cecotec 900 Ultimate Ergowet Upright Vacuum Instruction Manual

cecotec 900 Ultimate Ergowet Upright Vacuum Instruction Manual

SAFETY INSTRUCTIONS

Read these instructions thoroughly before using the appliance. Keep this instruction manual for future reference or new users.
Make sure that the mains voltage matches the voltage stated on the rating label of the appliance and that the wall outlet is grounded.
This product is designed only for household use. It is not suitable for commercial or industrial use.
Check the power cord regularly for visible damage. If the cord is damaged, it must be replaced by the official Technical
Support Service of Cecotec in orderto avoid any type of danger.
Do not use the device if it has been dropped or if there are any visible signs of damage.
Do not try to repair the device by yourself.
Contact the official Technical Support Service of Cecotec for advice.
Do not use any accessory that has not been recommended by
Cecotec, as they might cause injuries or damage.
Do not place the appliance close to heat sources, flammable substances, wet surfaces where it can fall or be pushed into water or allow it to come into contact with water or other liquids. Do not use outdoors.
Do not use the appliance to vacuum liquids, lighted matches, cigarette ends, hot ash or on wet surfaces.
Do not use on concrete, tarmac or other rough surfaces.
Take special care when using the device to clean stairs.
Do not block the appliance’s openings or hinder air flow. Keep openings free of any objects such as dust, lint, clothing or
fingers. Keep hair away from moving parts.
Turn off and unplug the appliance from the mains supply when it is not going to be used for a long period of time, before cleaning or repairing, before attaching components and before removing the battery.
Never modify the charger in any way.
Do not use any battery that has not been provided with the original product or by Cecotec.
Do not carry the battery by the cord or coil the cord around the battery to store it.
Always operate and store the devices in places where the room temperature is between 5 and 40 ºC.
Make sure the high-efficiency filter and the main rolling brush are properly installed before operating the device.
Pullfrom the plug, not the cord, to disconnect it from the outlet.
Do not immerse the cord, plug, or any non-removable part of the appliance in water or any other liquid, nor expose the electrical connections to water. Make sure your hands are dry before handling the plug or switching on the appliance.
The appliance is not intended to be used by children under the age of 12.
It can be used by children over the age of 12, as long as they are given continuous supervision.
This product can be used by children and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, as long as they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Close supervision is necessary when the appliance is being used by or near children.

Battery instructions
This appliance includes Li-ion batteries, do not incinerate or expose them to high temperatures, as they may explode.
Leaks from the battery or battery cells can occur under extreme conditions. Do not touch any liquid that leaks from the battery. If the liquid gets into contact with skin, wash immediately with soap and water. If the liquid gets into the eyes, flush them immediately with clean water for a minimum of 10 minutes and seek medical attention. Wear gloves to handle the battery and dispose of immediately in accordance with local regulations.

Avoid contact between the battery and small metallic objects such as paper clips, coins, keys, nails or screws.
Before a new battery is used or the battery is used for the first time after long-term storage, fully charge the battery.
When the device is stored and not used for long periods of time, ensure that the battery pack is fully charged, and ensure that the battery is charged and discharged at least once every three months.

PARTS AND COMPONENTS

Fig. 1 (Page 35)

1. Suction base
2. Floor brush release button
3. Vacuuming tube release button
4. Dust tank bottom cover unlock button
5. Dust tank emptying button
6. Speed-control dial
7. Display
8. On/off button
9. Power adapter
10. Fast charge base
11. Includes a 2-in-1 narrow accessory for corners and furniture
12. Includes a wide 2-in-1 accessory for corners and furniture
13. Motorised brush for upholstery.
14. Union elbow
15. Long brush
16. Flexible hose
17. Flex vacuuming tube
18. Jalisco brush
19. Best Friend Care special brush for pet hair
20. Special brush for fabrics
21. Wet scrubbing accessory with mop
22. Flex button

Fig. 1.1 (Page 35)

1. Display
2. Speed-control dial
3. On/off push button

BEFORE USE

Take the product out of the box.
Check for any visible damage. If any is observed, contact as soon as possible the Technical Support Service of Cecotec for advice or reparation.
Fully charge the device before the first use.
During the first 3 uses, it is recommended to charge the device for 12 hours between uses.
Once the battery has been charged and used, it will start charging normally.
The normal charge time is 2 hours approx. When the battery is fully charged, unplug it.

