SAUBER WMTL-712 Washing Machine User Manual

SAUBER WMTL-712 Washing Machine

SAFETY INSTRUCTIONS

• Remove all packages and transport bolts before using the appliance. Otherwise, serious damage may result.
• The plug must be accessible after installation.

Risk of explosion!

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances( such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.) This may result in fire or explosion.
• Beforehand thoroughly rinse items of washing by hand.

Caution!

Installing the product!

• This washing machine is for indoor use only.
• It isn’t intended to be built-in using.
• The openings must not be obstructed by a carpet.
• Washing machine shall not be installed in bath room or very wet rooms as well as in the rooms with explosive or caustic gases.
• The washing machine with single inlet valve only can be connected to the cold water supply. The product with double inlet valves should be correctly connected to the hot water and cold water supply.
• Plug must be accessible after installation.
• Remove all packages and transport bolts before using the appliance. Otherwise, serious damage may result.

Risk of damaging appliance!

• Your product is only for home use and is only designed for the textiles suitable for machine washing.
• Do not climb up and sit on top cover of the machine.
• Do not lean against machine door.
• Cautions during Handling Machine:
  1. Transport bolts shall be reinstalled to the machine by a specialized person.
  2. The accumulated water shall be drained out of the machine.
  3. Handle the machine carefully. Never hold each protruded part on the machine while lifting. Machine door can not be used as the handle during the conveyance.
  4. This appliance is heavy. Transport with care.
• Please do not close the door with excessive forces. If it is found difficult to close the door, please check if the clothes are put in or distributed well.
• It is forbidden to wash carpets.

Operating the appliance!

• Before washing the clothes at first time, the product shall be operated in one round of the whole procedures without the clothes inside.

• Flammable and explosive or toxic solvents are forbidden.
  Gasoline and alcohol etc.Shall not be used as detergents.
  Please only select the detergents suitable for machine washing, especially for drum.

• Make sure that all pockets are emptied. Sharp and rigid items such as coin, brooches,nail, screws or stone etc. may cause serious damages to this machine.

• Please check whether the water inside the drum has been drained before opening its door.Please do not open the door if there is any water visible.

• Be careful of burning when the product drains hot washing water.

• Never refill the water by hand during washing.

• After the program is completed, Please wait for two minutes to open the door.

Packaging/Old appliance

This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal,recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the collection systems or contact the retailer where the product was purchased. They return and can take this product for environmentally safe recycling.

INSTALLATION

Product Description

Note!

The product line chart is for reference only, please refer to the real products as standard.

Accessories

1. Transport hole plug
2. Supply hose cold water
3. Drain hose (optional support)
4. Owner’s manual

Installation

Installation area

Warning!

• Stability is important to prevent the product from wandering!
• Make sure that the product should not stand on the power cord.

Before installing the machine, the location characterized as follows shall be selected:

1. Rigid, dry, and level surface
2. Avoid direct sunlight
3. Sufficient ventilation
4. Room temperature is above 0℃
5. Keep far away from the heat resources such as coal or gas.

Unpacking the washing machine

Warning!

• Packaging material (e.g. Films, Styrofoam) can be dangerous for children.
• There is a risk of suffocation ! Keep all packaging well away from children.

1. Remove the cardboard box and styrofoam packing.
2. Lift the washing machine and remove the base packing. Make sure the small triangle foam is removed with the bottom one together. If not, lay the unit down with side surface, then remove the small foam from the unit bottom manually.
3. Remove the tape securing the power supply cord and drain hose.
4. Remove the inlet hose from the drum.

Remove transport bolts

Warning!

• You must remove the transport bolts from the backside before using the product.
• You’ll need the transport bolts again if you move the , so make sure keep them in a safe place.

Please take the following steps to remove the bolts:

1. Loosen 4 bolts with spanner and then remove them.
2. Stop the holes with transport hole plugs.
3. Keep the transport bolts properly for future use.

Levelling the washing machine

Warning!

The lock nuts on all four feet must be screwed tightly against the housing.

1. Check if the legs are closely attached to the cabinet. If not, please turn them to their original positions tighten the nuts.
2. Loosen the lock nut turn the feet until it closely contacts with the floor.
3. Adjust the legs and lock them with a spanner, make sure the machine is steady.

Connect Water Supply Hose

Warning!

• To prevent leakage or water damage, follow the instructions in this chapter
• Do not kink, crush, modify or sever the water inlet hose
• For the model equips hot valve, connect it to hot water tap with hot water supply hose. Energy consumption will decrease automatically for some programs.

Connect the inlet pipe as indicated, There are two ways to connect the inlet pipe.

1. Connection between ordinary tap and inlet hose.
2. Loosen clamp nut and four bolts
3. Tighten clamp nut
4. Press slide bushing, insert inlet hose into connecting base
5. Connection finished
6. Connection between screw tap and inlet hose.
7. Tap with threads and inlet hose
8. Special tap for washing machine
   Connect the other end of inlet pipe to the inlet valve at the backside of product and fasten the pipe tightly clockwise.

