DEITY MICROPHONES BP-TRX Connect Timecode Single-Channel Wireless Kit Instruction Manual
- June 6, 2024
- DEITY MICROPHONES
Table of Contents
DEITY MICROPHONES BP-TRX Connect Timecode Single-Channel Wireless Kit
Foreword
Thank you for puuhaslng the Deity Connect Tlmecode Kit.
Instructions
- Please read this product manual careful)/.
- Keep this product manual. Always include this product manual when passing the product on to third parties.
- Heed all warnings and follow all Instructions In this product manual.
WARNING: Do not place the product near any corrosive chemicals. Corrosion may cause the product to malfunction.
- Only use a microfiber or dry cloth to dean the product,
- Operate carefully – dropping or hitting the product may c:au,e damage.
- Keep all liquids away from the product. Liquids entering the product can short-circuit the electronics or damage the mechanics
- Store the product In a dry, clean, dust-free environment.
- If your product malfunctions, please have Tt serviced by an authorized shop. The warranty does not cover repairs to devices that have been subjected to unauthorized disassembly, although you may re<:1uest such repairs on a chargeable basis.
- The product is certified by RoHS,CE, FCC, KCC and Japan MIC. Please adhere to the operation standards. The warranty does not cover repairs arising out of the misuse of the product, although you may request such repairs on a chargeable basis.
- The instructions and information in this manual are based on tharough, controlled company testing procedures. Further nolicewlll not be given If the design and specifications change.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions;
(1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limit; are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation, If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorientate or relocate the receiving antenna.
- Increase the distance separating the equipment and receiver.
- Connect the device to a different power supply than that which the receiver Is connected to.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used In portable exposure condition without restriction.
Intended Use
Intended use of the Deity Connect Timecode Kit includes:
- The user has read the Instructions of this manual.
- The user is using the products within the operating conditions and limitations described in this product manual.
- ‘Improper use” means using the products other than as described in these instructions or under operating conditions that differ from those described herein.
Item checklist
Package includes the following items:
Nomenclature
Installations and Use
Antenna Installation
“When installed, the BP-MX antenna points away from the body (belt dip), which helps improve the transmission range.
Lavalilier Microphonl! Installation
The BP-TRX has a locking 3.5mm TRS connection. Simply clip the Lavalier
Microphone onto your clothes and screw it into the BP-TRX TRS microphone
input.
Use of the BP-TRX Belt Clip
The BP-TRX can be attached to the user’s belt or clothing via the included
belt clip.
Functions and Operations
On/Off /Back Button
Long press to turn the BP-TRX on and off. It also functions as a #back” button
while navigating the various menus and setup screens to return to the previous
screen or menu item.
MENU/SEL Button
This button is used to enter the menu and select highlighted items.
Up/Down Buttons
The Up and Down buttons are used to select various options and adjust
values In the setup screens.
- When the screen is locked, press the Up and Down buttons simultaneously for 3 seconds to unlock the screen.
- When recording, the up/down buttons can increase/decrease the microphone gain.
- When playing back audio files, the up/down buttons can increase/decrease volume.
- Playing back the audio file, long press the up/down button can switch to the fast/next audio file.
Language Setting
Enter the LANGUAGE” option in the SYSTEM SET menu to select the language
(system default English].
TRX Mode Selection
Short press the MENU/SEL Button to enter the ‘TRX mode” option for
selecting the working mode of BP-TRX according to your needs, there are seven
mode options: TX+REC, RX MODE, MASTER TX, IEM MODE, CAMERA HOP, TC BOX, REC
ONLY.
TX+REC: The BP-TRX will act as a transmitter with built in recording. By
pressing the REC button on the unit [or on a paired BP-TRX set to receiver, or
the UP-button of the DUO-RX) the recorder will start or stop. Pre- jammed SMTP
timecode will be stamped In the header of the BWF-1ile. The USB port will
output digital audio
(USB-C AD-converter).
RX: The BP-TRX will act as a receiver. The REC button controls the recorder on the paired BP-TRX or the HD-TX. The paired TX can be controlled via the receiver menu.
MASTER TX:The unit can pair up to 4 BP-TRXs (set to IEM or CAMERA HOP MODE). The internal recording on the MASTER TX can also be used simultaneously. Pre- jammed SMTP timecode will be stamped in the header of the BWF-file.
IEM: The unit can pair with the BP-TRX (set to Master TX mode) and will receive the audio. Four units can be paired to one Master TX. (IEM = In Ear Monitor).
