vtech 80-547300 Kidi Star DJ Mixer User Guide

: June 6, 2024
: vtech

Table of Contents

vtech 80-547300 Kidi Star DJ Mixer
INTRODUCTION
INCLUDED IN THIS PACKAGE
Battery Removal and Installation
BATTERY NOTICE
PRODUCT FEATURES
GAMES DJ Party
CARE & MAINTENANCE
TROUBLESHOOTING
FCC
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

vtech 80-547300 Kidi Star DJ Mixer

INTRODUCTION

Thank you for purchasing the VTech Kidi DJ Mixer. VTech Kidi DJ Mixer features easy music creation in different styles.

Build-in voice button
Line-in button
Bluetooth button
Bluetooth Connect Button
Power Button
Turntable
Selection Buttons (Left, Right, OK)
Pause Button
Party Light On / Off selector
Party Light pattern selector
Volume Control
Tempo Buttons

INCLUDED IN THIS PACKAGE

One Kidi DJ Studio
One parent’s guide

WARNING
All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties, cords and packaging screws are not part of this toy, and should be discarded for your child’s safety.
NOTE
Please keep this parent’s guide as it contains important information.

WARNING
The tie are not part of this toy. The tie should be removed and discarded for your child’s safety.

Unlock the packaging locks:

Rotate the packaging locks 90 degrees counter-clockwise.
Pull out the packaging locks.

GETTING STARTED
This product is in Try-me mode in the packaging. Press and hold the Customize sound effect button 5 for a few seconds to proceed with normal play. If the unit powers down during the play, please install a new set of batteries.

Battery Removal and Installation

Make sure the unit is turned Off.
Find the battery cover located on the back of the unit, use a screwdriver to loosen the screw and then open the battery cover.
Remove old batteries by pulling up on one end of each battery.
Install 4 new AA (AM-3/LR6) batteries following the diagram inside the battery box. (For best performance, alkaline batteries or fully charged Ni-MH rechargeable batteries are recommended).
Replace the battery cover and tighten the screw to secure.

WARNING:
Adult assembly required for battery installation. Keep batteries out of reach of children.

BATTERY NOTICE

Insert batteries with the correct polarity (+ and -).
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries.
Only batteries of the same or equivalent type as recommended are to be used.
Do not short-circuit the supply terminals.
Remove batteries during long periods of non-use.
Remove exhausted batteries from the toy.
Dispose of batteries safely. Do not dispose of batteries in fire.
RECHARGEABLE BATTERIES:
Remove rechargeable batteries from the toy before charging.
Rechargeable batteries are only to be charged under adult supervision.
Do not charge non-rechargeable batteries.

PRODUCT FEATURES

POWER BUTTON
Press the Power Button to power on the unit. Press the button again to power off the unit.
LINE-IN JACK
Connect external player
EXTERNAL SPEAKER JACK
Connect external speaker or headphone
AC ADAPTER
Connect AC adapter power
AUTOMATIC SHUT-OFF
To preserve battery life, the KidiGo™ Fast Break Hoop will automatically turn off after 10 minutes without input. The unit can be turned on again by pressing the Power Button.

GAMES DJ Party

Launch pad buttons
Use the Launch pad buttons to choose different instruments sounds to play. Each column allows one button to be playing. The selected option is lit up.
Preset sound effect buttons
Press the Preset sound effect buttons to add build-in sound effects.
Style button
Press Style button to change the music for the Launch pad buttons and Build-in sound effect buttons
Customize SFX buttons
Hold to record your own short sound effect. It lights up to indicate recording in progress. Release the button when finished recording. Press and release immediately to play the recorded sound effect.
Turntable
Turn the Turntable to add scratch disc sound on your music.
Scratch button
Press Scratch button to choose the sound effect for the Turntable
Build-in button
Press Build-in button to add human voice track onto the music. Press again to mute it.
Line-in button
Press Line-in button to play the line-in device sound.
Bluetooth connect button and Bluetooth button
Press Bluetooth connect button to connect a Bluetooth device. After the device is connected, press Bluetooth music button to play the Bluetooth external source sound
Crossfader
Use the crossfader to adjust the volume balance between Build-in / Line-in / Bluetooth sound and the Launch pad.
Tempo control
Use the Tempo control buttons to adjust. the tempo of the Launch pad music.
Pause button
Press Pause button anytime to stop all sound. Press again to resume the sound.
Disco light control
Use the Disco light On / Off selector to switch on or switch off the disco light.
Use the Disco light Turn / Stop selector to turn or stop the disco light.
Volume control
Use the volume control to adjust the master volume.
Studio
In the main menu, choose to record or playback a track by Left, Right and OK button.
Record
Select the track you would like to record. After the countdown, recording starts.
The unit can record the Turntable, Build-in button, Launch pad, preset sound effects, customize sound effect, crossfader behaviour and tempo change status. When finish, press OK button to save your recording.
Note: If you have customize the customize sound effect later on, the customize sound effect in the recorded track will change too.
Playback
Choose the track you would like to playback by Left, Right and OK button.

CARE & MAINTENANCE

Keep the unit clean by wiping it with a slightly damp cloth.
Keep the unit out of direct sunlight and away from any direct heat sources.
Remove the batteries when the unit is not in use for an extended period of time.
Do not drop the unit on hard surfaces and do not expose the unit to excess moisture.

TROUBLESHOOTING

If for some reason the unit stops working or malfunctions, please follow these steps:

Interrupt the power supply by removing the batteries.
Let the unit stand for a few minutes, then replace the batteries.
The unit should now be ready to use again.
If the unit still does not work, install a new set of batteries.

Environmental Phenomena
The unit may malfunction if subjected to radio-frequency interference. It should revert to normal operation when the interference stops. If not, it may become necessary to turn the power off and back on, or remove and reinstall the batteries. In the unlikely event of an electrostatic discharge, the unit may malfunction and lose memory, requiring the user to reset the device by removing and reinstalling the batteries.

IMPORTANT NOTE
If the problem persists, please call our Consumer Services Department at 1-800-521-2010 in the U.S., 1-877-352-8697 in Canada, or visit our website vtechkids.com and fill out our Contact Us form located under the Customer Support link. Creating and developing VTech products is accompanied by a responsibility that we take very seriously. We make every effort to ensure the accuracy of the information, which forms the value of our products. However, errors sometimes can occur. It is important for you to know that we stand behind our products and encourage you to contact us with any problems and/or suggestions you might have. A service representative will be happy to help you.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference; and
This device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

FCC

Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
CAN ICES-003(B)/NMB-003(B)

Visit our website for more information about our products, downloads, resources and more.