Drain Hose

Warning!

• Do not kink or protract the drain hose.
• Position drain hose properly ,otherwise damage might result of water leakage.

There are two ways to place the end of drain hose:

1. Put it into the water trough.
2. Connect it to the branch drain pipe of the trough.

Note!

If the machine has • drain hose support, please install it like the following .

Warning!

• When installing drain hose, fix it properly with a rope.
• If drain hose is too long, do not force it into washing machine as it will cause abnormal noises.

OPERATIONS

Quick Start

Caution!

• Before washing, please make sure it’s installed properly.
• Before washing at first time, the washing machine shall be operated in one of the whole procedures without clothes in as follows.

Before Washing

1. Plug in
2. Open tap
3. Load
4. Add detergent
5. Close door

Note!

Detergent need to be added in “case I “after selecting pre-washing for machines with this function.

Washing

1. Select Programme
2. Select function or default
3. Start up

Note!

If default is selected, step 2 can be skipped.

After Washing

“End” on display.

Before Each Washing

• The working condition of the washer should be(0-40)℃.If used under 0℃,the inlet valve and draining system may be damaged. If the machine is placed under condition of 0℃ or less, then it should be transferred to normal ambient temperature to ensure the water supply hose and drain hose are not frozen before use.
• Please check the labels and the explanation of using detergent before wash. Use non-foaming or less-foaming detergent suitable for machine washing properly.
  • Check the label
  • Take out the items out of the pockets
  • Knot the long strips,zip or button
  • Put small clothes into the pillow slip
  • Turn easy-pilling and long-pile fabric inside out
  • Separate clothes with different textures

Warning!

• When washing a single clothes, it may easily cause great eccentricity and give alarm due to great unbalance. Therefore it is suggested to add one or two more clothes to be washed together so that draining can be done smoothly.
• Don’t washing the clothes touching with kerosene, gasoline, alcohol and other flammable materials.

Detergent Dispenser

1. Pre wash detergent
2. Main wash detergent
3. Softener

Caution!

Detergent only need to be added in “case I “after selecting pre-washing for machines with this function.

Note!

• As for the agglomerated or ropy detergent or additive, before they are poured the detergent box, it is suggested to use some water for dilution to prevent inlet of detergent box from being blocked and overflowing while filling water.
• Please choose suitable type of detergent for the various washing temperature to get the best washing performance with less water and energy consumption.

Control Panel

Model:WMTL-712

Note!

The chart is for reference only, Please refer to real product as standard.

1. On/Off
   Product is switched On/Off.

2. Option
   This allows you to select an additional function and will light when selected.

3. Display
   The display shows the settings, estimated time remaining, options, and status messages for your washer. The display will remain on through the cycle.

4. Start/Pause
   Press the button to start or pause the washing cycle.

5. Programs
   Available according to the laundry type.

Option

Pre Wash
The Prewash function can get an extra wash before main wash,it is suitable for washing the dust rises to surface of the clothes;You need to put detergent into the Case (I) when select it.

Extra Rinse
The laundry will undergo extra rinse once after you select it.

Delay
Set the Delay function:

1. Select a programme;
2. Press the Delay button to choose the time (the delaying time is 0-24 H/3H-6H-9H);
3. Press [Start/Pause] to commence the delay operation

Cancel the Delay function:
Press the [Delay] button until the display is 0 H.It should be pressed before starting the program. If the program already started, should switch off the program to reset a new one.

Caution!

If there is any break in the power supply while the machine is operating, a special memory stores the selected program and when the power is restarted, the program will continue.

Model: WMTL-712

Means optional (Some models have an intelligent weighing function, please refer to the actual product)

Child Lock
To avoid misoperation by children.

Caution!

• Press the two buttons for 3 sec. also to be released the function.
• The “Child Lock” will lock all buttons except the Power button.
• Cut off the power supply, the kid’s protection is to be released.

Mute the buzzer

To act the buzzer function, press the button again for 3 seconds. The setting will be kept until the next reset.

Caution!

After tying the buzzer function, the sounds will not be activated any more.

My Cycle
To memory the frequently used programme.
After choosing the programme and setting the options, press [Temp.] 3 sec. before start to wash.The default setting course is Cotton.

Programmes

Programmes are available according to the laundry type.

Washing Programmes Table

Model:WMTL-712

• The EU energy efficiency class is: A+++
  Energy test program: Cotton Eco.
  Speed: the highest speed; Other as the default.
  Half load for7.5Kg machine:3.75Kg.

• “Cotton Eco 60/40°C ” is the standard washing programs to which the information in the label and the fiche relates, and they are suitable to clean normally soiled cotton laundry and that they are the most efficient programmes in terms of combined energy and water consumptions for washing that type of cotton laundry, that the actual water temperature may differ from the declared cycle temperature.