CAMERA HOP: The unit pair with the the BP-TRX (set to Master TX mode) and will receive the audio. Four units can be paired to one Master TX. The output can be a combination of timecode and audio, or audio only.
TC BOX: The unit will act as a stand-alone timecode device. Audio input supports timecode in for jam syncing. Audio output can output the timecode.
REC ONL Y:The unit will act as a stand-alone recorder with timecode. Prejammed SMTP timecode will be stamped in the header of the BWF-file. The USB port will output digital audio (USB-C AD-converter).
User ID Setting
Enter the “USER ID” option in the menu to set the BP-TRX’s User ID to identify
different BP-TRXs.
Pair Setting
The BP-TRX uses Easy-pair™ technology. After setting the working mode of BP-
TRX, 14. RF Power Setting enter the “PAIRH option in the Transmitter and
Receiver menu respectively, select “YES” to pair. The Transmitter and Receiver
will automatically finish the pairing within 15 seconds, and the Pair LEDs
flash green to indicate pairing. The green LEDs stay on to indicate that the
pairing was successful and if the green LEDs flash slowly, the pairing was
unsuccessful. Meanwhlle, a pop-up window will Indicate If your pairing was
successful or not.
Auto-lock Setting
Enter the “AUTO-LOCK” option in the SYSTEM SET menu to set the lock screen
time (system default 1 Ssl. There are nine options: never, 5s, 10S, 15s, 20s,
1 min, 2min, 5min, 10min.
When the screen is locked, the buttons will not work This helps to prevent settings from changing during operation. To unlock the screen, press the Up and Down buttons simultaneously for 3 seconds.
Input Type! Setting
The BP-TRX has two input modes: STEREO mode and MONO mode. Please select the
Input Type according to the audio source selected. Use STEREO mode if you are
feeding a stereo signal into the BP-TRX.
Input Gain Setting
Enter the “INPUT GAIN ” option in the BP-TRX menu to increase or decrease the
audio gain as needed (matches the Transmitter gain with the audio’s output
level, the user’s voice level and the position of the microphone). The
adjustment range is from -12dB to +36dB in 3dB steps.
File Management
Enter the “FILE” option in the BP-TRX menu. The BP-TRX allows you to
playback files, rename them, and delete takes.
Mute Setting
Enter the “MLITE” option in the BP-TRX menu to turn the mute function on or
off as needed. When “MUTE-ON’ is set in the “HOTKEY” menu of SYSTEM SET, you
can
also quickly the mute function on or off by short pressing al• at the main
screen.
- When muted, the mute LED will flash red slowly.
System Reset
Enter the ‘SYS RESET” option in the menu to reset the system and restore the
default settings.
Firmware Update
Users can update firmware via U disk[exFaVFAT32 USB flash drive). When
updating the firmware, please download the latest firmware to the root
directory of U disk on the official website, then use the “USB-C to USB-A
Firmware Update Adapter” to connect the U disk to the USB Type-( input port,
select “UPDATE” option from the menu, and update the 1irmware following the
on-screen instructions. After the firmware update is completed, the firmware
version shows the latest version. Official website: https://www.deitymic.com
- BP-TRX also surf)Qrts firmware update via built-in MicroSD card.
Data/Time Setting
Enter the “DATE/TIME” option in the SYSTEM SET menu to set the specific date
and time of recording.
Record/Stop Button
After inserting the Micro SD card into the BP-TRX, short press the NREC/ STOP”
button to start or stop recording audio files in TX or REC ONLY mode.
The BP-TRX units sold inside the USA will disable audio transmission when you
hit record. Only internationally sold units will feature the ability to
transmit and record simultaneously.
- Max Card Size – 128Gb
- Card Type- microSD
- Card Format- FA T32, exFAT
- Max Fife Size -2Gb automatically keeps recording and creates new file
- File Type-24blr:/48kHz Uncompressed PCM WAV file
Pause/Play Button
Short press the “PAUSE/PLAY” button to play or pause the audio file recorded
on the microSD card.
TX Remote Setting
After the Transmitter and Receiver are successfully paired, enter the “TX
REMOTE” menu, then users can remotely control every audio adjustment on the
Transmitter through the Receiver.
TX Sleep Setting
After the Transmitter and Receiver are successfully paired, users can set
whether the Transmitter sleeps or not in the Receiver menu. When the sleep is
turned on, the Transmitter enters a low power mode (locks screen, powers down
the audio input circuitry, but keeps feeding a low power data stream to
maintain the link).
Out Level Setting
Enter the “OUT LEVEL’ option in the BP-TRX Receiver menu to adjust the output
gain as needed. The adjustment range is from -24dB to +24dB in 1 dB steps.
