Tize TZ-912 Rechargeable and Waterproof Remote Dog Training Collar User Guide
- June 6, 2024
- TIZE
Table of Contents
- Features
- How does the Rechargeable and Waterproof Dog Training Collar Work
- Components
- Key Definition
- Operation Guide
- How to use the Remote Transmitter
- Frequently Asked Questions
- General Tips for Training Your Dog
- Indicator & Display
- FCC Caution
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
TZ-912 Rechargeable and Waterproof Remote Dog Training Collar
User Guide
Rechargeable and Waterproof Remote Dog Training Collar Operation Guide
Please read the entire guide before using
Thanks for choosing the Rechargeable and Waterproof Remote Dog Training
Collar. Our mission is to provide you with the safety tools and techniques to
train your dog.
Features
-
Rechargeable Remote Transmitter
-
Rechargeable and Waterproof Receiving Collar
-
2000 feet remote control range between Remote Transmitter and Receiving Collar.
-
Beep Mode activates a correcting tone on the Receiving Collar
-
Adjustable vibration intensity level from 14 level
-
Adjustable static shock intensity level from 1-8 level (optional)
-
Power saving modes:
• The Reit: Wing Cots will go Into Standby Mode ff Ifs idle for more than 5 mils. My movements wi activate the Receiving Collat.
• The Transmitter will go Into Standby Med. (O will be light off with the 30s. o w 4, will be light off with I mil). Press o o s button to reactivate it from Standby mode. -
The Remote Transmitter can be used to control up to 4 Receiving Collars.
-
2 pairs of metal Contacts (1 Short and ‘I long) are included 10 Suit the length of your dogs hair.
-
The Transmitter with hock key function.
How does the Rechargeable and Waterproof Dog Training Collar Work
The Rechargeable and Waterproof Training Collar has been proven to be safe.
comfortable. and an effective training system for all dogs weighing over
151bs. This system slows you to control yow dog within a range of up to 2000
feet. At the press of a button, the Remote Transmitter sends a signal to the
Receiving Collar and activates a Beep, a Vibration, or a Static Shock
correction output. By using the Training Collar properly, you can cone much of
your dog’s undesired behavior and teach basic and advanced obedience commands.
Important: the Training Collar has an effective range up to 2000 feet.
Hold the Remote Transmitter horizontally away from your body to achieve the
optimum range. Terrain features, weather, vegetation, transmission from other
radio devices, and other factors may affect the range of the Remote
Transmitter.
Precautions
DO NOT use this product for aggressive dogs or vicious animals. Risk of skin
damage. It’s important to fit the collar properly. A collar that is fitted too
tightly or ‘yam for too long may harm your dog’s skin. This condition, which
ranges from redness to pressure ulcers, is commonly known as bed sores.
CAUTION
- Do not let your dog wear the collar for more than 12 hours per 24-how period.
- If possible, gently reposition the collar on your dog’s neck every t or 2
- Never attach a lead to the Receiver Collar, as this would cause excessive pressure on the contact pants.
- When using a separate collar to connect a leash. please ensure that d does not put excessive pressure on the electronic collar.
- Examine yow dog’s neck daily for signs of chafing or soreness.
- If a rash or sore is found. stop using the collar till the injured skin has been healed
- If the condition persists for more than 48 hews, consult your veterinarian.
- If possible. please use the Beep Mode or Vibration Mode at first, they can try the Static shock function.
Please ensure that you charge both the Receiving collar and the Remote Transmitter before using’ To extend the battery life of this product, please charge them per month if you do not intend to use it for a long period of time.
Components
Key Definition
- LED screen
- Level rotary knob
- Shock button
- Vibration button
- Beep button
- Channel button
- Lock key switch
- Charging port
1-8 level
Beep mode
Vibration mode
Full battery
Static shock mode
Ful battery
Singal mark| Low battery
Key lock
1 Dog 1
2 Dog 2
Dog 3
4 Dog 4
---|---
-
LED Screen:
• Beep mode: When this symbol le is displayed, press the Cm button to activate a Beep tone on the Receiving Collar.
• Vibration Mode: when this symbol Lei is displayed, press the like a button to activate Vibration.
• Use the level Up/ Down buttons to adjust the intensity of the vibration from 1 to 8.
• Static Shock Mode: when this symbol * is displayed, press the I, button to activate Static Shock.
• Use the level Up/ Down buttons to adjust the intensity of the shock from 1 to 8.
• Signal: when this symbol is displayed, means the transmitter is launching the signal.
• Full battery: when this symbol 0 is displayed when charging, means the battery is in full.
• Low battery: when this symbol it is displayed, means the transmitter is in low battery and needs to be recharged.
• Keylock: when this symbol/display, mean the transmitter is under key lock. -
Level rotary knobs: they are used to adjust the Intensity of the Vibration or Shock from the lowest level 1 to the highest level 8.
