gazzini 10013450 GPS Mount for Handlebars Instruction Manual

Mazzini 10013450 GPS Mount for Handlebars Instruction

ARTICLE NAME

What’s included

1. Handlebar clamp Ø 22.2 mm (metric) or Ø 28.6 mm (double-butted) – depending on design
2. Cheese head screw with hexagon socket head DIN 6912 M5 x 16 A2
3. Locknut M10 x 1.0
4. Threaded pin M10 x 1.0 / M6
5. Universal joint
6. Flat-head bolt with hexagon socket head ISO 7380 M6 x 12 A2
7. Strut, hole spacing 85 mm
8. Flat-head bolt with hexagon socket head ISO 7380 M6 x 12 A2
9. Strut with ball head and cap nut
10. Base plate for sat nav or sat nav case

General information

Reading and keeping the instructions for use
These instructions for use apply exclusively to the aforementioned gazzini Sat Nav Mounting Bracket. They contain important information on installation, safety and the warranty. Read these instructions carefully, in particular the safety instructions, before installing the sat nav mounting bracket. Failure to follow the instructions can result in damage to the sat nav mounting bracket itself or to your vehicle, make it less safe to ride on the road, and possibly cause subsequent damage. Keep these instructions for future reference. If you pass the sat nav mounting bracket on to a third party, you must also hand over these instructions.
The instructions for use are based on the standards and regulations applicable in the European Union and reflect current state-of-the-art technology. If abroad, you should also observe any country-specific guidelines and laws.

Explanation of symbols
The following symbols and signal words are used in these instructions.

WARNING!    This symbol/signal word indicates a hazard with a medium risk level which, if not avoided, may result in death or serious injury.

CAUTION! This symbol/signal word indicates a hazard with a low risk level which, if not avoided, may result in minor or moderate injury.

IMPORTANT! This signal word warns of possible material damage.

This symbol indicates useful additional information about assembly or usage.
This symbol indicates that the packaging and product can be recycled.

Safety

Intended use
The gazzini Sat Nav Mounting Bracket is used for universal and flexible installation of sat navs from various manufacturers or sat nav cases. The sat nav mounting bracket is for motorbike handlebars with an outside diameter of 22 mm (metric) or 28.6 mm (double-butted). To ensure that you use the components correctly and safely on your motorcycle, always adhere to the specifications in your vehicle owner’s manual and the directions of the vehicle manufacturer.
The gazzini Sat Nav Mounting Bracket must only be used as described in these instructions.Any other use is considered improper use and can result in material damage. The manufacturer and supplier accept no liability for damage caused by improper or incorrect use.

Safety instructions

WARNING!

Danger for children and persons with reduced physical, sensory or mental abilities (e.g. partially disabled persons, elderly persons with reduced physical and mental abilities) or lack of experience and knowledge (e.g. older children)!

The product includes small parts and packaging which could be swallowed. Keep these out of the reach of children, as there is a risk of asphyxiation if they are swallowed.

CAUTION!

Risk of injury!
When installing the mirror, ensure that the vehicle cannot topple over and that the workplace is well lit.

Risk of accident

• In order to use the sat nav mounting bracket safely, it must be installed on the vehicle in such a way that it does not impede the rider’s view of the road or traffic. This also applies to the road behind you – mirrors must not be covered.

• The sat nav mounting bracket must be securely installed. If it were to fall off, it could endanger other road users and cause an accident.

• The sat nav mounting bracket must be installed so that a good view of the sat nav is ensured without distracting the rider from the traffic.
  IMPORTANT!

• Ensure that the sat nav mounting bracket never comes into contact with any other part of the vehicle (fairing, tank etc.) and does not impede the rider in any way, even when the handlebar is turned to full lock.

Installation

Preparation
First jack up the vehicle securely in a well lit place. To install the gazzini Sat Nav Mounting Bracket you require handlebars with an outside diameter of 22 mm (metric) or 28.6 mm (double-butted). The installation position must also be selected so that the rider’s vision is not obstructed by the sat nav mounting bracket or the sat nav.
Installation

1. Select the clamp (1) to suit the purchased design: 22 mm or 28.6 mm and find a suitable place on the handlebar which has a width of at least 20 mm. Make sure that the diameter of the handlebar in this area is even and not tapered.

2. Place the clamp around the handlebar and align it. Tighten the cheese head screw (2) with a hexagon key (size 4).

3. Components 3 + 4 + 5 are already joined together. Now screw this unit into the clamp (1) and secure it gently against the clamp (1) with the lock nut (3).

4. The strut (7) can either be inserted into the universal joint (5) or omitted depending on the given constructional conditions.

5. Connect the universal joint (5) and strut (7) using the flat-head bolt (6) and gently tighten it with a hexagon key (size 4).

6. Now insert the strut with the ball head and cap nut (9) into the upper section of the strut (7) and connect both sections using the flat-head bolt (8). Gently tighten the bolt with a hexagon key
   (size 4).

7. Then fasten the base plate for the sat nav (10) using the cap nut of the strut (9).

8. Now align the sat nav mounting bracket to suit your own requirements and tighten the bolt connections. Tighten the lock nut (3) against the clamp (1) with an open-ended wrench (size 15) and the flat-head bolts (6 + 8) with a hexagon key (size 4). Only tighten the cap nut under the base plate (10) finger-tight.

9. Now fasten the corresponding adapter for the respective sat nav or sat nav case to the base plate.

10. If necessary, align the sat nav mounting bracket again as described.

Storage

Until it is installed, the gazzini Sat Nav Mounting Bracket should be kept in its original packaging and stored in a place that is protected against weather and moisture. The air humidity should not exceed 80%.

Cleaning and care

Use warm soapy water or motorcycle cleaner and a soft cloth to clean the gazzini Sat Nav Mounting Bracket. Do not under any circumstances use cleaners which may corrode aluminium. Finally, apply polishing wax to seal the surface and protect it from the weather.

Warranty

This product comes with the statutory two-year warranty. The warranty period begins on the date of purchase. It does not cover normal wear and tear, use for anything other than the intended purpose, or damage caused by an accident, tampering or attempted repairs by unauthorised persons or customer service departments.
Disposal

Dispose of packaging material and the product itself in accordance with applicable local regulations.

Contact
If you have any questions about the product and/or these instructions, before using the product for the first time, please contact our Technical Centre by e-mail at: service@louis.eu. We will help you as quickly as possible. This is the best way to ensure that the product is used correctly. Made in Taiwan

References

• Moto.fr : Pièces détachées moto
• Moto usate e moto nuove. Forum e news su Moto.it
• Louis – Motorradbekleidung und -technik | Louis ?

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>