PHILIPS MG7790 Norelco Multigroom Face Styler Grooming Trimmer User Manual

PHILIPS MG7790 Norelco Multigroom Face Styler Grooming Trimmer

IMPORTANT SAFETY INSTRUCTIONS

When using an electric product, basic precautions should always be followed, including the following:
Read all instructions before using this product.

DANGER
To reduce the risk of electric shock:

• Do not reach for a corded product that has fallen into water. Unplug immediately from the power outlet.
•  Use product only in dry condition. Do not use while bathing or in a shower.
•  Do not place or store the product where it can fall or be pulled into a tub or sink. Do not place or drop the product into water or other liquid.
• Except when charging, always unplug this product from the power outlet immediately after use.
• Remove power cord from power outlet and product before cleaning.

WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:

• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for their safety. Children should be supervised to ensure that they do not play with the product.

• Use this product only for its intended household use as described in this manual. Misuse can lead do hazards or serious injuries. Do not use attachments not recommended by Philips North America LLC.

• Never operate this product if it has a damaged power cord, if it is not working properly, after it has been dropped or damaged, or after the product or power cord has been dropped into water. For assistance call 1-800-243-3050.

• Keep the power cord away from heated surfaces.

• Never drop or insert any object into any opening.

• Do not use the power cord in or near a power outlet that contains an electric air freshener to prevent damage to the power cord.

• Do not use product outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.

• Always check cutters, cutting unit and guards before using the product. Do not use the product if cutters, cutting unit or guards are damaged, as injury may occur.

• Always attach power cord to product first, then to power outlet. To disconnect, set all controls to ‚off‘ position. Then remove power cord from power outlet.

• Plug power cord directly into power outlet. Do not use an extension cord.

• Unplug power cord before plugging in or unplugging the product.

• The batteries used in this product may present a fire or chemical burn hazard if mistreated. Do not disassemble, heat above 100 °C (212 °F) or incinerate.
  IMPORTANT: The power plug contains a transformer. Do not cut off the power plug to replace it with another plug as this will cause a hazardous condition.

• Only use original Philips accessories or  consumables. Only use detachable power cord HQ8505.

• Charge, use and store the product at a temperature between 40 °F / 4.5 °C and 95 °F / 35 °C.

• Keep product and batteries away from fire and do not expose them to direct sunlight or high temperatures.

• If the product becomes abnormally hot or smelly, changes color or if charging takes longer than usual, stop using and charging the product and contact Philips.

• Do not place products and their batteries in microwave ovens or on induction cookers.

• Do not open, modify, pierce, damage or dismantle the product or battery to prevent batteries from heating up or releasing toxic or hazardous substances.

• Do not short-circuit, overcharge or reverse charge batteries.

• If batteries are damaged or leaking, avoid contact with the skin or eyes. If this occurs, immediately rinse well with water and seek medical care.

• When you handle batteries, make sure that your hands, the product and the batteries are dry.

• To avoid accidental short-circuiting of batteries after removal, do not let battery terminals come into contact with metal objects (e.g. coins, hairpins, rings). Do not wrap batteries in aluminum foil. Tape battery terminals or put batteries in a plastic bag before you discard them.

SAVE THESE INSTRUCTIONS

Introduction
Congratulations on your purchase and welcome to Philips Norelco!
To fully benefit from the support that Philips Norelco offers, register your product at www.norelco.com/register.

General description

(Fig. 1)

1. Extra-wide hair trimmer
2. Precision trimmer
3. Nose trimmer
4.  Precision shaver
5. Full-size hair trimmer
6. On/off button
7. Battery status indicator
8. Socket for small plug
9. Stubble guard 3/64in. (1mm)
10. Stubble guard 5/64in. (2mm)
11. Beard guard 1/8in. (3mm)
12.  Beard guard 3/16in. (5mm)
13.  Beard guard 9/32in. (7mm)
14.  Eyebrow guard 1/4in. (6mm)
15.  Power plug
16.  Small plug
17.  Hair guard 5/32in. (4mm)
18.  Hair guard 3/8in. (9mm)
19.  Hair guard 15/32in. (12mm)
20.  Hair guard 21/32in. (16mm)
21.  Fading hair guard 5/32in.-3/8in. (4-9mm)
22. Fading hair guard 5/32in.-3/8in. (4-9mm)
23. Body guard 1/8in. (3mm)
24.  Body guard 3/16in. (5mm)
    Not shown: cleaning brush, pouch

Charging

Battery status indications

• When the battery is almost empty, the battery status indicator lights up orange (Fig. 2).
•  When the product is charging, the battery status indicator flashes white slowly (Fig. 3).
•  During quick charge, the battery status indicator flashes white. After approx. 5 minutes of charging, the product contains enough power for one cordless trimming session.
•  When the battery is fully charged, the battery status indicator lights up white continuously (Fig. 4).
  Note: After approx. 30 minutes, the light goes out automatically.