-
Shock/Vibration/Beep button: press this button to launch the correct signal.
-
Channel button: press this button to change between the 1-4 Receiving Collar (if applicable).
-
Key Lock switch: push up/down the switch to lock/unlock the key function.
-
Charging port: plug the USB charging cable into the port to charge the Remote Transmitter.
• Lithium battery: 3.7V 500mAh for the Remote Transmitter 3.7V 250mAh for the Receiving Collar “Operating Frequency: RF433 MI-IZ
• Contact points: 2 pairs of metal contacts to be chosen to suit the length of your dog’s hair. ‘ Mini Spanner: a tool to screw/unscrew contact points on the electrodes.
Contact Points:
Deliver vibration /safe static correction
Operation Guide
Step
Preparing the Remote Transmitter. Charging the Remote Transmitter
- Plug the USB Charging Cable into the Charging port.
- Plug the Adapter into a standard outlet.
- The number 0 on the LCD screen will be lit circularly when charging.
- The LED screen will show once it’s fully charged within 2.5 hours. Remove the USB Charging Cable. Low battery Indicator.
- The LED screen will show II and flash for 30seconds, then the transmitter will be turned off automatically.
How to use the Remote Transmitter
- Push down the key lock switch, the LED screen right
- Press ShocklVibration/Beep button, the LED screen will display (an ea 4), which means the corresponding mode is activated.
- Rotating to set the intensity of shock or vibration.
- Select different channels for 1 – 4 Receiving Collars.
Power Saving Mode : the Remote Transmitter will go into Standby Mode if
it is idle for 1 min. The LED screen on the Remote Transmitter will not
display anything in this case(0 will be light off with the 30s. ES 4 will be
light off with min), press any button to re-activate it. Lock Key function:
Push up the lock switch, the ( k)will flash for 6 seconds, then it goes Into
key lock mode, and it won’t be activated anymore, the ( 8 ) will flash for 6
seconds again if any button is pressed. Push down the lock switch, the
Transmitter will work.
Step 2 Preparing the Receiving Collar:
Charging the Receiving Collar
- Remove the rubber cover and plug the USB Charging Cable into the charging port.
- Plug the Adapter into a standard outlet.
- The red LED will keep lighting when the Receiving Collar is charging.
- The green LED will be lighting once it’s fully charged with 1.5 hours.
- Remove the Charging Cable. and put back the rubber cover.
Low battery indicator: The red LED will be flash within 30seconds, then
Receiving Collar will be turned off automatically. How to use the Receiving
Collar. Press the On/off button to turn the Receiving Collar on, the green
indicator light will blink.
Power Saving Mode: The Receiving Collar will go into Standby Mode if it
is idle for more than 5 mins. Any movements will activate the Receiving
Collar. If the Receiving Collar does not be activated when you press the s air
yon Transmitter, and the Green LED on receiving collar is not on, then gently
shake the Receiving Collar, the Receiving Collar will be activated and the
Green LED light will illuminate.
Step Encoding the Remote Transmitter and the Receiving Collar:
- Push down the lock switch to make sure the Transmitter in on work status.
- Press the (El to cho
- Press the On/off button to turn on the Receive the On/off button until the red and green indicator light blink alternately, then press any button of Beep/Vibration/Shock to encode. the green indicator light will blink, they are encoded su
Note: Most of the Rechargeable and Waterproof Training Collars have
already been encoded before leaving the factory. If so, Just press any button
on the transmitter to activate, then press the with 1 sec on receiving collar
to turn on it. after that. you can test the function refer to step 4. (Page 9)
Step 4 Testing the Rechargeable and Waterproof Training Collar:
Testing the Static Shock * Function The static impulse generated by the
Receiving Collar cannot be seen by naked eyes. Test whether the Static Shock
Function works by using the following procedure:
- Remove the Test Light from the package and connect it to the contact points on the receiving collar.
- Press the * button on Remote Transmitter to launch the Static Shock signal, if the Test Light flashes, the Static Shock Function Is working correctly.
- The intensity of the Static Shock can be adjusted by rotating the rotary knob from level 1-to 8.
Testing the Vibration a Function
- Press the fl button on Remote Transmitter to launch the vibration signal, if the Receiving Collar vibrates, the Vibration function works correctly.
- The intensity of the vibration can be adjusted by rotating the rotary knob from level 1-to 8.
Testing the Beep EP Function
• Press the D3 button on Remote Transmitter to launch the beep signal, if the
Receiving Collar beeps, the Beep Function works correctly.
Step Fining the Receiving Collar to your dog:
-
Center the Contact Points under your dog’s neck(A).
-
The Receiving Collar should be positioned snugly around your dog’s neck. Important: Make sure that you can fit one finger between the strap and your dog’s neck(B).
