Infinix HOT 40 Pro Smartphone User Manual
- June 1, 2024
- Infinix
Table of Contents
Infinix HOT 40 Pro Smartphone
Explosion diagram specification
| 1 | FL(CTP+LCM) | 2 | REC DECO |
|---|---|---|---|
| 3 | F HSG ASM | 4 | R CAM 108M |
| 5 | R CAM 8W | 6 | R CAM 2M |
| 7 | COAXIAL LINE | 8 | F CAM 32M |
| 9 | REC | 10 | MAIN FPCA |
| 11 | PCBA MB | 12 | SIM CARD HOLDER |
| 13 | PS RUBBER | 14 | PCBA COPPER B |
| 15 | PCBA COPPER A | 16 | MAIN WATERPROOF FRAME |
| 17 | R CAM CON FABRIC 8W | 18 | PCBA GRAPHITE FILM |
| 19 | MAIN WATERPROOF MYLAR | 20 | MI HOUSING |
| 21 | SCREW L3.5 | 22 | BAT COVER ASM |
| 23 | R CAM DECO PC | 24 | R CAM DECO PMMA |
| 25 | R FLASH DECO | 26 | R CAM RUBBER 8W |
| 27 | R CAM LENS 108M | 28 | R CAM LENS 2M |
| 29 | R CAM LENS 8W | 30 | SCREW L2.0 |
| 31 | USB RUBBER | 32 | EARPHONE RUBBER |
| 33 | R CAM FRAME 2M | 34 | PCBA COPPER C |
| 35 | MOTOR LINEA | 36 | SPK |
| 37 | BATTERY | 38 | FPC SIDE KEY |
| 39 | PCBA SUB | ||
| --- | --- | --- | --- |
Know your phone
- Front camera
- Volume + key
- Volume – key
- Power key & side fingerprint sensor
- NFC
SIM/SD card installation
- Power off mobile.
- Refer to the following picture for SIM / SD card installation.
Charging the phone
You can charge your device using a charger or by connecting it to the computer
using a USB cable (comes with the phone).
Use only INFINIX charger and cables. Other chargers or cables may damage the
device. This will invalidate your phone warranty.
FCC Caution
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Information to the user.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information
This mobile phone meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.60
W/kg averaged over one gram of tissue. Device types: Mobile Phone (FCC ID
:2AIZN-YYS-X6837) has also been tested against this SAR limit. The highest SAR
value reported under this standard during product certification for use at the
ear is 1.15 W/kg and when properly worn on the body is 0.79 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 1.0 cm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved antenna.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
Operating System：AndroidTM
Android is a trademark of Google LLC.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>