PRODUCT ASSEMBLY

Vacuuming tube and suction base assembly
To install the suction base into the vacuuming tube, align both of them making sure the tab on the suction base matches the guides on the tube, and introduce one into the other until they are firmly fixed. To disassemble them, press the suction base release button and pull from the vacuuming tube while you hold the suction base.
Warning: When assembling these 2 parts, make sure the handle and the brush are facing the same direction.
Use the Flex tube to reach and vacuum dirt from the most inaccessible zones. Press the Flex button to bend the tube.
Fig. 2/2.1/2.2 (Page 35, 46)

PRODUCT ASSEMBLY

Vacuuming tube and suction base assembly
To install the suction base into the vacuuming tube, align both of them making sure the tab on the suction base matches the guides on the tube, and introduce one into the other until they are firmly fixed. To disassemble them, press the suction base release button and pull from the vacuuming tube while you hold the suction base.
Warning: When assembling these 2 parts, make sure the handle and the brush are facing the same direction.
Use the Flex tube to reach and vacuum dirt from the most inaccessible zones. Press the Flex button to bend the tube.
Fig. 2/2.1/2.2 (Page 35, 46)

Battery assembly
Introduce the battery in the slot located in the handheld vacuum cleaner. Once it is introduced, it will click into place. Move it slightly to ensure it is properly assembled in place.
Note: Take the battery out and store it in a safe, dry place if the device is not going to be used in a long period of time.

Fig. 3 (Page 46)
Following the below illustration, keep the vacuuming tube vertically, align the tab on the vacuuming tube with the guides in the handheld vacuum cleaner and introduce the tube.

Dust tank and handheld vacuum cleaner assembly
To assemble the dust tank to the handheld vacuum cleaner, first separate the handheld vacuum cleaner from the vacuuming tube.
Then, press the vacuuming tube release button with one hand and, holding from the handle with the other one, turn the dust tank anticlockwise to the unlock position indicated on the dust tank edge.
Fig. 4 (Page 46)

OPERATION

Wall charging base installation
First, fix the charging base to the wall. To do so, we recommend you place a protective film (not included) on the wall’s surface. Then, put the charging base on the wall and make 3 corresponding to the holes to be drilled in order to fix the base. Take into account the height of the installation, it is important that suction base rests on the floor to avoid the charging base from holding all the vacuum cleaner’s weight. Make 3 holes on the wall and fix the charging base with the supplied M4 x 32 nuts and screws.

The height should be 102.5 mm from the base of the wall charging base to the ground.
Make sure that the charging base is securely fixed on the wall, place the vacuum cleaner on the charging base as shown in figure 5 by putting the vacuum cleaner’s charging terminals into contact with the charging base’s ones (plastic tab).
Fig. 5 (Page 46)
Once the wall charging base is installed, the charging port must be connected to the power adapter, and then the device can be charged by sliding it from top to bottom into the wall charging base.

Charge and display
When the battery percentage is 20 % or below, the device will automatically enter low consumption mode. It is recommended to charge the device when it reaches this percentage.
The battery must be charged while it is inside the device, and on the fast charge base.
Connect one of the ends of the power adapter to the power supply and the other to the fast charge base. During charging, the charge light indicator will turn on red and will turn green once the charge is completed.
In order to charge only the battery, plug the power adapter and connect the other end of the cord to the battery. During charging, the charge light indicator will turn on red and will turn green once the charge is completed. The display will show the battery charge. Fig. 6 (Page 46)

Charging modes
Charging mode 1
Fig. 7 (Page 46)
Fig. 8 (Page 46)

Charging mode 2
Fig. 9 (Page 46)

Charging mode 3
Fig. 10 (Page 46)

