Gopod GP07A Apple Watch Magnetic Charging Dock User Manual
- June 6, 2024
- Gopod
Table of Contents
Gopod GP07A Apple Watch Magnetic Charging Dock
Product introduction:
Product model: P07A
Function description: P07A mobile wireless charger, the product has a built-in
890mAH polymer battery for charging Apple Watch. The product has a MicroUSB
interface, which can be connected to an ordinary charger to charge the Apple
Watch and charge the battery at the same time. The product has 4 power
indicator lights, which can indicate the current power and charging status. It
is the best travel partner of APPLE WATCH.
Product schematic diagram:
Interface and component function description:
| SN | Interface | Description | Remark |
|---|---|---|---|
| 01 | Buckle | Easy to carry | |
| 02 | Original Apple Watch |
Wireless charging module
| Original Apple Watch wireless charging module|
03| Switch button| Control the working status of the product, click to
turn on, long press to turn off
|
04
| ****
Battery indicator LED
| Indicate the battery power and charging status, divided into 25%, 50%, 75%, 100% 4 levels, when charging, according to the level of charge to the
flashing prompt.
|
Remarks
Specifications
- Standby power consumption ＜0.1W
- Input voltage 5±0.25V
- Output voltage 5±0.25V
- Maximum input current ＜1A
- Maximum output current ＜400MA
- The ultimate conversion efficiency of the board end 83%
- Ripple voltage at the output terminal <20mV
- Product size 54.854.816.9mm
- Product weight 53g
Electrical protection requirements
Short circuit protection
When the output is short-circuited, the input power of the product will be
reduced and will not be damaged. When the short-circuit condition is removed,
the product will not be damaged.
Input overvoltage protection
When the input voltage far exceeds the rated voltage value of the product, the
product is protected without damaging the equipment.
Battery protection
When the battery is overcharged, overdischarged, reversed or short-circuited,
the battery will not be damaged and the product will not be damaged.
Unprotect
When the product is in a protected state due to improper use, recharge the
product to release the protection.
Working environment
- Operating temperature:：0°C ~ 40°C (32°F ~ 104°F)
- Storage temperature: -25°C – 45°C (-13°F – 113°F)
- Relative humidity:Non-condensing state 0% ~ 90%
Function instructions
External power charging
Use a charger with a rated output voltage of 5V and an output current greater
than or equal to 1000mA to charge the battery of the product through the Micro
5P cable. At this time, the battery indicator of the product will flash to
indicate the charge status (25%, 50%, 75%, 100%) 4 When charging, the flashing
prompt will be based on the battery level to which it is charged.) At the same
time, you can put the APPLE WATCH above the product module, and the watch will
be charged while the battery is charged by the external power supply.
Charging the built-in battery
When you need to use the built-in battery to charge the APPLE WATCH, you only need to click the power-on button. At this time, the battery indicator will flash and display according to the current battery level (25%, 50%, 75%, 100%). 4 gears, one light represents one gear), at this time, you only need to put the APPLE WATCH above the charging module, and the charging will proceed automatically. (The battery in the saturated state can provide more than 1.5 times of charging for the APPLE WATCH 1st generation).
Product considerations
- Please do not let any of the objects (such as fuel, needle) or any liquid (water, beverage) fell and infiltrate into product, leading the product can’t not normal use.
- Do not place and use the product in 1) Moisture.2) Dusty places. 3) rusty objects.
- Please keep the product in plastic bag when it’s a long time not use it. Prevent dust and oxidation resulted socket in poor contact.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning : Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. Thisequipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>