LIVARNO LED Wall and Ceiling Lamp Instruction Manual
- June 6, 2024
- LIVARNO
Table of Contents
LIVARNO LED Wall and Ceiling Lamp Instruction Manual
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the device.
List of pictograms used
Read the instructions!
This light is suitable only for interior use, in dry and enclosed spaces.
Alternating current (type of current and voltage)
Volt
Hertz (mains frequency)
Watt (effective power
Protective conductor
Observe the warning and safety instructions!
Switching cycles
This light is only suitable for indoor use in dry and enclosed spaces.
Electric shock warning! Danger to life!
This light is not suitable for external dimmers or electronic switches.
For your safety
Caution! Risk of burns due to hot surfaces!
Lifespan
Dispose of packaging and device in an environmentally-friendly manner!
The packaging is made from 100% recycled paper.
Danger to life and risk of accident for infants and children!
Colour rendering index
Lumens
Light temperature in Kelvin
Assembly Instruction
LED Wall & Ceiling Lamp
Introduction
Congratulations on your new product. You have selected a high quality product. Please be sure to carefully read the complete operating instructions. Fold out the page with the illustrations. These instructions are part of the product and contain important information on setup and handling. Always follow all safety instructions. Before using this product for the first time verify the correct voltage and that all parts are properly installed. Should you have any questions or you are unsure about operating the product, please contact the dealer or service centre. Please keep these instructions in a safe place and pass them on third parties as applicable.
Intended use
This light is only suitable for indoor use in dry and enclosed spaces. The light can be fastened to any normally inflammable surface. This product is intended for private household use only. This product is intended for normal operation and can be used for wall or ceiling installation.
Scope of delivery
Check immediately after unpacking that the parts are complete and that the product is in proper condition.
1 LED wall and ceiling light, model 14144406L /14144408L/14144506L
3 Wall plugs
3 Screws
2 Protective tubes
1 Set of assembly instructions and instructions for use
Parts description
- Lever (14144406L /14144408L)
- Lampshade
- Light base
- Mains connection cable (external)
- Lustre terminal protective cover
- Wall plug
- Screws
- Lustre terminal
- Protective tube
Technical data
Light:
Model no.: 14144406L / 14144408L/
14144506L
Operating voltage: 230–240V∼ 50Hz
Rated power: LED 18W
Protection class: I /
IP rating: IP20
LED:
LED light bulb: LED module (permanently installed)
Rated power: 1 x max. 18W
Safety
Safety notices
Damage due to failure to comply with these operating instructions will invalidate the guarantee! We assume no liability for consequential damage! We assume no liability for material damage or personal injury due to improper handling or failure to comply with the safety instructions.
RISK OF FATAL
INJURY AND ACCIDENT HAZ-ARD FOR TODDLERS AND
SMALL CHILDREN!
Never leave children unsupervised with the packaging materials. The packaging material poses a suffocation hazard. Children frequently underestimate the dangers. Please always keep the product out of the reach of children. This device may be used by children aged 8 years and up, as well as by persons with reduced physical, sensory or mental capacities, or lacking experience and/or knowledge, so long as they are supervised or instructed in the safe use of the device and understand the associated risks. Do not allow children to play with the device. Cleaning and user maintenance must not be performed by children without supervision.
Avoid the risk of fatal injury from electric shock
- Ensure that a qualified electrician, or a person trained to carry out electrical installations, performs the electrical installation.
- Always check the light, power supply, and mains cable for damage before plugging it in. Never use the light if it shows any signs of damage.
A damaged mains cable indicates a life-threatening danger due to electric shock. In the event of damage, repairs or other problems with the light please contact the service centre or a qualified electrician.
- Prior to installation, remove the fuse or switch off the circuit breaker (0 setting) in the fuse box. Prior to installation verify the mains voltage on site corresponds with the operating voltage required for the light (see “Technical data“).
- Ensure that the light does not come into contact with water or other liquids under any circumstances.
- Never open any of the components of the electrical equipment or insert any objects into the same components. This will pose a risk of fatal injury from electric shock.
- Do not install the light on a wet or conductive substrate!
Prevent fire and injury hazards
RISK OF INJURY!
Check each light bulb and the lampshade for damage immediately after unpacking.
- Do not assemble the light if the light bulbs and/or lampshade are defective. In this case, contact the service centre for a replacement.
- Do not look directly into the light source (light bulb, LED etc.).
- Do not use optical instruments to look at the light source (e. g. magnifying glass).
- This lights’s illuminant is not replaceable; if the illuminant has reached the end of its service life, the whole light must be replaced.
- This light is not suitable for external dimmers or electronic switches.
Safe working
- Mount the light so that it is protected from moisture and dirt.
- Carefully prepare for assembly and allow yourself adequate time. Organise all parts and any necessary additional tools or materials before starting so they are easy to reach.
- Always be attentive! Always pay attention to what you are doing and use common sense. Never install the light if you are having difficulty concentrating or do not feel well.
Preparation
Required tools and material
The tools and materials specified are not included. This information and these values are non-binding and are only provided as a reference. The nature of the material is determined by the individual local conditions.
- Pencil /making tool
- 2-pole circuit tester
- Screwdriver
- Electric drill
- Bit (approx. Ø 6mm)
- Side cutting pliers
- Ladder
Prior to installation
Important: The electrical connection must be established by a qualified electrician or a person trained to perform electrical installations. This person must be familiar with the properties of the light and the connection regulations.
- Familiarise yourself with all the instructions and diagrams in this manual, as well as with the light itself, before you install it.
