gazzini POLY-10040763 Fairing Mirror Set Round Instruction Manual

: June 6, 2024
: gazzini

Table of Contents

gazzini POLY-10040763 Fairing Mirror Set Round
What’s included
General information
Safety
Installation
Storage
Cleaning and care
Warranty
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

gazzini POLY-10040763 Fairing Mirror Set Round

What’s included

Art. No. 10040763

Mirror housing
Mirror stem
Mirror mount
Hexagon socket screw DIN 912 M5 x 20
Washer DIN 126 11
Hexagon socket screw ISO 7380 M10x1.5 x 25
Hexagon socket screw DIN 6912 M10x1.25 x 25
Hexagon socket screw DIN 6912 M10x1.25 LH x 25

General information

Reading and keeping the instructions for use
These instructions for use apply exclusively to the gazzini Super Moto Mirror shown above (for short: mirrors). They contain important information on installation, safety and the warranty. Read these instructions carefully, in particular the safety instructions, before using the mirror. Failure to follow the instructions can result in damage to the mirror itself or to your motorcycle, make it less safe to ride on the road, and possibly cause consequential damage. Keep these instructions for future reference.

If you pass the mirror on to a third party, you must also hand over these instructions. The instructions for use are based on the standards and regulations applicable in the European Union and reflect current state-of-the- art technology. If abroad, you should also observe any country-specific guidelines and laws.

Explanation of symbols
The following symbols and signal words are used in these instructions.

WARNING!
This symbol/signal word indicates a hazard with a medium risk level which, if not avoided, may result in death or serious injury.

CAUTION!
This symbol/signal word indicates a hazard with a low-risk level which, if not avoided, may result in minor or moderate injury.

IMPORTANT!
This signal word warns of possible material damage.
This symbol indicates useful additional information about assembly or usage.
This symbol indicates that the packaging and product can be recycled.

Safety

Intended use
The Cassini mirror is intended as a replacement for a defective original mirror or to enhance the look of your motorcycle. It is designed to be installed on an existing mirror bracket.
The mirror is E-approved and road-legal in member states of the European Union and states signed up to the ECE regulations.
To ensure that you use the components correctly and safely on your motorcycle, always follow the specifications in your vehicle owner’s manual and the directions of the vehicle manufacturer.
The gazzini mirror must only be used as described in these instructions. Any other use is considered improper use and can result in material damage. The manufacturer and supplier accept no liability for damage caused by improper or incorrect use.

Safety instructions

WARNING!

Danger for children and persons with reduced physical, sensory or mental abilities (e.g. partially disabled persons, elderly persons with reduced physical and mental abilities) or lack of experience and knowledge (e.g. older children)! The product includes small parts and packaging which could be swallowed. Keep these out of the reach of children, as there is a risk of asphyxiation if they are swallowed.

CAUTION!

Risk of injury! When installing the mirror, ensure that the motorcycle cannot topple over and that the workplace is well lit.

CAUTION!

Risk of accident!

For your own safety when riding your motorcycle, the mirror must be installed in such a way that it gives you an adequate view of following traffic.
The mirror must be securely installed. If it were to fall off, it could endanger other road users and cause an accident.

IMPORTANT!

Risk of damage! The mirror must never make contact with any other part of the motorcycle (fairing, tank etc.) or impede the rider in any way, even when the handlebar is turned to full lock.

Installation

Preparation
First, jack up the motorcycle securely in a well-lit place.
As the mirror is designed to be installed on an existing mirror bracket, as shown in the following diagram for example, your existing mirror must first be removed.
Then check that there is sufficient space for installing the gazzini mirror.

Installation
First check which of the three hexagon socket screws supplied (6, 7, 8) M10x1.5, M10x1.25 or M10x1.25 with left-hand thread (Yamaha, right side) fits in the original mirror bracket, and screw it into the mirror base. Motorcycles over 125cc from other Japanese manufacturers generally have a thread with a diameter of 10 mm and a pitch of 1.25 (written: M10x1.25). Newer BMWs with a short thread tend to have a thread diameter of 10 mm, but a pitch of 1.5 mm. Gazzini mirror adapters are also included for these.

Fasten the pre-assembled mirror stem (2) and mirror mount (3) with one of the hexagon socket screws (6, 7, 8) and the washer (5) using a hexagon key (size 8), but do not tighten fully so that it can still be moved easily.

Then install the mirror housing (1) in one of the 4 holes in the mirror stem (2) using an open-end wrench (size 8) so that it gives you the best possible view. Apply medium-strength threadlocker (available separately) to the thread before screwing in.

Aligning the mirror
Now align the mirror so that it provides a good view of the road behind you. Then tighten the hexagon socket screw (6, 7 or 8) fully with a hexagon key (size 8), and hexagon socket screw (4) with a hexagon key (size 4).

Check that the mirror does not hit against any part of the motorcycle when the steering is at full lock, and check once more that all the screws are firmly fastened.

Storage

Until it is installed, the gazzini mirror should be kept in its original packaging and stored in a place that is protected against weather and moisture.

Cleaning and care

Use warm soapy water or motorcycle cleaner and a soft cloth to clean the gazzini mirror. Never use any sort of cleaner that may corrode aluminum. Finally, apply polishing wax to seal the surface of the mirror and protect it against the weather. Take care not to get any wax on the mirror lens.

Warranty

This product comes with a statutory two-year warranty. The warranty period begins on the date of purchase. It does not cover normal wear and tears, use for anything other than the intended purpose, or damage caused by an accident, tampering, or attempted repairs by unauthorized persons or customer service departments.

Disposal

Dispose of packaging material and the product itself in accordance with applicable local regulations.

Contact

If you have any questions about the product and/or these instructions, before using the product for the first time, please contact our Technical Centre by e-mail at: service@louis.eu. We will help you as quickly as possible. This is the best way to ensure that the product is used correctly.
Made in Taiwan

Exklusiv-Vertrieb:
Detlev Louis Motorrad-Vertriebsgesellschaft mbH Rungedamm 35 • 21035 Hamburg • Germany
Tel.: 00 49 (0) 40 – 734 193 60 • www.louis.de • service@louis.de
Detlev Louis AG • Oberfeld 15 • 6037 Root LU • Switzerland Tel.: 00 41 (0) 41 - 455 42 90 • service@louis-moto.ch
ANL-10040763-01-2104