RIDGID R5013 Drill VSR 1-2-Inch Hammer User Manual

June 5, 2024
RIDGID

RIDGID logo

OPERATOR’S MANUAL
MANUEL D’UTILISATION
DOUBLE INSULATED
DOUBLE ISOLATION
DOBLE AISLAMIENTO
R5013

To register your RIDGID
product, please visit:
http://register.RIDGID.com

INCLUDES: Hammer Drill, Auxiliary HandleOperator’s manual

WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
SAVE THIS MANUAL FOR FUTURE REFERENCE

GENERAL POWER TOOL SAFETY WARNINGS

WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
WORK AREA SAFETY

  • Keep work area clean and well lit. Cluttered or dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
  • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

  • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
    matching outlets will reduce risk of electric shock.

  • Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

  • Do not expose power tools to rain or wet conditions.
    Water entering a power tool will increase the risk of electric shock.

  • Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
    or entangled cords increase the risk of electric shock.

  • When operating a power tool outdoors, use an exten- sion cord suitable for outdoor use. The use of a cord suit- able for outdoor use reduces the risk of electric shock.

  • If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI)  protected supply.
    Use of a GFCI reduces the risk of electric shock.

PERSONAL SAFETY

  • Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
  • Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
  •  Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
  • Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
  • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
  • Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
  • If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
  • Do not wear loose clothing or jewelry. Contain long hair. Loose clothes, jewelry, or long hair can be drawn into air vents.
  • Do not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the power tool in unexpected situations.

POWER TOOL USE AND CARE

  • Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
  • Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
  • Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
  • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
  • Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
  • Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

GENERAL POWER TOOL SAFETY WARNINGS

  • Use the power tool, accessories and tool bits etc.in accordance with these instructions, taking into account the working conditions and the work to be
    performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

SERVICE

  • Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
  • When servicing a power tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury.

HAMMER DRILL SAFETY WARNINGS

  • Wear ear protectors with impact drilling. Exposure to noise can cause hearing loss.
  • Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
  • Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
  • Know your power tool. Read operator’s manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.
  • Always wear eye protection with side shields marked to comply with ANSI Z87.1. Following this rule will reduce the risk of serious personal injury.
  • Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will reduce the risk of serious personal injury.
  • Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule will reduce the risk of serious personal injury.
  • Inspect tool cords periodically and, if damaged, have repaired at your nearest authorized service center. Constantly stay aware of cord location. Following this rule will reduce the risk of electric shock or fire.
  •  Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center. Following this rule will reduce the risk of shock, fire, or serious injury.
  • Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gauge size (A.W.G.) of at least 14 is recommended for an extension cord 50 feet or less in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
  • Inspect for and remove all nails from lumber before using this tool. Following this rule will reduce the risk of serious personal injury.
  • If the power supply cord is damaged, it must be replaced only by the manufacturer or by an authorized service center to avoid risk.
  • Save these instructions. Refer to them frequently and use them to instruct others who may use this product. If you loan someone this product, loan them these instructions also.

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING
**** DANGER: Indicates a hazardous situation, which, if not avoided,

will result in death or serious injury.
**| WARNING:| Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
**
| CAUTION:| Indicates a hazardous situation, that, if not avoided, may result in minor or moderate injury.
| NOTICE:| (Without Safety Alert Symbol) Indicates information considered important, but
not related to a potential injury (e.g. messages relating to property damage).

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION
**** Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual To reduce the risk of injury, user must read and

understand operator’s
manual before using this product.
| Eye Protection| Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
| Wet Conditions Alert| Do not expose to rain or use in damp locations.
| Hot Surface| To reduce the risk of injury or damage, avoid contact with any hot
surface
V| Volts| Voltage
A| Amperes| Current
Hz| Hertz| Frequency (cycles per second)
W| Watt| Power
min| Minutes| Time
| Alternating Current| Type of current
no| No Load Speed| Rotational speed, at no load
| Class II Tool| Double-insulated construction
…/min| Per Minute| Revolutions, strokes, surface speed, orbits etc., per minute