- Before installation ensure that the circuit, to which the light will be connected, is not energised. To do so, remove the fuse or switch off the circuit breaker in the fuse box (0 position).
- Use a 2-pole voltage tester to verify cables are not live.
Initial use
Installing the light
Model 14144406L /14144408L:
-
Before installing the light, remove the fuse or switch off the circuit breaker (0 setting) in the fuse box.
-
Remove the lampshade 2 from the light base 3 by turning the three levers 1 on the side of the light outwards (see Fig. A and B).
-
Mark the drill holes using the holes in the light base 3 intended for the screws 7 as a guide (see Fig. C).
-
Now drill the mounting holes (approx. Ø 6mm, depth approx. 40mm). Make sure that you do not damage the power cable (see Fig. D).
-
Insert the wall plugs 6 into the drilled holes.
-
Secure the light base 3 using the included screws 7 (see Fig. E). Feed the mains connection cable (external) 4 through the cable guide.
-
Remove the protective cover 5 from the lustre terminal 8 by loosening the screw (see Fig. F).
-
Pull the protective tubes 9 over cables L and N of the mains connection cable (external) 4 (see Fig. G).
-
Connect the mains connection cable (external) 4 with the light using the lustre terminal 8 .
Note: Make sure that you correctly connect each individual wire of the mains connection cable (external) 4 : live wire, black or brown = symbol L, neutral wire, blue = symbol N. Connect the protective conductor (green-yellow) with the earth terminal which is marked in the light base 3 . -
Screw the protective cover 5 of the lustre terminal 8 tightly into place again (see Fig. G).
-
Place the lampshade 2 back onto the light base 3 and close the three levers 1 (see Fig. H).
Ensure that it is securely tightened. -
Reinsert the fuse or switch the circuit breaker back on (see Fig. I).
Your light is now ready to use.
Model 4144506L:
-
Before installing the light, remove the fuse or switch off the circuit breaker (0 setting) in the fuse box.
-
Remove the lampshade 2 from the light base 3 by carefully turning it anticlockwise (see Fig. A and B).
-
Mark the drill holes using the holes in the light base 3 intended for the screws 7 as a guide (see Fig. C).
-
Now drill the mounting holes (approx. Ø 6mm, depth approx. 40mm). Make sure that you do not damage the power cable (see Fig. D).
-
Insert the wall plugs 6 into the drilled holes.
-
Secure the light base 3 using the included screws 7 (see Fig. E). Feed the mains connection cable (external) 4 through the cable guide.
-
Remove the protective cover 5 from the lustre terminal 8 by loosening the screw (see Fig. F).
-
Pull the protective tubes 9 over cables L and N of the mains connection cable (external) 4 (see Fig. G).
-
Connect the mains connection cable (external) 4 with the light using the lustre terminal 8 .
Note: Make sure that you correctly connect each individual wire of the mains connection cable (external) 4 : live wire, black or brown = symbol L, neutral wire, blue = symbol N. Connect the protective conductor (green-yellow) with the earth terminal which is marked in the light base 3 . -
Screw the protective cover 5 of the lustre terminal 8 tightly into place again (see Fig. G).
-
Secure the lampshade 2 , by screwing it clockwise onto the light base 3 (see Fig. H).
-
Reinsert the fuse or switch the circuit breaker back on (see Fig. I).
Your light is now ready to use.
Maintenance and cleaning
RISK OF ELECTRIC SHOCK!
Disconnect the light from the mains circuit before cleaning. To do so, remove
the fuse or switch off the circuit breaker in the fuse box (0 position).
RISK OF ELECTRIC SHOCK!
For electrical safety, never clean the light with water or other liquids, or
immerse it in water.
CAUTION! DANGER OF BURNS DUE TO HOT SURFACES!
Allow the light to cool completely.
- Do not use solvents, benzene or similar substances. They could damage the light.
- Only use a dry, lint-free cloth for cleaning.
- Replace the fuse or switch on the circuit breaker (I setting) inside the fuse box.
Disposal
The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.
Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1–7: plastics /20–22: paper and fibreboard/80–98: composite materials.
The product and packaging materials are recyclable, dispose of it separately
for better waste treatment. The Triman logo is valid in France only.
To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.
Warranty and service
Warranty
You receive a 36 month warranty on this product, valid from the date of purchase. The appliance has been carefully produced under strict quality control. Within the warranty period we shall rectify without charge all material and manufacturing defects. In the event of a defect during the warranty period, please send the appliance to the listed Service Centre address, referencing the following model number: 14144406L /14144408L /14144506L.
Wear parts (such as bulbs) and damage caused by improper handling, non- observance of the operating instructions or unauthorised interference are excluded from the warranty. The performance of services under the warranty does not extend or renew the warranty period.
Service address
Briloner Leuchten GmbH & Co. KG
Im Kissen 2
59929 Brilon
GERMANY
Tel.: +49 29 61/97 12–800
Fax: +49 29 61/97 12–199
E-mail: kundenservice@briloner.com
www.briloner.com
Free service number:
Tel.: 00800/27456637
IAN 354287_2010
Please have your receipt and the article number (e. g. IAN 123456_7890) ready as your proof of purchase when enquiring about your product.
Declaration of conformity
This product fulfils the requirements of the applicable European and national directives. Conformity has been demonstrated. The relevant declarations and documents are held by the manufacturer.
Manufacturer
Briloner Leuchten GmbH & Co. KG
Im Kissen 2
59929 Brilon
GERMANY
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>