless
mobile phones employs a unit of measurement known as the Specific Absorption
Rate or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are
conducted with the phone transmitting at its highest certified power level in
all tested frequency bands. Although the SAR is determined at the highest
certified power level, the actual SAR level of the phone while operating can
be well below the maximum value. This is because the phone is designed to
operate at multiple power levels so as to use only the power required to reach
the network. In general, the closer you are to a wireless base station
antenna, the lower the power output. Before a phone model is available for
sale to the public, it must be tested and certified to the FCC that it does
not exceed the limit established by the government adopted a requirement for
safe exposure. The tests are performed in positions and locations (e.g., at
the ear and worn on the body) as required by the FCC for each model. The
highest SAR value for this model phone when tested for use at the ear is
0.429W/Kg and when worn on the body, as described in this user guide, is
0.225W/Kg(Body-worn measurements differ among phone models, depending upon
available accessories and FCC requirements). The maximum scaled SAR in hotspot
mode is 0.265W/Kg. While there may be differences between the SAR levels of
various phones and at
various positions, they all meet the government requirement for safe exposure.
The FCC has granted an Equipment Authorization for this model phone with all
reported SAR levels evaluated as in compliance with the FCC exposure
guidelines. SAR information on this model phone is on file with the FCC and
can be found under the Display
Grant section of http://www.fcc.gov/oet/fccid after searching on
FCC ID: 2AIZN-X659B Additional information on Specific Absorption Rates (SAR)
can be found on the Cellular Telecommunications Industry Association (CTIA)
website at http://www.wow-com.com. In the United States and Canada, the
SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged
over one gram of tissue. The standard incorporates a substantial margin of
safety to give additional protection for the public and to account for any
variations in measurements.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 10mm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS, and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
Operating System:Android
Android is a trademark of Google LLC.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>