ELECTRICAL

DOUBLE INSULATION
Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation.  Double insulated tools do not  need to begrounded.
WARNING:
The double insulated system is intended to protect the user from shock resulting from a break in the tool’s internal wiring. Observe all normal safety precautions to avoid electrical shock.
NOTE: Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the tool to your nearest authorized service center for repair. Always use original factory replacement parts when servicing.
ELECTRICAL CONNECTION
This tool has a precision-built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not operate this tool
on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the tool does not operate when plugged into an outlet, double-check the power supply.
EXTENSION CORDS
When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the tool will draw. An
undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter’s Laboratories (UL) should be used.
When working outdoors with a tool, use an extension cord that is designed for outside use. This type of cord is designated with “WA” or “W” on the cord’s jacket. Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation.
**Ampere rating (on tool data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0  12.1-16.0
Cord Length Wire Size (A.W.G.)
--- ---
25 16 16 16 16 14
50 16 16 16 14 14
100 16 16 14 12 10

Used on 12 gauge – 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber, tools or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury.
WARNING:**
Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury.

FEATURES

PRODUCT SPECIFICATIONS
Input ………………………………….120 V, 60 Hz, AC only, 7.5 A
Switch …………………………………………………. Variable Speed
Hammer Speed ……………………………………. 0-51,000 BPM
No Load Speed ……………………………. 0-2,700 r/min. (RPM)

ASSEMBLY

UNPACKING
This product has been shipped completely assembled.

  • Carefully remove the product and any accessories from the box. All items listed in the Includes section must be included at the time of purchase.

WARNING:
Items in this Assembly section are not assembled to the product by the manufacturer and require customer installation. Use of a product that may have been improperly assembled could result in serious personal injury.

  • If any parts are damaged or missing, please call 1-866-539-1710 for assistance.

WARNING:
If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.
WARNING:
Do not attempt to modify this product or create accessories or attachments not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.

INSTALLING THE AUXILIARY HANDLE ASSEMBLY
See Figure 1, page 11.
An auxiliary handle is packed with the drill for ease of operation and to help prevent loss of control. The handle can be rotated 360°, and it can be mounted on either side
for right or left hand use.
To install the auxiliary handle assembly:

  • Loosen the handle assembly by turning the handle counterclockwise.
  •  Install the auxiliary handle assembly in the desired operating position.
  • Securely tighten by turning the auxiliary handle clockwise.
    Be sure the auxiliary handle is securely tightened against the depth stop clamp. This secures the depth stop rod at the desired depth of cut. It also secures the auxiliary handle.
    NOTE: For convenience and ease of starting threads, the hex nut has been trapped inside the molded slot in the auxiliary handle.

OPERATION

WARNING:
Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury.
WARNING:
Always wear eye protection with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:

  • Hammer drilling in concrete, brick, or other masonry
  • Drilling in wood
  • Drilling in ceramics, plastics, fiberglass, and laminates
  • Drilling in metals

CAUTION:
This drill is not intended to be used for mixing concrete, drywall, grout or other similar types of viscous mixtures. Failure to obey this caution could cause poor performance, possible injury, and will void your warranty.
SWITCH TRIGGER
See Figure 2, page 11.
To turn the drill ON, depress the switch trigger. To turn it OFF, release the switch trigger.
VARIABLE SPEED
The variable speed switch delivers higher speed with increased trigger pressure and lower speed  with decreased trigger pressure.
NOTE: You might hear a whistling or ringing noise from the switch during use. Do not be concerned; this is a  normal part of the switch function.
DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE)
See Figure 3, page 11.
The direction of bit rotation is reversible and is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch trigger for forward drilling. The drilling direction is reversed when the selector is to the right of the switch trigger. NOTICE:
To prevent gear damage, always allow the chuck to come to a complete stop before changing the direction of rotation.
To stop the drill, release the switch trigger and allow the chuck to come to a complete stop.
NOTE: The drill will not run unless the direction of rotation selector is pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods of time. Running at low speeds under constant usage may cause the drill to become overheated. If this occurs, cool the drill by running it without a load and at full speed.

TO INSTALL BITS
See Figures 4 – 5, page 11.

  • Unplug the drill.
  • Insert the chuck key and twist counterclockwise.
  • Open or close the chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of the chuck jaws.

