AUDIORANGE SATV001D Wireless Headphones User Manual
- June 6, 2024
- AUDIORANGE
Table of Contents
AUDIO RANGE SATV001D Wireless Headphones
User Manual
Earpanda Wireless TV Headphones
User Handbook
Product Details
Listening Modes
-
TV Mode
Turn headphones on. This is the default mode. -
Sound Amplification
Turn headphones on. Now press the “MIC”button.
Your headset will now use its internal microphone to act as a sound amplifier.
Quick Setup(1)
To Connect Audio Cable
Find your preferred audio jack and connect the associated cable from TV to
base.
Quick Setup(2)
If all ports on TV are taken:
Find your external TV box (cable box,satellite box,etc)
NOTES:
Please make sure only one audio cable is used every time;
Please make sure cables are firmly attached at both ends;
Best Keep TV Base away from home wifi devices.
Brief Technical Data
TV Base{transmitter):
Transmitting Frequency: 2.4GHz ISM GFSK
Transmitting Speed: 3M bps
Standby time: 600 seconds(no signal in)
Working Voltage: 5.1 ± 0.2V/1 000mA
Working Currency:60± 5mA
Standby Currency:40mA
Transmitting Distance: 30m(direct line distance without any obstacles)
TV Headphones{receiver):
Receiving Frequency: 2.4GHz ISM GFSK
Receiving Speed: 3M bps
Working Voltage: 3.7V (3.3-4.2V)
Standby Currency: 48± 1 mA
Working Currency: 50~65mA
Power Off Currency: <1A
Automatic Power Off Time: 300 seconds
Frequency Response: 20Hz~15KHz
Distortion: <1%
Signal Noise Rate: >70dB
Max Output Rate: 35~40mW
Sound Pressure Level: 128± 3dB SPL
Working Distance: 230m(direct line distance without any obstacles)
Problems and troubleshooting(1)
-
Why I can only hear static or nothing?
For all TV and internet TV with Dolby, please turn off Dolby.
If surround sound (5.1) is selected, try changing it to a non-5.1 option. -
Why I can not hear TV for my Netflix TV?
For Netflix TV, please adjust your streaming device’s audio output settings to Stereo or Linear PCM output. -
Why I can not mute the TV and hear from TV headphones?
To Mute TV and hear from headphones, you must make sure the TV base is connected with the TV directly, not through any TV box. -
Why do my TV headphones sound with noise, not clear at all?
Most likely the audio cable is not connected firmly.
please disconnect the audio cable and turn off the headphones, and connect again. -
Can I use more sets of TV headphones for more TVs at home?
sure, no problem.
You can get one set of TV headphones for the bedroom, and another set for the living room.
even if the two TV bases are very close, The headphones will work fine with each other.
Problems and troubleshooting(2) -
Why do I feel the headphones are too heavy after a long time of use?
To make sure the headphones long working time, we have used a high-quality Li- ion rechargeable battery.
we suggest users who feel heavy after a long time users can try to wear the headphones behind their heads. -
Why do I feel the headphones do not fit my head very well?
If your feel the headphones are not very fit, we suggest you press the arms of the headphone for some time to make their shape fixed. -
Why do my TV headphones affect my wifi so much?
They both use 2.4G technology, naturally, they will conflict with each other.
so we suggest you place the TV base away from home wifi devices. -
Why my headphones can not charge or can only charge in one charging slot?
Normally there is only one reason the headphones will not charge, their battery is full.
you can use the headphones some time and charge again.
As for why only charge in one charging slot, it is because the two charging slots have very small charging voltage differences. when the headphones’ battery is low, both charging slots can charge.
Shenzhen Soundaids Technology Co., Ltd.
www.soundaids.com
Earpanda® is our registered trademark shall you have any more questions or
suggestions, welcome to reach us at:
info@earpanda.com
info@soundaids.com
facebook.com/earpanda
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>