Charging
Charge the product before first use and when the display indicates that the battery is almost empty. When the product has charged for 3 hours, it has a cordless operating time of up to 6 hours.

• Charging, recharging or using the product at temperatures below 40 °F (4.5 °C) or higher than 95 °F (35 °C) adversely affects the lifespan of the battery.
• If the product is subjected to a major change in temperature, pressure or humidity, let the product acclimatize for 30 minutes before use.

1. Make sure the product is turned off.
2.  Insert the small plug into the product and put the power plug in any 120V AC outlet (Fig. 5).
3.  After charging, remove the power plug from the wall outlet and pull the small plug out of the product.

Note: An adapter plug may be necessary for cord usage in some foreign countries. Use an attachment plug adapter of the proper configuration for the power outlet.

Quick charge
After approx. 5 minutes charging, the product contains enough power for one cordless trimming session.

Using the product

Note: This product can be used without cord or directly from the power outlet.
Note: Switch off and clean the product and attachments after each use.

•  Use this product for its intended household use as described in this manual.
•  For hygienic reasons, the product should only be used by one person.
•  Trimming is easier when the skin and hair are dry.
•  Be careful when you are trimming without a guard because the cutting unit removes every hair it touches.

Detaching and attaching cutting elements

1. To detach a cutting element, push upwards against the teeth of the cutting element and take it off the handle (Fig. 6).
2.  To attach a cutting element, insert the lug of the cutting element into the guiding slot at the front and push the back of the cutting element onto the product (‘click‘) (Fig. 7).

Detaching the precision shaver and nose trimmer

1.  Place your finger on the arrow at the back of the attachment and push it off the handle in the direction of the arrow (Fig. 8).

Attaching and detaching guards

1. To attach any type of guard onto a cutting element, slide the front part of the guard onto the teeth and push the projection at the back of the guard into the product (‘click‘) (Fig. 9).
2. To detach any type of guard from the cutting element, carefully pull its back part off the product and then slide it off the cutting element (Fig. 10).

Note: When trimming for the first time, start by using the guard with the maximum trimming length setting to familiarize yourself with the product.

Switching the product on and off

1. Press the on/off button once to switch the product on or off (Fig. 11).

Attachments for use on beard
Full-size hair trimmer
Use the full-size hair trimmer without a guard to trim hair close to the skin (to a length of 1/32 in./0.5 mm) or to create clean lines around your beard, neck and sideburns.

1. To trim hair close to the skin, place the flat side of the cutting element against your skin and make strokes against the direction of hair growth (Fig. 12).
2. For contouring, hold the cutting element perpendicular to the skin and move it upwards or downwards with gentle pressure (Fig. 13).

Beard guards
Attach a beard guard to the full-size hair trimmer to trim your beard and moustache evenly. The product comes with 5 beard guards. The hair length settings are indicated on the guards. The settings correspond to the remaining hair length after trimming.

Guard                  inch            mm

Stubble guard           3/64 in.            1 mm

Stubble guard           5/64 in.            2 mm

Beard guard              1/8 in.              3 mm

Beard guard              3/16 in.            5 mm

__ Beard guard              9/32 in.            7 mm

Attach the guard to the full-size hair trimmer.
To trim the most effective way, move the guard against the direction of hair growth (Fig. 14). Make sure the surface of the guard always stays in contact with the skin.

Attachments for use on body

• Use the green body guards to trim body hair.
•  When you trim for the first time, use the 3/16 in./5 mm body guard to familiarize yourself with the product.
• Make sure hair is clean and dry as wet hair tends to stick to the body and, when trimming sensitive areas, always use a body guard.
• Since hairs do not all grow in the same direction, you may want to try different trimming positions (i.e. upwards, downwards, or across). Practice is best for optimum results.
•  Always make smooth and gentle movements and be sure the surface of the guard always stays in contact with your skin.
•  When too many hairs have accumulated on the product, blow the hairs out before use, for best trimming results.

