COSTWAY TL35285 Folding Miter Saw Stand User Manual

: June 6, 2024
: COSTWAY

Table of Contents

Parts
Safety Instructions
Hardware & Parts
Assembly Instructions
Attach the Wheels
Set-up / Knockdown Procedure
One Year Limited Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

COSTWAY TL35285 Folding Miter Saw Stand User Manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Congratulations
You have just purchased a PM3900 Folding Saw Stand. This product has been specifically designed to assist you in the use if your 10-12 miter saw.

Parts

Kit No. J-104
Mounting Kit for Miter Saws and/or Other Power Tools with an Inset Mounting Hole Pattern

Kit No. J-210
Mounting Kit for Miter Saws and/or Other Power Tools with 3-Hole Mounting Pattern Comes with everything above and adds bracket (Part #J105) which connects both #3040 Offset Mounting Brackets.

Instructions
Secure Offset Mounting Brackets as shown above. Note: Brackets can be used on the front or rear of the Machine Mounts.

Safety Instructions

General Safety Instructions for Power Tools

Using power tools of any kind can be dangerous if safe operating procedures are not followed. Recognizing the hazards of each tool and using them with respect and caution will considerably limit the possibility of personal injury. However, if safety precautions are ignored, personal injury will likely result. Always use common sense — your personal safety-is your responsibility. Know your power tool. Read and understand the Operator’s Manual and observe the warnings and instruction labels affixed to the tool.

Safety Instructions for Miter Saw Stands

Use caution when folding or unfolding legs to limit any finger pinch points.
Place stand on flat and level surface to keep tool from rocking or Upping.
Make certain that work support extensions are within safe operating limits, and are properly locked in place before using tool. Do not exceed 300 lbs. on main frame table.
Test the setup for stability before proceeding with work.
Be sure the miter saw is tightened securely at all mountings before use.

Hardware & Parts

Note: Hardware and parts shown are actual size.

Hardware & Parts

Assembly Instructions

Read all assembly instructions completely before attempting assembly. See parts list for names and pictures of parts. Identify all components and hardware.

Install Leg B as shown in Figure 1 to Top Frame A and secure with 1/4″ – 20 x 1-3/4″ Bolt G and 1/4″ Lock Nut H. Insure that Snap Pin is facing out and securely latches in the open and closed positions. Do not over tighten. Repeat on remaining three Legs.
Note: The two legs with the additional 4 holes need to be mounted on the same end of the Top Frame.
Place top frame upside down on your workbench or work surface. Open the legs by depressing the snap pins and pivot the legs into the open position.
Install the Outrigger Supports D into the Top Tube as shown in Figure 2.
Install (4) 5/16″ – 18 3-Point Knobs J into the threaded holes in the Top Tubes and Outrigger Supports D.
Install Support T’s E into the ends of the Outrigger Supports D. Figure 3.
Locate the machine mounts (Part# 3042). Carefully review Figure 4. Note the location of the spring mounted handles; these should be positioned to the rear of the saw as shown. This allows for easier installation and removal of the saw.
Attach the (2) machine mounts to the saw using 5/16″-18 x 2-1/2″ carriage bolts K at each saw mounting point. See Figure 5. From the bottom, pass the carriage bolt through the slot in the machine mount, through the mounting hole and secure with 5/16″ flat washer M, lock washer N and nut L. Hand tighten only.
Carefully lift the saw and place onto the miter saw stand. Be sure the hook end of the machine mount locks under the top tube as shown in Figure 6. The spring loaded handle should lock under the opposite top tube as shown in Figure 7.
Slide the saw forward or back along the machine mount to best balance the saw on the stand. Secure the saw by tightening the carriage bolts installed in Step 7.

Attach the Wheels

Attach the axle brackets R to the outside of the leg using (2) 1/4-20 x 1-3/4″ Hex Bolts G and (2) 1/4-20 Nylon Lock Nuts H per leg. Align the axle bracket holes with the holes in the leg so the axle will be parallel with ground when secured. Figure 8.
Slide the 6″ Wheel Q onto the axle. The integrated spacer on the wheel should face the leg. Secure in place with Latch Pin P. Figure 9.

Set-up / Knockdown Procedure

Remove the saw from the work stand.
Collapse the Extension Supports to minimum size.
Depress the snap button on each leg and fold the leg under the Top until the snap button pops into the closed position. Figure 10.

One Year Limited Warranty

Warrantor warrants to the original purchaser that the folding miter saw stand will be free from defects in materials and workmanship under normal use and service for a period of one (1) year from the date of original purchase.

The obligation of this Warranty is limited to repair or replacement, at our option, of components which prove defective under normal use.

Any product or component claimed to be defective should be sent during Warranty period, together with a copy of your original dated sales receipt. Call for authorization number before sending.

This warranty is in lieu of all other express warranties, obligations or liabilities. ANY IMPLIED WARRANTIES, OBLIGATIONS OR LIABILITIES, SHALL BE LIMITED IN DURATION TO THE ONE YEAR PERIOD OF THIS LIMITED WARRANTY. NO AGENT, REPRESENTATIVE, DEALER, OR EMPLOYEE OF THE COMPANY HAS THE AUTHORITY TO INCREASE OR ALTER THE OBLIGATIONS OF THIS WARRANTY.

This Warranty shall not apply to any product or component which in the opinion of the Warrantor has been modified or altered in any way, damaged as a result of an accident, misuse or abuse, or loss of parts. In no case shall the Warrantor be liable for any special or consequential damages, or any other costs or warranty, expressed or implied, whatsoever.

This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Welcome to visit our website and purchase our quality products!

Your suggestions and comments for COSTWAY are really important to us! We sincerely solicit you to go back to our shop and leave a good rating in just a simple click. It would be quite encouraging if you could kindly do so like below:

Great products so far

February 24, 2019
Great products so far. Fast delivery, easy setup, and working without any issues.

With your inspiring rating, COSTWAY will be more consistent to offer you EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE!

US office: Fontana, California
UK office: Ipswich