Out Type Setting
When the BP-TRX working mode is selected as the RX MODE, BP-TRX has four
output type options: XLR, DSLR, HOP, and SYNC.
When the BP-TRX working mode is selected as the CAMERA HOP mode, BP-TRX has
two output type options: MONO and SYNC. Please set the output type according
to your needs.
Latency Setting
Enter the ‘LATENCY’ option in the Receiver menu to select the latency setting
(LOW, MID, HIGH) according to the actual recording needs. Users can optimize
the transmission distance between the Transmitter and Receiver.
Charging
The power LED glows green when the battery is good. The color changes to red
when there is about 30 minutes of operation left. The BP-TRX supports Qualcomm
QC
2.0/3.0 and MTK PE quick charge. The battery is charged using the included
Type-C charging cable connected to a DC adapter (Not included).
- When charging, the power LED will flash between red and green.
- When fully charged, the power LED stays green.
Timecode
-
Timecode overview
The BP-TRX comes with an internal crystal based timecode generator. Timecode functionality will be available in the following TRX modes:TX+REC. RX MODE, MASTER TX, CAMERA HOP, TC BOX, REC ONLY.
Timecode is time information written to data when recording video and audio. It is used for video editing, control of other devices, and synchronization of audio and video. If video and audio data both have recorded timecodes, aligning them to a timeline and synchronizing them together is easy when using nonlinear editing software.
” The product uses a precision oscillator that genera res timecode with a high degree of accuracy(+/- 0.5 ppm, or approximately 1 frame per 24 hours).
-
Timecode mode setting
The timecode mode settings allow you to specify whether the BP-TRX generates timecode or not. An internal timecode will be generated only when recording or
regardless of the recording mode.
Short press MENU SEL button, select TC SYNC, press MENU SEL to enter timecode setting interface. Select the mode, press MENU SEL to select the mode you required.
-
Frame rate setting for internal timecode
You can set the frame rate for internal timecode as 23.976, 24,25, 29.97, 29.97DF, 30,30DF. DF stands for Drop frame.
Short press MENU SEL button, select TC SYNC, press MENU SEL to enter timecode setting interface. Select the FPS, press MENU SEL to select the FPS you required.
Matching frame r.ites must be set in adv.ince on all connected video and .iudio devices. -
Timecode jamming operation
-
Jamming external timecode
You can use the included timecode sync & audio cable to jam the BP-TRX to an external timecode . Continue to below steps:
Short press MENU SEL button, select TC SYNC, press MENU SEL to enter timecode setting interface. When external timecode input is detected. Select JAM to sync the internal and external timecode. -
Jamming internal timecode
The Audio output can be engaged to give a timecode source, to connect or jam other devices, such as recorders, cameras, other BP-TRX units or third party timecode devices.
You also can use included time code sync & audio cable or TRS cable to connect BP-TRX audio output jack to external timcode input jack. Perform the time code synchronization operation as follows:
lf TRX MODE sets as RX MODE or CAMERA HOP MODE, select the OUT TYPE as SYNC, press the Up or Down buttons to select TC SYNC, press MENU SEL button to select Jam to synchronize the timecode.
lf TRX MODE is set to TX+REC
MODE/MASTER TX MODE/TC BOX/REC ONLY, press MENU SEL button, select TC SYNC,
press the down button to select OUTPUT as ON. Select Jam to synchronize the
timecode. If other modes, skip this step.
“‘ ffTRX MODE is set to /EM MODE, there is no timecode output. -
Restarting the internal timecode with a specified value
Press MENU SEL to select Restart” and press MENU SEL. Set the restart value.
Move cursor or change value, press UP/Down button.
Select parameter to change, press MENU SEL button.
M ff timecode mode Is set to Int RTC Run, we cant restart the internal tlmecode. -
Timecode level setting
To accommodate a certain TC level needed by a particular connected device, and if ExtTC is not detected during timecode synchronization, the BP-TRX can increase or decrease the voltage level of timecode output to make it to be detected . The adjustment range is from 0.SV to 3.0V in 0.1V steps. The system defaults to 2.SV.
Specifications
Icon Description
Documents / Resources
|
DEITY MICROPHONES BP-TRX Connect Timecode Single-Channel Wireless
Kit
[pdf] Instruction Manual
2AABZ-DEITY, 2AABZDEITY, BP-TRX Connect Timecode Single-Channel Wireless Kit,
BP-TRX, Connect Timecode Single-Channel Wireless Kit
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>