Body guards
Attach a body guard to the full-size hair trimmer to trim hairs below the neckline. The product comes with 2 body guards. The hair length settings are indicated on the guards. The settings correspond to the remaining hair length after trimming.

__**Guard                    inch            mm**

Body guard (green)      1/8 in.             3 mm

Body guard (green)      3/16 in.           5 mm

1. Attach a guard to the extra-wide hair trimmer.
2. Move the trimmer slowly over the crown from different directions to achieve an even result. Make sure the surface of the guard  always stays in contact with the skin.
   Always move the trimmer against the direction of hair growth (Fig. 17). Press lightly.
   Make overlapping passes over the head to ensure that all hair that should be cut has been cut.

Fading hair guard
Attach the fading hair guards to the extrawide hair trimmer to trim the hair around the ears with a faded result. The product comes with 2 guards. Use both guards to trim hair around both ears. Choose a hair guard based on the preferred trimming direction of back to front or front to back. Always make sure that you hold the side of the guard with the short teeth closest to your ear.

Guard             inch              mm

Fading hair        5/32 in.-             4-9 mm

guards                3/8 in.

1. Attach the guard to the extra-wide hair trimmer to trim the hair around the ear.Then attach the other guard to trim the hair around the other ear.
2. Place the product on your hair at the back or front of your ear, depending on the trimming direction you prefer. Always make sure that the side of the guard with the short teeth is closest to your ear.
3. Move the trimmer slowly around the ear, while holding it steady (Fig. 18). For best results, move the trimmer against the direction of hair growth (back to front).

Precision attachments for use on face Precision trimmer
Use the precision trimmer to create fine lines and contours around your facial style, close to the skin (to a length of 1/32 in./0.5 mm).

1.  Hold the precision trimming head  perpendicular to the skin and move the trimming head upwards or downwards with gentle pressure (Fig. 19).

Eyebrow guard
Use the full-size hair trimmer with
the eyebrow guard attached for tidying up eyebrows or trimming sideburns to a length of 1/4 in./6 mm.

1.  Slowly move the trimmer against the hair growth direction. Press lightly and make sure that the surface of the comb always stays in contact with the skin (Fig. 20).

Nose trimmer
Use the nose trimmer to trim your nose hair and ear hair.

•  Make sure nasal passages are clean. Make sure outer ear channels are clean and free from wax.
•  Do not insert the tip more than 3/16 in./5 mm.
•  Always clean the attachment after each use.

Trimming nose hair

1. Gently move the tip in and out of nose while turning it around to remove unwanted hairs (Fig. 21).

Trimming ear hair

1.  Slowly move the tip round the ear to remove hairs that stick out beyond the rim of the ear.
2.  Gently move the tip in and out of the outer ear channel to remove unwanted hairs (Fig. 21).

Precision shaver
Use the precision shaver after trimming, to shave unwanted hairs on cheeks, chin and along the beard with precision. Make sure to pre-trim your beard first, with the full-size hair trimmer without guard, to obtain the best result.

Note: Use the precision shaver to remove remaining hairs and detailing your beard style. It is not suitable for a full face shave.

1. Gently press the precision shaver onto the skin and shave along contoured edges to remove any unwanted hairs (Fig. 22).

Travel lock
The product is equipped with a travel lock function. You can use the travel lock if you are going to store the product for a longer time period or if traveling. The travel lock prevents the product from being switched on by accident.

Activating the travel lock

1.  Press the on/off button for 3 seconds (Fig. 11).
   When the travel lock is activated, the battery status indicator flashes orange(Fig. 2).
   Deactivating the travel lock

2.  Press the on/off button for 3 seconds (Fig. 11).
   The product is now ready for use.

Note: The product unlocks automatically when connected to an electrical outlet

Cleaning

Never use scouring pads, abrasive cleaning agents or aggressive liquids such as gasoline or acetone to clean the product. Never dry the trimmer teeth with a towel or tissue, as this may damage the trimmer teeth.

