gazzini 10040695 Bar End Mirror Instructions

gazzini 10040695 Bar End Mirror

What’s included

1a. Angular mirror housing, including stem
1b. Round mirror housing, including stem
2. Grub screw ISO 4027 M3x6 A2
3. Mirror screw connection
4. Ball head mount
5. Clamping sleeve screw
6. Threaded flange
7. Clamping sleeve set

General information

Reading and keeping the instructions for use

These instructions for use apply exclusively to the aforementioned gazzini Bar-End Mirrors (for short: mirrors). They contain important information on installation, safety and the warranty. Read these instructions carefully, in particular the safety instructions, before using the mirror. Failure to follow the instructions can result in damage to the mirror itself or to your motorcycle, make it less safe to ride on the road, and possibly cause consequential damage. Keep these instructions for future reference. If you pass the mirror on to a third party, you must also hand over these instructions.
The instructions for use are based on the standards and regulations applicable in the European Union and refl ect current state-of-the-art technology. If abroad, you should also observe any country-specifi c guidelines and laws.

Explanation of symbols

The following symbols and signal words are used in these instructions.

| This symbol/signal word indicates a hazard with a medium risk level which, if not avoided, may result in death or serious injury.
---|---
| This symbol/signal word indicates a hazard with a low risk level which, if not avoided, may result in minor or moderate injury.
| This signal word warns of possible material damage.
| This symbol indicates useful additional information about assembly or usage.
| This symbol indicates that the packaging and product can be recycled.

Safety

Intended use

The gazzini Mirror is used as a replacement for a faulty original mirror or for enhancing the look of the motorcycle. The mirror is designed for tubular motorcycle handlebars with an outside diameter of 22 mm (metric) and an inner diameter of between 13.5 and 18 mm. The ends of the handlebar must be open, i.e. they must not be blocked by thread inserts or similar.
The mirror is E-approved and road-legal in member states of the European Union and states signed up to the ECE regulations.
To ensure that you use the components correctly and safely on your motorcycle, always adhere to the specifi cations in your vehicle owner’s manual and the directions of the vehicle manufacturer.
The gazzini Mirror must only be used as described in these instructions. Any other use is considered improper use and can result in material damage. The manufacturer and supplier accept no liability for damage caused by improper or incorrect use.

Safety instructions

Danger for children and persons with reduced physical, sensory or mental abilities (e.g. partially disabled persons, elderly persons with reduced physical and mental abilities) or lack of experience and knowledge (e.g. older children)!

• The product includes small parts and packaging which could be swallowed. Keep these out of the reach of children, as there is a risk of asphyxiation if they are swallowed.

Risk of injury!

• When installing the mirror, ensure that the vehicle cannot topple over and that the workplace is well lit.

Risk of accident!

• For your own safety when riding your motorcycle, the mirror must be installed in such a way that it gives you an adequate view of following traffic.
• The mirror must be securely installed – If it were to fall off, it could endanger other road users and cause an accident.
• When installing the mirror stem on the handlebar end, you must ensure that it does not prevent the throttle twistgrip from moving freely. The twistgrip must be able to spring back by itself from any position when you release it.

Risk of damage!

• Ensure that the mirror never makes contact with any other part of the vehicle (fairing, tank etc.) and does not impede the rider in any way, even when the handlebar is turned to full lock.

Installation

Preparation

First jack up the vehicle securely in a well lit place. To install the gazzini Bar-End Mirror you require metric handlebars (outside diameter 22 mm) with freely accessible, open bar ends with an inner diameter of 13.5 to 18 mm.
Any existing mirror and bar ends must be removed for installation purposes.

Installation

Only select the clamping sleeve (3 or 4) with the most suitable handlebar inner diameter from the items included, and push a suitable spacer sleeve (5, 6 or 7) over the clamping sleeve. Insert the clamping sleeve screw (1) through the threaded fl ange (2). Screw on the clamping sleeve (3 or 4) with the threaded cone (8) and pre-tighten it so that the sleeve spreads a little and can still just be pushed into the handlebar. In some circumstances it will be necessary to fi t the enclosed large clamping sleeve (4) in order to fi ll out the handlebar tube as much as possible. Then insert the clamping sleeve into the handlebar and make sure that the respective spacer sleeve (5, 6 or 7) is also inserted in the handlebar tube at the beginning. Then tighten the clamping sleeve screw (1) with a hexagon key (size 5) so that the threaded fl ange (2) is screwed to the handlebar firmly so that it cannot twist.

Then place the plastic mount for the ball head (3) on the head of the clamping sleeve screw (1) and screw the mirror screw connection (4) onto the threaded fl ange (2) with an open-end wrench (size 19).

Risk of accident!

• Make sure that the throttle twistgrip on the motorcycle is not impeded by the mirror base or the fl ange. There should be 2 mm of free space between the throttle twistgrip and the mirror base. The throttle twistgrip must turn easily and spring back by itself when released.

Now sit on your motorcycle and adjust the mirror until you have an optimal view of following traffic. Check again that the throttle twistgrip is not trapped on the right-hand side. Make sure that the mirror does not hit against any part of the bike when the steering is at full lock. Then tighten the grub screw (5) in the mirror screw connection with a hexagon socket head (size 2).

Storage

Until it is installed, the gazzini Mirror should be kept in its original packaging and stored in a place that is protected against weather and moisture.

Cleaning and care

Use warm soapy water or motorcycle cleaner and a soft cloth to clean the gazzini Mirror. Do not under any circumstances use cleaners which may corrode aluminium. Finally, apply motorcycle wax to seal the surface of the mirror and protect it against the weather. Take care not to get any wax on the mirror lens.

Disposal

Dispose of packaging material and the product itself in accordance with applicable local regulations.

Contact

If you have any questions about the product and/or these instructions, before using the product for the first time, please contact our Technical Centre by e-mail at: service@louis.eu. We will help you as quickly as possible. This is the best way to ensure that the product is used correctly.

Exklusiv-Vertrieb:
Detlev Louis Motorrad-Vertriebsgesellschaft mbH
Rungedamm 35 • 21035 Hamburg • Germany
Tel.: 00 49 (0) 40 – 734 193 60 • www.louis.de • service@louis.de
Detlev Louis AG • Oberfeld 15 • 6037 Root LU • Switzerland
Tel.: 00 41 (0) 41 - 455 42 90 • service@louis-moto.ch

References

• moto.ch - Das Motorrad-Portal
• Moto.fr : Pièces détachées moto
• Moto usate e moto nuove. Forum e news su Moto.it
• Louis – Motorradbekleidung und -technik | Louis ?

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>