Roumi Technology MN02 Magnetic Wireless Charger User Manual
- June 6, 2024
- Roumi Technology
Table of Contents
Roumi Technology MN02 Magnetic Wireless Charger
OVERVIEW
Please read the instructt0ns before using the product
Parameter specification
- Model: CWXCS30
- In put volage/cu rrent DCS.0V /2.0A,9.0V /2.0A, 12V /1.SA Output power: lSW(Max)
- Charging frequency: 11020sKHz
- Transmission Distance: Smm
- Efficiency: 75%
- Scope of application: For iPhone 12 series
- Material:( PC+ ABS )plastic
- Dimention;L81.S”W61.SD82mm
Installation of air outlet bracket
- Loosen the nut 1. then buckle the base bracket into the mobile phone bracket tighten lhe nut to make it i.:l whole, and rotate the mobile phone Holder to adjust the visual angle or the vehicle bracket 360 degrees freely
- Push for.,vard the clamp to lock of the base bracket. put the clip into the air outlet of the car and faslen it tightly wit 1 the blade.
- The fixed bracket is used to support and stabilize the bracket. The anti-skid part of sif1ca gel 1s close to the arr outlet. Pay attention to the installation direction.
Connect the power cord
(Connect one end of the USB-C interface of the USB cable to the magnetic wireless charging USB-C interface. Insert the USS cable USB,A into the USB socket of the car charger
Remarks
- The manncI·c suct; o , on o, the w1re!oss charger only StJpports 1Phonc- 12112 mini/12 pro.112 pro-Max Series
- The standard support 9Vi12V car charger can support the fast cr-a,ging function of th·s product, and Ihe car charger needs 10 be purchased separately
Important notes
When 1he wireless charger,s ch<.irging for the rnob1·c <lev1ce, 11 you run a powor·consuming appl on the mobile device or use the ..applicant; On on the device for a long time, !he mobile device wil heats up. This is a normal phenomenon and w II does not affect the sc or performance of the dev, co.
- This product only supports original Apple pro1cctive covers. can not Quarantc-e to be compatible,·.-.It has 1hird-party magnet accessories.
- When 1he bracket is installed to the air outlet, the 1-xod b1ackc1 should be adjusted to the appropriate pos,Iron, and the anIi-sk1d s:silica gel should be used 10 fix the air outlet to prevent shaking
- Ad1us1 the mob le phone bracke1 10 the ideal and e before placing the mob<le phone
- The bracket does not suppor1 tan-shaped air outlet
- The equipment can be used between O C · 35·C, and can be stored between -20·C and 50 C. If the device,s used or stored outside the recommended temperature range,I1 may damage Ihe device.
- Pls, prevent 1he children or a mal viewing the eq,pl.
- Do no! disassemble, mod ly or repair the equipment
- Do not place magnetic stripe cards (including cred,< cards, phone cards. bank books and reg,stra1ion cards) near the charging device to avoid damage from the magnetic f eld generated by the device.
Recommend to use with Apple original phone case
Warranty
There Is a one-year guarantee tor lots product unless anthropogenic factor.
Packing List
- Magnct·c wireless charge-r 1C1
- USB·C C<1b’C- x1
- User Manual x 1
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. During the operation of device, a distance of 15 cm
surrounding the device and 20 cm above the top surface of the device must be
respected
Warning : Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>