After every use: cleaning under the tap

1. Turn off the product and disconnect from the power outlet.

2. Remove any guard or cutting element (see ‚Detaching and attaching cutting elements‘) from the product.

3.  Rinse the hair chamber under a warm tap.

4. Clean the cutting element and guard under a warm tap (Fig. 23).

5. Carefully shake off excess water and let all parts air dry completely.
   Thorough cleaning

6. Turn off the product and disconnect from the power outlet.

7.  Wipe the handle of the product with a dry cloth.

8. Remove any guard or cutting element (see ‘Detaching and attaching cutting elements‘) from the product.

9. Remove any hairs that have accumulated in the hair chamber with the cleaning brush supplied.

10.  Remove any hairs that have accumulated in the cutting elements and/or guards with the cleaning brush supplied.

11.  Clean the cutting elements under a warm tap (Fig. 23).

12. Clean the guards under a warm tap (Fig. 23).

13.  Carefully shake off excess water and let all parts air dry completely.

Cleaning the nose trimmer

1. Clean the nose trimmer immediately after use and when a lot of hair or dirt has accumulated on the nose trimmer head.
   Rinse the nose trimmer head with hot water (Fig. 24).

2. Turn on the product and rinse the nose trimmer head once more to remove any remaining hairs. Then turn off the product again.

For a thorough clean, immerse the nose trimmer head in a bowl with warm water for a few minutes and then turn on the product to remove stubborn hair/debris.

Carefully shake off excess water and let all parts air dry completely.
Cleaning the precision shaver

1.  Hold the precision shaver at the grooves on each side and pull the top part off the bottom part (Fig. 25).
2.  Blow and/or shake out any hair that has accumulated inside the precision shaver (Fig. 26).
3.  Clean the top part of the precision shaver under a warm tap (Fig. 27).
4.  Carefully shake off excess water and let all parts air dry completely.
5.  Reattach the top part onto the bottom part of the precision shaver.
   This product has no other user-serviceable parts. For assistance call 1-800-243-3050.

Storage

• Store the product in the pouch supplied.
  Make sure the product is dry before you store it in the pouch.

•  Be sure the product is switched off. Remove the power cord from power outlet and the product before storing it in a safe, dry location where it will not be crushed, banged, or subject to damage.

• Do not wrap cord around the product when storing.

• Store cord and other accessories in a safe location where these will not be cut or damaged.

•  Do not place or store the product where it can fall or be pulled into a tub or sink, water or other liquid while plugged in.

Assistance
For assistance, visit our website:
www.philips.com/support or call toll free
1-800-243-3050.
Online information is available 24 hours a day, 7 days a week.

Disposal

•  This product contains a rechargeable lithium-ion battery which must be disposed of properly.
• Contact your local town or city officials for battery disposal information. You can also call 1-800-822-8837 or visit www.call2recycle.org for battery drop-off locations (Fig. 28).
• For assistance, visit our website www.philips.com/support or call 1-800-243-3050 toll free.
• Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. For recycling information, please contact your local waste management facilities or visit www.recycle.philips.com.

Full Five-Year Warranty
Philips North America LLC warrants this new product (except foil, cutters and guards) against defects in materials or workmanship for a period of five years from the date of purchase, and agrees to repair or replace any defective product without charge.

IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse, lack of reasonable care, the affixing of any attachment not provided with the product or loss of parts or subjecting the product to any but the specified voltage or batteries.*
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

In order to obtain warranty service, simply go to www.philips.com/support for assistance. It is suggested that for your protection you return shipments of product by insured mail, insurance prepaid. Damage occurring during shipment is not covered by this warranty.

NOTE: No other warranty, written or oral, is authorized by Philips Personal Health, a division of Philips North America LLC.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion and limitations may not apply to you.
*Read enclosed instructions carefully.

45-DAY MONEY-BACK GUARANTEE

• If you are not fully satisfied with your product send the product back and we’ll refund you the full purchase price.
• The product must be shipped prepaid by insured mail, insurance prepaid, have the original sales receipt, indicating purchase price and date of purchase, and the money-back guarantee return authorization form enclosed.
• We cannot be responsible for lost mail. The product must be postmarked no later than 45 days after the date of purchase. Philips reserves the right to verify the purchase price of the product and limit refunds not to exceed suggested retail price.
• To obtain the money-back guarantee service, please go to www. PhilipsMoneyBack.com and follow the simple 3-step process.

Delivery of refund check will occur 6–8 weeks after receipt of returned product.

Norelco is a registered trademark of Philips North America LLC.
PHILIPS and Philips shield are registered trademarks of Koninklijke Philips N.V.
©2022 Philips North America LLC. All rights reserved.
4222.002.8789.3 (01/27/2022)

References

• Philips Consumer Product Return and Refunds - Cookies Required
• Call2Recycle | Leading the Charge For Battery Recycling
• Product registration | Philips
• Philips Customer Service Support - Home | Philips

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>