Verifone P630 Mobile Payment Device Instructions
- June 6, 2024
- Verifone
Table of Contents
Verifone P630 Mobile Payment Device Instructions
Power Packs
Before you connect the terminal power pack to an electrical outlet, check that the on/off power switch on the terminal is off. If the terminal does not have an on/off switch, check that the power cable connector is removed from the terminal’s power port. Or, when connecting the terminal to a power pack, always connect the plug of the power pack to an electrical wall outlet first. Then connect the power cable to the terminal’s power port. The reference input power ratings are as follows:
- Input Voltage: 100-240V AC, 50/60Hz
- Output Voltage: 12V DC, 1A
P630 is intended to be provided with a listed power supply module having an output rating of 12 VDC, minimum 1.0A, Tma 50°C, Class II and evaluated as a Limited Power Source or PS2 or equivalent.
Disconnecting Power
Disconnecting power during a transaction may cause transaction data files that are not yet stored in the terminal memory to be lost.
Location – Electrical Considerations
WARNING! This device contains sensitive electronic components that can be permanently damaged if exposed to excessive shock, electrical interference or vibration.
Equipment
Location – Environmental Considerations This device is for indoor use only. Do not plug the power pack into an outdoor outlet or operate the terminal outdoors. It is not waterproof or dustproof, and is for indoor use only. Any damage to the unit from exposure to rain or dust may void your warranty.
Do not use the terminal where ther is high heat, dust, humidity, moisture, or caustic chemicals or oils. Keep the terminal away from direct sunlight and anything that radiates heat, such as a stove or a motor. WARNING! Your POSterminal contains sensitive electronic components that can be permanently damaged if exposed toexcessive shock or vibration. To minimize the riskof damage to your terminal, avoid dropping your terminal and operating it in high-shock and high-vibration environments. Do not store the terminal where prolonged exposure to extreme temperature can occur, because it can cause permanent damage. Do not expose the terminal to water. Contact with water can cause this unit to malfunction.
- Repairs Do not, under any circumstances, attempt any service, adjustments, or repairs on this equipment. Instead, contact your local Verifone distributor or service provider for assistance. Failure to comply may void the product warranty.
- Damage Carefully inspect the shipping carton and its contents for any damage. If the unit or any product component appears damaged or to have been tampered with, immediately notify the shipping company and your Verifone distributor or service provider. Do not use a P630 unit that has been tampered.
- Cleaners and Solvents Never use thinner, trichloroethylene or ketone-based solvents to clean the P630 device, these may deteriorate plastic or rubber parts. Do not spray cleaners or other solutions directly onto the keypad or display. For best results, use a clean cloth damped with water and mild soap. To remove stubborn stains, use alcohol or an alcohol-based cleaner.
- Battery Pack/Coin Cell Dispose of the battery in accordance with all national, state, and local laws and regulations as regionally required. Some batteries may be recycled and may be accepted for disposal at local recycling centers.
CAUTION: There is risk of explosion if the battery is replaced by an incorrect type. Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion. Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas. A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
Notice for Operating Frequency and Output Power
- NFC: dB µA/m at 10 m
- 2.4G WLAN: 2400-2483.4(EIRP dBm) <20
- 5G WLAN: 5150-5250/5250-5350/5470-5725(EIRP dBm) <20 BT- EDR/LE (EIRP dBm) <10
FCC/IC Compliance
The following product has been tested and certified as compliant with the regulations and guidelines detailed below:
- Manufacturer: Verifone, Inc.
- Brand: Verifone
- Model: P630
Part 15 of FCC Rules and ITE/RF Notice This device complies with the
limits for a Class B digital device as specified in Part 15 of FCC Rules and
Innovation, Science and Economic Development Canada license-exempt RSS
standard(s). Which provide reasonable protection against harmful interference
in a residential installation.
This device complies with Part 15 of the FCC Rules and Innovation, Science and
Economic Development Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. In the unlikely event that there is interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
RF Exposure
USA
The product complies with the FCC portable RF exposure limit set forth for an
uncontrolled environment and is safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be keptas far as possible from the user body or setthe device to lower
output power ifsuch function is available. The SAR limit set by the FCC is
1.6W/kg for body worn SAR and 4W/kg for extremity SAR. Tests for SAR are
conducted using standard operating positions accepted by the FCC with the
device transmitting at its highest certified power level in all tested
frequency bands. This device complies with SAR for general
population/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and has been
tested in accordance with the measurement methods and procedures specified in
OET Bulletin 65 Supplement C. CE The P630 complies with the Radio Equipment
Directive (2014/53/EU) issued by the Commission of the European Community. A
minimum separation distance of 0cm must be maintained between the user’s body
and the device, including the antenna during body-worn operation to comply
with the RF exposure requirements in Europe for P630. A minimum separation
distance of 0mm is tested for Limbs SAR-10g/4.0W/kg criteria for P630.
CE Notice for WLAN For 5G Band (WLAN: 5150-5350 MHz) This device is restricted for indoor use only when operating in the 5150 to 5350 MHz frequency range.
This equipment may be operated in:
AT| BE| BG| HR| CY| CZ| DK| EE
FI| FR| DE| EL| HU| IE| IT| LV
LT| LU| MT| NL| PL| PT| RO| SK
SI| ES| SE| UK| IS| LI| NO| CH
TR| | | | | | |
Notice for Canada
- The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
- Where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.
Legal Terms and Conditions Regarding PCI SSC Approvals PCI SSC’s approval
only applies to PEDs identical to PED tested by a laboratory recognized by the
PCI Security Standards Council. If any aspect of the PED is different from
that tested by the laboratory, even if the PED is in accordance with the basic
product description contained in the letter, the PED model should not be
considered as approved, nor promoted as approved. For example, if a PED
contains firmware, software, or physical construction with the same name or
model number as those tested by the laboratory, butit is actually not
identical to the PED samples tested by the laboratory, the tethered should not
be considered or promoted as approved.
No supplier or any other third party may refer to a PED as “PCI Approved,” or
otherwise state or imply that the PCI SSC has approved, in whole or in part,
any aspect of a supplier or its PEDs, except to the extent and subject to the
terms and restrictions expressly set forth in a written agreement with PCI SSC
or in a letter of approval.All other references to PCI SSC’s approval are
strictly and actively prohibited by PCI SSC. When granted, approval is
provided by the PCI SSC to ensure certain safety and operational features
important to the achievement of the PCI SSC objectives, but the approval in no
way includes any endorsement or warranty regarding the functionality, quality,
or performance of any particular product or service. PCI SSC does not
guarantee any products or services provided by third parties. Approval under
no circumstances includes or implies product warranties by PCI SSC, including,
but not limited to, any implied warranties of merchantability, fitness for
purpose or non-infringement, all are expressly disclaimed by PCI SSC. All
rights and remedies regarding products and services, that have received
approval, must be provided by the party providing such products or services,
and not by PCI SSC or the payment brand participants.
Industry Canada Class B Emission Compliance Statement This Class B digital apparatus complies with Canadian ICES-003.
References
- Social Responsibility - Planet | Verifone
- Verifone | The Payments Architects Who Truly Understand Commerce