Note!

The parameters in this table are only for user’s reference. The actual parameters maybe different with the parameters in above mentioned table.

MAINTENANCES

Cleaning And Care

Warning!

Before your maintenance starts, please unplug the machine and close the tap.

Cleaning The Cabinet

Proper maintenance on the washing machine can extend its working life. The surface can be cleaned with diluted non-abrasive neutral detergents when necessary. If there is any water overflow, use the wet cloth to wipe it off immediately.
No sharp items are allowed.

Note!

Formic acid and its diluted solvents or equivalent are forbidden, such as solvents or chemical products,etc.

Cleaning The Drum

The rusts left inside the drum by the metal articles shall be removed immediately with chlorine-free detergents.
Never use steel wool.

Note!

Don’t put laundry in the washing machine during the drum cleaning.

Cleaning The Inlet Filter

Note!

Inlet filter must be cleaned if there is less water.

Washing the filter in the tap

1. Close the tap.
2. Remove the water supply hose from the tap.
3. Clean the filter.1
4. Reconnect the water supply hose.

Washing the filter in washing machine:

1. Screw off the inlet pipe from the backside of the machine.
2. Pull out the filter with long nose pliers and reinstall it back after being washed.
3. Use to clean the filter.
4. Reconnect the inlet pipe.

Note!

• If the brush is not clean, you can pull out the filter washed separately;
• Reconnect, turn on the tap.

Clean The Detergent Dispenser

1. Press down the arrow location on softener cover inside the dispenser drawer.
2. Lift the clip up and take out softener cover and wash all grooves with water.
3. Restore the softener cover and push the drawer onto position.
4. Pull out the dispenser drawer with press the A
5. Clean the dispenser drawer under water
6. Insert the dispenser drawer

Note!

Do not use alcohol,solvents or chemical products to clean the machine.

Cleaning The Drain Pump Filter

Warning!

• Be careful of the hot water!
• Allow detergent solution to cool down.
• Unplug the machine to avoid electrical shock before washing.
• Drain pump filter can filter the yarns and small foreign matters from the washing.
• Clean the filter periodically to ensure the normal operation of washing machine.

1. 1. Open the lower cover cap

2. Open the filter by turning to the counter clockwise
3. Remove extraneous matter
4. Close the lower cover cap

Caution!

• Make sure that valve cap and emergency drain hose are reinstalled properly, cap plates should be inserted aligning to hole plates otherwise water may leak.
• When the appliance is in use and depending on the programme selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the cover, ensure it is securely re-tightened.

Trouble Shooting

The start of the appliance does not work or it stops during operation.
First try to find a solution to the problem, If not, contact the service centre.

Note!

After the check, activate the appliance. If the problem occurs or the display shows other alarm codes again, contact the service.

Technical Specifications

Product Fiches

Note!

• Programme setting for testing in accordance with applicable standard En60456.
• When using the test programmes, wash the specified load using the spin speed.
• The actual parameters will depend on how the applicance is used,and maybe different with the parameters in above mentioned table.
• The household washing machine is equipped with power management system.The duration of the left-on mode time is less than 10 minute.
• The noise emissions during washing/spinning for the standard washing cycle at full load.

Remarks:

1. The is from A(highest efficiency) to D (lowest efficiency)
2. Energy consumption per year, based on 220 standard washing cycles for standard programme at 60°C and 40°C at full and partial load, and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used.
3. Water consumption per year based on 220 standard washing cycles for standard programme at 60°C and 40°C at full and partial load. Actual water consumption will depend on how the appliance is used.
4. Spin-drying efficiency class from G (least efficient) to A (most efficient).
5. The standard 60°C programme and the standard 40°C programme are the standard washing programmes. These programmes are suitable to clean normally soiled cotton laundry and they are the most efficient programmes in terms of combined energy and water consumptions for washing that type of cotton laundry. The actual water temperature may differ from the declared cycle emperature.
   Please choose the suitable type of detergent for the various washing temperatures to get the best washing performance with less water and energy consumption.

CONDITIONS OF COMMERCIAL WARRANTY

This appliance has a repair warranty of two years from the date of sale, against any malfunction from the manufacture, including labor and spare parts. To justify the purchase date will be required to submit the invoice or receipt. This warranty is only effective in Spain.

WARRANTY EXCLUSIONS

• The appliances for professional use in industrial or commercial establishments
• The devices were improperly used so not in accordance with instructions.
• The devices are dismantled or manipulated by people outside Technical Services authorized.
• Periodic maintenance of the product.
• Malfunctions caused by acts of God, force majeure or accidents resulting from improper installation.
• Broken or damaged materials for wear or normal use, joints, plastic, glass, brushes, etc.

References

• Sauber | Electrodomésticos de confianza

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>