Note: Choose the correct Contact Points to suit the length of your dog’s hair. If your dog has long hair or a thick coat, use the longer Contact Points.
Frequently Asked Questions
-
How old does my dog have to be before I start using the Rechargeable and Waterproof Training Collar?
A: Your pet should be able to recognize basic commands such as “Sr and “Stay!”. The Rechargeable and Waterproof Training Collar may be too large for dogs weighing less than 15Ibs. The Receiving collar is adjustable in length from 9.5 to 26 inches. If your dog’s neck is smaller than 26 inches, please cut the redundant part. This product is not suitable for dogs with necks larger than 26 inches. -
Once my dog is trained and has learned to obey my commands, will he have to continue wearing the Receiving Collar?
A: Probably not, although you may need to reinforce the training with the Receiving Collar from time to time. -
Is the Receiving Collar waterproof?
A Yes. In fact, your dog can swim while wearing the Receiving Collar Must seal well the charing port tightly, and keep it dry after get wet. -
What is the lifespan of lithium batteries?
A: The Lithium battery in the Remote Transmitter and the Receiving Collar can be charged for 400 times. -
How long should the training session for my dog be?
A: The training sessions should be kept short for maximum effectiveness. It’s advised not to train your dog for more than 10-15 mins at a time.
I have fitted the Rechargeable and Waterproof Training Collar correctly, but my dog is not responding.
-
Ensure that the batteries are fully charged. You need to charge both the Remote Transmitter and the Receiving Collar for about 2 hours before they can be used for the first time.
-
Check the Remote Transmitter can adjust the intensity level of the vibration or static shock to a higher level than level 1.
-
Restart the Receiving collar by pressing the On/ Off button.
-
Test the 3 functions (Beep. Vibration and Static Shock) before using the Receiving Collar for the first time please refer to “Step 4” (page 9) for instructions on how to do this.
-
The Receiving collar will go into Standby Mode if it is idle for more than 5 minutes. Any movements will re-activate it.
-
Make sure that the Contact Points are touching your dog’s skin.
-
Trim your dog’s fur where the Contact Points touch the neck. Ensure that you are using the correct set of Contact Points suitable for the length of your dog’s fur.
-
If none of the above works, encode the Remote Transmitter and the Receiving Collar again. See “Step 3” (Page 9) for instructions on how to do this.
I am trying to test the Receiving Collar manually, but it does not work. -
If you want to test the Receiving Collar manually on your hand or leg. please touch the 2 Contact Points simultaneously. Touching only one of the Contact Points will not work.
The Receiving Collar is broken. It has not worked since I dropped it. -
The Receiving Collar is not designed to be drop-proof. Please do not drop the Receiving Collar, as this will damage the interior circuits.
The Remote Transmitter does not work -
You must charge the Remote Transmitter before you use it for the first time. Charging time is typically 2.5 hours.
-
Ensure that the Remote Transmitter has adequate power.
-
Remote Transmitter will automatically go into Standby Mode if it is idle for 1 min. No LED light will be illuminated at this time Press any button to re-activate the Remote Transmitter.
General Tips for Training Your Dog
- Eliminate one behavioral problem or teach one command at a time. If you move too fast with the training, your dog may become confused.
- Be consistent. Give your dog a single Beep. Vibration, or Static Shock for each misbehavior.
- Do not over-correct your dog. Use a few stimulations as possible during training.
- Unless you can supervise him/ her, it is recommended that you restrain your dog from environments In which he/ she has a history of misbehaving. However, setting up a training session, in this case, can dramatically improve your chances of success.
- If your dog reacts to the training by hiding or acting fearfully, redirect his/ her attention to a simple and appropriate behavior, such as the”Sit!” command.
Common Sizes of Different Dog Breeds
Common | Sizes of | Different Dog Breeds | |
---|---|---|---|
Size | Neck (cm) | Chest (an) | Back (cm) |
Mini | 20-22 | 25-30 | 19 |
Small | 20-24 | 29-36 | 23 |
Medium | 23-28 | 35-42 | 28 |
Large | 27-31 | 41-47 | 31 |
Large | 30-34 | 46-53 | 35 |
Large | 33-37 | 52-59 | 40 |
Huge | 43-48 | 76-84 | 60 |
47-52 | 88-97 | 65 | Labrador Retriever |
52-62 | 92-100 | 70 | Golden Retriever. Old English Sheepdog |
Common Weights of Different Dog Breeds
Large Dogs(Body height over 61cm, weight over 68Ibs)
Medium Dogs( Height 40.7-61cm, Weight 24-86Ibs)
Small Dogs(Height 25.5-40.7cm. Weight 8-221bs)
Mini Dogs(Height under 25cm, Weight under Sibs)
Indicator & Display
Receiving Collar Indicator
| |
stays on| Blink| stays on| Blink| blink alternately
Charging| Low Battery| Full Charge| Work| Encoding
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>