elero Combio-868 LI Built In Radio Receiver for Lighting Systems Instruction Manual
- October 27, 2023
- elero
Table of Contents
elero Combio-868 LI Built In Radio Receiver for Lighting Systems Instruction Manual
Translation from the original German version. All other documents in different languages are translations of the original version.
All rights reserved in the event case of patent, utility model or design registrations.
1 Introduction
This user manual describes the functions and features of the Combio-868 LI system. Combio-868 LI enables appropriate illuminants to switched and dimmed. Appropriate illuminants are as follows:
- standard light bulbs
- high-voltage halogen light bulbs
- low-voltage light bulbs with electronic transformer
- LED light bulbs with a suitable electronic dimmer (ECG, electronic control gear)
An elero handheld/wall-mounted transmitter (at least 1) is also required. The Combio-868 LI can be controlled by several transmitters.
Follow the instructions in these manuals to ensure proper and safe use.
Retain for future use.
1.1 Manufacturer contact details
elero GmbH
Maybachstr. 30 73278 Schlierbach – Germany
Telephone: +49 (0)7021 9539-0
Email: info@elero.de
Website: www.elero.de
1.2 Symbols and warnings
This user manual uses the following illustrations to display important warnings:
WARNING
Danger with a medium level of risk, possibly resulting in death or serious
injury.
ATTENTION
Danger, possibly resulting in damage to property.
2 Safety instructions
2.1 Target group
This document is primarily intended for use by electricians, technicians and engineers with experience in the design, installation, commissioning and maintenance of building technology.
2.2 Intended use
This product is for private use only. It is intended only for the switching and/or dimming of suitable illuminants for use in dry rooms. The Combio-868 LI is designed for installation in dry cavities in buildings. Do not perform any modifications to the device. The manufacturer will not assume liability for damage caused by the above. Do not operate a programmed transmitter inadvertently or carelessly.
2.3 Warranty
- The warranty period for Combio-868 LI is in accordance with the legal regulations. Damages caused due to improper use are excluded.
- Never open the device without authorisation. Opening the housing renders the warranty null and void.
- No warranty claims may be made for damage caused to the Combio-868 LI due to improper operation resulting from non-observance of the operating instructions or due to a disregard of these instructions.
- No liability shall be accepted for consequential damages.
3 System description
3.1 Application area
Combio-868 LI enables the switching and dimming of suitable illuminants in combination with elero hand-held/ wall-mounted transmitters.
3.2 Terminal connection diagram
The illuminants that are connected are powered and activated via suitable clips by means of same-coloured connections.
4 Technical data
5 Preparation
5.1 Product contents
5.2 Packaging
Packaging is designed for protection of the Combio-868 LI during transport. After unpacking, please check all components delivered for completeness or damage.
5.3 Settings
The equipment is set via the elero handheld/wall-mounted transmitter following the electrical connection.
5.4 Connection and installation
WARNING
Risk of injury, damage to the Combio-868 LI and its surrounding area due to
improper electrical connections.
WARNING
- The electrical connection may only be conducted by qualified personnel.
- Only perform work on the electrical connection if it has been disconnected from the power supply.
- Note the technical data for the device.
- Take care to ensure correct, securely affixed connections.
- Screw the Combio-868 LI to the surface by means of the ring lug using a suitable screw.
- Affix the Combio-868 LI using a self-adherent foam strip.
- Do not kink, shorten or extend the external antenna of the Combio-868 LI, route it as free from obstruction as possible. Do not lay it against metal. Realign it in case of poor reception.
ATTENTION
Replacing components of the Combio-868 LI with third party components may
damage these components or other connected systems.
- Exchange components between different systems only after consultation with the manufacturer or your supplier.
- When replacing a component, check whether the type description of the new component matches the one being replaced.
5.5 Commissioning
The elero handheld/wall-mounted transmitter has to be programmed to the
Combio-868 LI radio receiver.
The functions of the Combio-868 LI are controlled using the buttons [OPEN ],
[STOP ], [DOWN ], programming button [P] and the slider of the handheld/ wall-
mounted transmitter.
The + sign in the text indicates pressing the buttons simultaneously.