How to use the handheld vacuum cleaner
Press the On/off button to turn the device on or off.
Press the speed control dial to select the device operating speed: Low, Medium, High or Smart. The device will start operating at low speed by default, and the screen will display “LOW”. The battery percentage and sync will also be displayed.
Press the speed control dial to set the device at medium speed. “MED” will be displayed on the screen. The battery percentage and sync will also be displayed. 2/3 of the opening radio will be shown (vacuuming).
Press the speed control dial to set the device at high speed. “HIGH” will be displayed on the screen. The battery percentage and sync will also be displayed. The vacuuming opening radious will be completely shown. Press the speed control dial to set the device at Smart speed. Under this mode, the device will automatically adjust suction power according to the concentration of dust and to the amount of dust on the floor brush. “AUTO” will be displayed on the screen. The battery percentage and sync will also be displayed. The screen will display: the amount of absorbed dust, 1/3 when the concentration opening radious is low, 2/3 when the concentration opening radious is medium and the full display when the concentration opening radious is high. When operating at high speed and the battery is 20 % or lower, the device will automatically switch to medium speed in order to lengthen the battery life. Fig. 11 (Page 47)

How to use the suction base for floors
It removes dust from carpets, hard and soft floors, and tiles.
If too many particles or fibres are vacuumed, or if a child touches the brush during operation by accident, the rotary brush stops spinning automatically in order to prevent tangles and possible damage.
Both brushes can be equally assembled to the suction base:
Best Friend Care brush
Removes pet hair from all types of surfaces, including carpets and mats.
Jalisco brush Vacuum 3 times more dust in one pass. It is recommended to use it on hard floors, but it can be used on soft ones too. Fig. 12 (Page 47)

Includes a 2-in-1 narrow accessory for corners and furniture
Includes a 2-in-1 narrow accessory for corners and furniture
Suitable for cleaning doors, windows, narrow corners, etc.
Fig. 13 (Page 47)
Suitable for cleaning sofas, cabinets and wardrobes, windows, etc.
Fig. 14 (Page 47)

Long brush
Fig. 15 (Page 48)
Fig. 16 (Page 48)
Suitable for cleaning surfaces which are sensible to scratches such as furniture, wardrobes, etc.

Flexible hose
It can be assembled onto the device for a more flexible cleaning, to reach the most difficult corners.

Motorised brush for upholstery.
Removes dust mites and bacteria from beds and sofas.
Fig. 17 (Page 48)

Union elbow
Suitable for cleaning dust from high wardrobes, roofs, windows, corners, etc.
Fig. 18 (Page 48)

Special brush for fabrics
Adjustable accessory to remove all types of dust trapped in fabrics.

Installation of accessories
Fig. 19 (Page 48)
Fig. 19.1 (Page 49)

CLEANING AND MAINTENANCE

Disconnect the appliance from the power supply and allow it to cool down before cleaning.
Use a soft, damp cloth to clean the device’s surface.
Do not immerse the appliance in water or other liquid.
Do not use abrasive cleaners or scouring pads to clean the product.
It is recommended to clean the dust tank after every use. If the device clogs due to built-up excessive dust, clean it or replace it.
After the brush has been used for a long time, bristles might start to tangle with hair and other particles. Clean it in order for it to operate correctly again.

Cleaning the dust tank and the filters (Page 50)
Fig. 20
Fig. 21
Fig. 22

Open the dust tank bottom cover unlock button and empty the dust inside.
Hold the device from the handle and pull from it upward to separate de device from the dust tank.
Turn the filter as shown on the image and disassemble the filter.
After washing and drying all the parts, assemble it back in order to use it again.

Cleaning the Jalisco brush and the Best Friend Care brush
Move the rotary brush release button with the finger toward the arrow and remove the cover of one of the ends of the brush.

Take one end of the brush out as shown on the image. After washing and drying all the parts, assemble it back in order to use the brush again. Fig. 23 (Page 50)

Removing the battery
Press the battery release button and take the battery out as shown on the image. Store the battery in a plastic bag and leave it in a dry place.
Fig. 24 (Page 51)

Storing the device
If the robot is not going to be used for a long time, remove the battery from the product and store it in a dry and safe place.

Dirt sensors
When the device does not detect dirt or dust, or detects very little, the screen will display a full circle when turned on. In this case, wipe the dirt sensors with a soft, dry cloth. Fig. 25. (Page 51)

When the vacuum cleaner is not going to be used for a long time, please remove the
water tank and empty the remaining water. Do not expose it to direct sunlight or to damp
environments.
Mop installation/removal
Removing/installing the water tank
Fig. 25 (Page 51)
In order to install/remove the cleaning cloth you must first disassemble the water tank from the rest of the appliance. In order to remove the water tank, use your foot to hold it against the ground and pull upward until it unclicks from position.
Once the cloth has been installed and the water tank has been filled, to reinstall the water tank, simply push it back together until it clicks into position.
Note: Do not use cleaning agents. Use clean and room temperature water only. Do not use the vacuum cleaner to vacuum water.

Installing the mop cloth
Place the mop cloth on the ground with the Velcro facing upwards. Align the mop cloth with the Velcro strips on the water tank and attach it. Fig. 26 (Page 51)

Water emission
Fig. 27 (Page 51)
When using this product for the first time, make sure the water tank lid is not fully open.
When not in use, pay attention to the water emission push button and to the tank lid, as
water leak may occur when the water tank is full.
To activate water emission, the water emission push button must be pressed, and to stop water emission, the push button must be released as shown on the following figure.
Note: If the vacuum cleaner is not going to be used for a long period of time, make sure to remove the water tank and to empty the remaining water. Do not expose it to direct sunlight or to damp environments.

Removing the mop cloth
To remove the mop cloth, just hold it with your hand and pull form it to detach it from the water tank.

Cleaning and maintenance
Cleaning the water tank
To clean the water tank, fill the tank with clean water, shake it and then empty it.
The mop is washable; therefore, it is suggested to wash it after every use.
Replace the cloth after 20-30 uses, depending on the use.
When the mop cloth is used for a long time, it is possible that the water output is affected.
This can be avoided by cleaning both cloth and water tank regularly.

TROUBLESHOOTING

ERROR CODES

Note:
The low battery warning will disappear when the charger is disconnected.
Low battery error (excluding shut down due to low battery), will stop after 10 seconds. If not, press the on/off button to stop it.
Communication or NTC error: It will stop after 50 seconds.

TECHNICAL SPECIFICATIONS

Product reference: 05708
Product: Rockstar 900 Ultimate
100-240 V ~ 50/60 Hz
Motor rated power: 550 W
Brush rated power: 50 W
Made in China | Designed in Spain

DISPOSAL OF OLD ELECTRICAL APPLIANCES

The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), specifies that old household electrical appliances must not be disposed of with the normal unsorted municipal waste. Old appliances must be collected separately, in order to optimize the recovery and recycling of the materials they contain and reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your obligation to dispose of the appliance correctly. If the product has a built- in battery or uses batteries, they should be removed from the appliance and disposed of appropriately. Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.

TECHNICAL SUPPORT AND WARRANTY

This product is under warranty for 2 years from the date of purchase, as long as the proof of purchase is submitted, the product is in perfect physical condition, and it has been given proper use, as explained in this instruction manual.
The warranty will not cover the following situations:
The product has been used for purposes other than those intended for it, misused, beaten, exposed to moisture, immersed in liquid or corrosive substances, as well as any other fault attributable to the customer.
The product has been disassembled, modified, or repaired by persons, not authorised by the official Technical Support Service of Cecotec.
Faults deriving from the normal wear and tear of its parts, due to use.
The warranty service covers every manufacturing defects of your appliance for 2 years, based on current legislation, except consumable parts. In the event of misuse, the warranty will not apply.
If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact Cecotec Technical Support Service at +34 963 210 728.

www.cecotec.es

Grupo Cecotec Innovaciones S.L.
C/ de la Pinadeta s/n, 46930
Quart de Poblet, Valencia (Spain)
PELI01200824

References

• SmartGroup

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>