Infinix HOT 40 Smartphone User Manual

Infinix HOT 40 Smartphone

Specifications:

• Brand: Infinix
• Model: HOT 40 X6836
• Front Camera: Yes
• Side Fingerprint Sensor : Yes
• NFC: Yes

Product Usage Instructions

SIM/SD Card Installation:

1. Power off the mobile device.
2. Refer to the provided picture for SIM / SD card installation guidance.

Charging the Phone:

You can charge your device using the provided charger or by connecting it to a computer using the included USB cable. It is important to use only the INFINIX charger and cables to avoid damaging the device. The use of other chargers or cables may void the phone’s warranty.

FCC Caution :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including
  interference that may cause undesired operation.

Any changes or modifications not expressly approved by the responsible party could void the user’s authority to operate the equipment.

FAQ :

• Q: Can I use any charger to charge my Infinix HOT 40 X6836?
  • A: It is recommended to use only the provided INFINIX charger and cables to avoid damaging the device and invalidating the warranty.
• Q: How do I know if my Infinix HOT 40 X6836 has NFC?
  • A: The Infinix HOT 40 X6836 model comes with NFC capability. You can locate the NFC feature in the phone settings under connectivity options.

Explosion diagram specification

Know your phone

1. Front Camera
2. Volume + key
3. Volume – key
4. Power key & side fingerprint sensor
5. NFC

SIM/SD card installation

1. Power off mobile.
2. Refer to the following picture for SIM / SD card installation.

Charging the phone

You can charge your device using a charger or by connecting it to the computer using a USB cable (which comes with the phone).
Use only the INFINIX charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.

FCC Caution

Labeling requirements.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Information to user.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information:

This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaging over one gram of tissue.

Device type : X6836 (FCC ID: 2AIZN-X6836) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.00W/kg and when properly worn on the body is 0.55 W/kg.

Body-worn Operation

This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt clips, holsters, and similar accessories used by this device should not contain any  metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.

Operating System ： AndroidTM
Android is a trademark of Google LLC.

References

• Patents - DTS
• Patents - DTS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>