5.6 Diagram of programming mode
5.7 Asynchronous programming mode (standard)
Asynchronous programming mode is the standard programming mode. In
asynchronous programming mode, the switch-on duration of the ON times vary in
case of several receivers. After a few ON/OFF cycles, the illuminants of the
receivers will no longer light up synchronously. This will enable the hits for
a certain receiver to be set better.
Asynchronous programming mode is suitable for
- programming the first transmitter
- programming an additional transmitter
- programming individual receivers in case of several receivers ready for programming (e.g. several receivers using one fuse).
- Programming can only ever be performed in one selected channel.
- When programming is complete or after 5 minutes has passed, the receiver will revert to normal operation.
- Programming mode can be stopped by pressing the [STOP ] button for at least 6 seconds.
- Up to 16 transmitters can be programmed.
- Several receivers can be programmed to one channel.
- If more than 10 receivers at once are in programming mode, the transmitter changes to group programming mode. Once programming is complete, group programming mode has to be terminated manually in the transmitter by pressing the [STOP ] button for at least 6 seconds.
5.8 Synchronous programming mode
Synchronous programming mode is a special programming mode. In synchronous
programming mode, the switch-on duration of the ON times will be constant with
several receivers. Even after a few ON/OFF cycles, the illuminant of the
receivers will light up synchronously. As a result, the hits for all
participating receivers can be set simultaneously.
Synchronous programming mode is suitable for
- programming an additional transmitter
- programming several receivers simultaneously to one transmitter or one channel.
- Programming can only ever be performed in one selected channel.
- When programming is complete or after 5 minutes has passed, the receiver will revert to normal operation.
- Programming mode can be stopped by pressing the [STOP ] button for at least 6 seconds.
- Up to 16 transmitters can be programmed.
- Several receivers can be programmed to one channel.
- If more than 10 receivers at once are in programming mode, the transmitter changes to group programming mode. Once programming is complete, group programming mode has to be terminated manually in the transmitter by pressing the [STOP ] button for at least 6 seconds.
6 General control options
6.1 Adapting an illuminant
The factory setting of the Combio-868 LI allows a power setting between 10%
and 100%. The power cannot be set below 10%. Some illuminates require more
than 10% of the power at the lowest operating limit. This could lead to the
illuminant not lighting up yet a low level of current flowing regardless. In
such cases the absolute lower dimming limit should be adapted to the
illuminant.
When adapting an illuminant, the absolute lower dimming limit can be set or
this can be reset to the factory setting (10%).
In addition the Combio-868 LI can also be configured as a light switch.
6.2 Deleting the programmed handheld/ wall-mounted transmitter
Deleting a transmitter does not effect the brightness values set. Deleting a transmitter will cause the factory setting to be restored.
7 Servicing
7.1 Cleaning
The components of the Combio-868 LI do not require any special cleaning providing they are protected inside an installation box against dirt.
7.2 Maintenance
The Combio-868 LI is maintenance-free.
7.3 General notes on troubleshooting
7.4 Repairs
Damaged Combio-868 LI components may only be repaired by the manufacturer. If necessary, contact your supplier.
8 Decommissioning and disposal
8.1 Disassembly
WARNING
Risk of injury and damage due to unconnected electrical cables.
- The electrical connection may only be modified by qualified personnel.
- Only perform work on the electrical connection if it has been disconnected from the power supply.
- Ensure that any connecting cables that have been removed are not left unprotected (insulate).
If intending to remove the Combio-868 LI, proceed as follows:
- Switch off the power supply.
- If the components have been installed in an installation box, remove them.
- Disconnect all connected cables.
8.2 Disposal
The Combio-868 LI must be disposed of in accordance with the legal regulations
for electronic devices.
♻ The packaging must be disposed of separately in accordance with the
applicable rules for cardboard and plastic.
9 Certification and imprint
9.1 EU Declaration of Conformity
elero GmbH hereby declares that the Combio-868 LI is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following Internet address: www.elero.com/downloads- service/downloads
9.2 Legal Disclosure
elero GmbH
Maybachstr. 30
73278 Schlierbach – Germany
Telephone: +49 (0)7021 9539-0
Email: info@elero.de
Website: www.elero.de
WEEE-Reg.-No. DE 26410414
All rights reserved. All copyrighted names and trademarks mentioned (such as product names, logos, business names) are protected for the respective right owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>