WARNING:
Make sure to insert the drill bit straight into the chuck jaws. Do not insert the drill bit into the chuck jaws at an angle then tighten, as shown in figure 5. This could cause the drill bit to be thrown from the drill, resulting in possible serious personal injury or damage to the chuck.

  • Insert the drill bit.

  • Tighten the chuck jaws securely on the drill bit, using the chuck key provided.

  • Remove the chuck key.
    TO REMOVE BITS
    See Figure 4, page 11.

  •  Unplug the drill.

  • Loosen the chuck jaws using the chuck key provided.

  • Remove the drill bit.

  • Remove the chuck key.

OPERATION

USING THE AUXILIARY HANDLE ASSEMBLY
See Figures 6 – 7, page 12.
An auxiliary handle is packed with the drill for ease of operation and to help prevent loss of control. The handle can be rotated 360°, and it can also be mounted on the opposite
side for left hand use.
To adjust the auxiliary handle assembly,

  • Loosen the handle assembly by turning the handle counterclockwise.
  • Rotate the auxiliary handle assembly to the desired operating position.
  • Securely tighten by turning the auxiliary handle clockwise.

Be sure the auxiliary handle is securely tightened against the depth stop clamp. This secures the depth stop rod at the desired depth of cut. It also secures the auxiliary handle.
NOTE: For convenience and ease of starting threads, the hex nut has been trapped inside the molded slot in the auxiliary handle.
The depth stop rod helps control the depth of drilled holes.
NOTE: When properly installed, the teeth on the depth stop rod should be aligned with the teeth indicator on the depth stop clamp.
Adjust the depth stop rod so that the drill bit extends beyond the end of the rod to the required drilling depth.
When drilling holes with the depth stop rod installed, the desired hole depth has been reached when the end of the rod comes in contact with the surface of the workpiece.
SELECTING HAMMER MODE OR DRILLING MODE
See Figure 8, page 12. To adjust for type of drilling, slide the selector on top of the motor housing to hammer mode or drilling mode. The hammer mode symbol is on the right and the drill bit symbol is on the left. NOTE: The hammer drill has not been designed for reverse hammering. Use carbide-tipped bits and select hammer mode when drilling in hard materials such as brick, concrete, etc. Use carbide-tipped bits and select drill mode when drilling in materials with hard, brittle surfaces such as tile, etc. Use twist drills, hole saws, etc., and drill mode when drilling in soft materials.

LOCK-ON BUTTON
See Figure 9, page 12.
This drill is equipped with a lock-on feature, which is convenient for continuous drilling for extended periods of time.

To lock-on:

  •  Depress the switch trigger.
  •  Push in and hold the lock-on button, located on the side of the handle.
  • Release the switch trigger.
  • Release the lock-on button and the drill will continue running.
  • To release the lock, depress and release the switch trigger.
    If the lock-on feature is engaged during use and the drill becomes disconnected from the power supply, disengage the lock-on feature immediately.

WARNING:
Before connecting the drill to a power supply source, always check to be sure it is not in lock-on position (depress and release the switch trigger). Failure to ensure that it is not locked-on could result in accidental starting of the drill resulting in possible serious injury. Do not lock the switch trigger in applications where the drill may need to be suddenly stopped.
DRILLING/DRIVING SCREWS
See Figure 10, page 12.
WARNING:
Always use the auxiliary handle when using this tool to help resist torque reactions. Binding or stalling of this product could lead to serious personal injury.

  • Install the auxiliary handle.
  • Depress and release the switch trigger to be sure the drill is in the OFF position before connecting it to a power supply.
  • Check the direction of rotation selector for the correct setting (forward or reverse).
  •  Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates.
  • Plug the drill into power supply. Hold the drill firmly and place the bit at the point to be drilled, or where the screw is to be driven.
  • Depress the switch trigger to start the drill.
  • Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting. Do not force the drill or apply side pressure to elongate a hole. Let the tool do
    the work.

WARNING:
Be prepared for binding at bit breakthrough. When these situations occur, the drill has a tendency to grab and kick in the opposite direction and could cause loss of control when breaking through material. If not prepared, this loss of control can result in possible serious injury.

