socket mobile AC4088-1657 Charging Mount User Guide

Package Contents

• Charging Mount
  

• USB Charging Cable
  

• Hanger Bolt
  

• 2 x Hex Nuts

• Command Bar code label to place on mount

Product Information

Charging Mount

*Illuminates Red when connected to AC adapter.

Assembly Overview

• A. Charging Mount
• B. Micro USB (2m)
• C. Cushion Crown
• D. Pem Cap / Camera Mount*
• E. 2 x Hex Nuts
• F. Hanger Bolt*
  Optional for Camera Mount
  **Optional for table mount

How to connect USB Cable

• A. Remove Micro USB cover.
• B. Insert Micro USB connector into port and fit usb cable into the cord keeper.
• C. Secure the cable to prevent from movement.

Charging Mount Operations

When charging the scanner, make sure the charging pins on the Mount and the scanner make contact with each other and the red LED on the Mount is illuminated.

Command Barcodes

Charging Mount Modes

Mobile Mode – Normal (default) Scan- ning this barcode will enable the scan- ner to enter mobile mode. It will always be in manual trigger mode even when placed in the mount or cradle.
Scanner Factory Reset returns to Mo- bile Mode.|

FNB 41FBA50000#

Auto Mode (Presentation Mode) Scanning this barcode will enable the scanner to enter auto mode. When the scanner is in auto mode, it will switch to presentation trigger mode when it detects power on the cradle pins. When the scanner is removed from the cradle it will remain in presentation trigger mode until the users press the trigger.
At that point it will switch to normal manual trigger mode. Auto Mode com- mand barcode is also printed on the product label.|

FNB 41FBA50003#

Auto Mode

Auto Mode (In the Mount)

Action

| Behavior| Notification
---|---|---
Beep Pattern| LED Activity|

Vibrate

Place Scanner in the Mount| Scanner switches to Presenta- tion Mode| High-high tone confirms proper seat- ing*| Battery status LED is disabled| None
Place a barcode in the scanner’s field of view| Decode Barcode| 1 Beep when data successfully scanned| Green LED blinks (while scanning)| None

Auto Mode: Barcodes placed in the Scanner’s field of view are automatically scanned.

*Note: Auto Mode available with the following scanners: D740, D745, D750, D755, D760, S740, S760.

Mobile Mode (Not in the Mount)

Action

| Behavior| Notification
---|---|---
Beep Pattern| LED Activity|

Vibrate

Remove the Scanner from the Mount and press the Trigger button| Scanner switches to Mobile Mode| None| Battery Status LED is Enabled| Enabled
Press the Trigger button| Decode Barcode| 1 Beep when Data successfully scanned| Green LED blinks (while scanning)| Vibrate when Data successfully scanned

Mobile Mode: Pressing the Trigger button initiates a scan.

1. Pair and connect the D740, D745, D750, D755, D760, S740, S760 to your device prior to placing the scanner in Auto Mode. The Scanner is not discoverable when in Auto Mode and in the Mount. This facilitates a fast connection to the current connected device when powered on (for example the start of the new business day).
2. The Trigger button must be pressed to disable Presentation Mode (and enable Mobile Mode) after the scanner is removed from the Mount.
3. The Scanner will not turn off when its in Presentation Mode and in the Mount under AC Power.
4. To avoid excessive power drain, the scanner should not be left out of the Mount in Auto Mode. Either press the Trigger button or Power off the scanner.

Instructions for Mounting on wooden surface

We include a Hanger Bolt to secure the Charging Mount directly to a wooden surface. Since the Pem Cap connects to a Camera Mount, popular with IP Cameras, many OEM solutions are available which do not require the Hanger Bolt.

If you plan to use the Hanger Bolt follow the special instructions for mounting on a wooden surface.

If you have many Hanger Bolts to install, you may want to use a 1/4”-20 Hanger Bolt Driver with an Electric Screw Driver. (Image below)

Special instructions for mounting on wooden surface:

1. Screw two Hex nuts (1/4”-20 thread, not included) onto the machine-threaded portion of the Hanger Bolt.
2. Use an open-ended wrench to lock the nuts against each other.
3. Drill a pilot hole into the surface you wish to place the Charging Mount.
4. Thread the lag portion of the Hanger Bolt into this surface as far as you can by hand.
5. Use a wrench on the outermost nut to drive the Hanger Bolt into the surface.
6. When the lag portion is sufficiently threaded, unjam the two nuts from each other, and run them off (unscrew them).

Configuration When Using a Camera Mount

• A. Attach the Pem cap to your Camera Mount (1/4” – 20, 3/4” depth thread) and turn to the right.
• B. Attach the Charging Mount to the Pem cap.

Product Specifications

Dimensions

Charging Mount Width| 1.80 in (46 mm)
Charging Mount Length| 5.50 in (140 mm)
Antimicrobial Rating| JLS z2801:2000 Test: 2.49 on MRSA 6.07 when cleaned with SaniCloth Plus cloth wipes Biosafe HM4100, EPA#83019-1

Compliance Statement

CE MARKING AND EUROPEAN UNION COMPLIANCE
The unit under test was found compliant with all the applicable Directives, 2004/108/EC and 2006/95/EC.

WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
The WEEE directive places an obligation on all EU-based manufacturers and importers to take-back electronic products at the end of their useful life.

ROHS STATEMENT OF COMPLIANCE
This product is compliant to Directive 2011/65/EU. NON-

MODIFICATION STATEMENT
Changes or modifications not expressly approved by the party responsible for compliance.

Helpful Resources

Technical Support & Product Registration:
http://support.socketmobile.com

Phone: +1 800-279-1390 (US Toll Free)
+1 510-933-3020 (Worldwide)

Socket Mobile Developer Program:
Learn more at: https://www.socketmobile.com/developers

The User’s Guide (full installation and usage instructions) and Command Barcodes (Advanced Scanner Configurations) can be download at: https://www.socketmobile.com/support/downloads

© 2020 Socket Mobile, Inc. All rights reserved.

Socket®, the Socket Mobile logo, SocketScan®, DuraScan®, DuraSled™, DuraCase™ and Battery Friendly® are registered trademarks or trademarks of Socket Mobile, Inc. Microsoft® is a registered trademark of Microsoft Corporation in the United States and other countries. Apple®, iPad®, iPad Air®, iPad mini®, iPad Pro®, iPhone®, iPod touch®, Objective-C®, Swift™, and Xcode® are registered trademarks of Apple, Inc., registered in the U.S. and other countries. The Bluetooth® Technology word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Socket Mobile, Inc. is under license. Other trademarks and trade names are those of their respective owners. Socket Mobile is not affiliated with Socket Internet Inc., a provider of data, voice and Internet communications services.

References

• Barcode Scanner, NFC Reader Writer Support - Socket Mobile
• CaptureSDK Developer Portal iOS, Android - Socket Mobile
• Product Support Manuals & Image Downloads - Socket Mobile

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>