dns TWP1 True Wireless Earbuds User Manual
- June 6, 2024
- dns
Table of Contents
TWP1 True Wireless Earbuds
User Manual
Introduction
Most ice cream true wireless Bluetooth earphones are derived from the creativity of ice cream. The extremely colorful design is comfortable and close to the ear. Features: 1. Really wireless, free from cables, listen to what you want at any time; 2. Perfect sound quality, rich and delicate, 3. Comfortable to wear, smart touch, easy to enjoy music; 4.Noise cancellation in call environment; 5. Low game latency of 50 milliseconds.
Product parameter
Bluetooth version: Rev 5.0 Bluetooth range: about 10 meters Support Bluetooth profile: A2DP, AVRCP, HFP, SPP Support audio codec: SBC Battery life: up to 4 hours/time, battery life 10 hours (charging box) Speaker moving coil drive: 6mm dynamic moving coil drive Frequency response range: 20-20,000Hz Waterproof rating: IPX4 (earplugs only) Speaker sensitivity: 95dB at 1KHz ±3dB Speaker distortion: -‘, 3% Speaker impedance: 320 ± 15% MIC sensitivity: -42dB at 1KHz ±3dB MIC impedance: 2.2K0 ± 15%
Package list
Product overview
Instructions
First connection:
- Get out the Bluetooth earphone from the charging box, the earphone will automatically turn on;
- Turn on the Bluetooth function of the phone/tablet/computer…, find “TW-P1+” in the available devices list ( in the Bluetooth device manager), and click to automatically pair.
Note: When you want to reset the earphone, please touch the L or R earphone 5 times in the power-on state, the earphone will back to the default unpaired state.
Earphone touch function
Music: Play/Pause (L/R)
Incoming call: Answer (L/R)
Music: Previous (L) / Next (R)
Incoming call: Hang up (L / R)
Voice Assistant (L/R)
Music: Press and hold any earphones for 5 seconds to turn off both ears, and
press and hold for 5 seconds again to start the earphones and automatically
connect to the phone. Incoming call: Long press for 1 second to reject the
call (L / R)
Earphone LED indicators
Slow flashing yellow light: connected to the device
Yellow/red cross flashing: enter pairing mode
Fast flashing red light: low battery
Steady red light: charge the battery
Steady yellow light (30 seconds): the battery is fully charged
The LED indicator on the Charging box
When charging:
Greenlight is on: fully charged, power: 100%
Red light is on: charging, power: 1%-99%
Note: fully charging the battery box from 1% to 100% will take about 2.5-3
hours (the earphones can be charged simultaneously when placed in the charging
box) .
When not charging:
Red flashing light: low battery warning, 20%
Warning
To avoid the risk of fire, the equipment is supplied only by the external power source of which output shall comply with PS1 (with output capacity less than 15W).
CAUTION
Risk of explosion if the battery is replaced by an incorrect type.
Replacement of a battery with an incorrect type can defeat a safeguard.
Disposal of a battery into fire or a hot oven, or mechanically crushing or
cutting of a battery, that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment can
result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure may result in an explosion
or the leakage of flammable liquid or gas.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
The device must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device complies with FCC’s radiation exposure limits set forth for an
uncontrolled environment
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>