  • When drilling hard, smooth surfaces, use a center punch to mark the desired hole location. This will prevent the drill bit from slipping off-center as the hole is started.
  • When drilling metals, use a light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drilling action.
  • If the bit jams in the workpiece or if the drill stalls, stop the tool immediately. Remove the bit from the workpiece and determine the reason for jamming.

WOOD AND METAL DRILLING
For maximum performance, use high speed steel bits for wood or metal drilling. Select drilling mode. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
Wood Drilling

  • Increase the speed as the drill bit bites into the material.
  • When drilling through holes, place a block of wood behind the workpiece to prevent ragged or splintered edges on the back side of the hole.

Metal and Steel Drilling

  • Use a light oil on the drill bit to keep it from overheating.
    The oil will prolong the life of the bit and increase the drilling action.

  • Maintain a speed and pressure which allows cutting without overheating the bit. Applying too much pressure= will:

  • Overheat the drill;

  • Wear the bearings;

  • Bend or burn bits; and

  • Produce off-center or irregular-shaped holes.

  • When drilling large holes in metal, start with a small bit, then finish with a larger bit.

MASONRY DRILLING
For maximum performance, use carbide-tipped masonry impact bits or designated hammer drill bits when drilling holes in brick, tile, concrete, etc. Select hammer mode.

  • Apply light pressure at medium speed for best results in brick.
  • Apply additional pressure for hard materials such as concrete.
  • When drilling holes in tile, practice on a scrap piece to determine the best speed and pressure. Begin drilling at a very low speed to prevent the bit from slipping off the
    starting point.

MAINTENANCE

WARNING:
When servicing use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.
WARNING:
Always wear eye protection with side shields marked to comply with ANSI Z87.1 during product operation. If operation is dusty, also wear a dust mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommended using this product for extended work on these types of materials. However, if you do work with any of these materials, it is extremely important to clean the product using compressed air.
LUBRICATION
All of the bearings in this product are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required.
This product has a 90-Day Satisfaction Guarantee Policy, as well as a Three-year Limited Warranty. For Warranty and Policy details, please go towww.RIDGID.com or call (toll free) 1-866-539-1710.
NOTE: FIGURES (ILLUSTRATIONS) START ON PAGE 11 AFTER FRENCH AND SPANISH LANGUAGE SECTIONS.
RIDGID R5013 Drill VSR 1 2 Inch Hammer -
fig

A – Drilling/hammer mode selector
B – Depth stop rod
C – Chuck
D – Auxiliary handle assembly
E – Switch trigger
F – Direction of rotation selector
G – Lock-on Button
H – Chuck key strap
I – Power cord
J – Chuck key

A – Auxiliary handle assembly
B – To tighten
C – To loosen
D – 360° rotation

| A – Direction of rotation selector
B – Forward
C – Reverse|

WRONG / INCORRECT / FORMA INCORRECT

|

A – Hammer mode
B – Drilling mode
C – Drilling/hammer mode selector

|

A – To increase drilling depthB – To decrease drilling depthC – Depth stop rodD – Drilling depthE – Drill bitF – Auxiliary handleG – Depress here to adjust depth stop rod assembly

---|---|---|---|---
A – Lock-on button
B – Switch trigger|

RIGHT

A – Chuck key storage
B – To tighten
C – To loosen
D – Chuck key
E – Drill bit
F – Chuck jaws
G – Chuck

|

A – Auxiliary handle assembly
B – To tighten
C – To loosen
D – 360° rotation

|

A- Lock-on button
B – Switch trigger

|

NOTES ……………………
Customer Service Information:
For parts or service, do not return this product to the store. Contact your nearest RIDGID® authorized service center. Be sure to provide all relevant information when
you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at powertools.ridgid.com.
MODEL NO. ____SERIAL NO.___
Model number on product may have additional letters at the end. These letters designate manufacturing information and should be provided when calling for service.

ONE WORLD TECHNOLOGIES, INC.
P.O. Box 1427
Anderson, SC 29622 USA
1-866-539-1710 powertools.ridgid.com
RIDGID is a registered trademark of RIDGID, Inc., used under license.
987000-060
2-11-21 (REV:06)

Documents / Resources

| RIDGID R5013 Drill VSR 1-2-Inch Hammer [pdf] User Manual
R5013, Drill VSR 1-2-Inch Hammer
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals