COSTWAY EP24962USA Jump Starter User Manual
- June 6, 2024
- COSTWAY
Table of Contents
COSTWAY EP24962USA Jump Starter
Please give us a chance to make it right and do better！
Contact our friendly customer service department for help first. Replacements
for missing or damaged parts will be shipped ASAP!
BBefore You Startefore You Start
- Please read all instructions carefully.
- Retain instructions for future reference.
- Separate and count all parts and hardware.
- Read through each step carefully and follow the proper order.
- We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
- Always place the product on a flat, steady and stable surface.
- Keep all small parts and packaging materials for this product away from babies and children as they potentially pose a serious choking hazard.
SAFETY INSTRUCTIONS
Read the user instructions carefully before use. Save them for future reference.
WARNING:
- Wear safety glasses. Incorrect handling may cause a risk of personal injury if you get battery acid in your eyes, rinse your eyes with clean water for at least 10 minutes and then seek medical attention immediately.
- If the jump starter is handled wrongly, there is a risk of explosion and serious personal injury and/or material damage.
- When the jump starter is not in use, the black inverter power switch should be in the OFF position, to avoid the risk of personal injury and/or material damage if the clamps short-circuit.
- Never short-circuit the clamps with any metal object or by allowing them to touch each other.
- Check that the vehicle battery is 12V, or there will be a risk of explosion and/or serious injury.
- Before you start the jump starter, check that the clamps are connected with the right polarity, otherwise the device or the battery could explode and cause serious injury and/or material damage.
- CAUTION: The jump starter cannot be used to replace the vehicle’s own battery.
- Only use the built-in charger. Other chargers may shorten the lifetime of the battery or cause it to explode and cause personal injury or material damage.
TECHNICAL DATA
| Model | GM022IC |
|---|---|
| Voltage | 12V |
| Amps | 600A cranking amps（5s） |
| Battery type | Lead-acid battery 12V 22AH |
AC ADAPTOR
| ETL certificated
INPUT 120V AC, 60Hz, 0.25A OUTPUT 12V DC 1A
FEATURES
- Pressure gauge
- 12V outlet
- Emergency lighting
- Charging connection
- Indicator light for correct/incorrect connection
- Power switch for compressor/USB
- 5V USB connection
- Power switch
- Indicator light for correct/incorrect connection
- Indicator lights for charge level
- Battery control button/switch for emergency light
- Compressor compartment
- Inverter fuse
- Indicator light for inverter fault
- 120V outlets
- Indicator light for inverter
- Inverter power switch
OPERATION
INTENDED USE
- The jump starter is intended to start cars, boats etc. with 12V batteries.
- The jump starter has a 12V outlet which can be used to power most appliances that are designed to be connected to a 12V outlet (max. 15A).
- LED light for emergency lighting.
- 200W inverter to power appliances designed for 120V. Indicator lights for inverter status.
- The built-in battery in the jump starter can be charged with an external charger connected to the charging connection. The jump starter has a built-in overcharge protection.
- 5 V USB connection for charging mobile phones etc.
- Indicator lights showing battery level.
CHARGE THE JUMP STARTER BATTERY
NOTE:
- Charge the built-in battery in the jump starter before using it for the first time.
- Check the charge level in the built-in battery by pressing the battery control switch and reading the indicator lights. If the red indicator light comes on, the battery should be charged.
- Always keep the battery fully charged for best results and battery life. The battery capacity and lifetime will be affected if it is left discharged for a long time.
- Charge the built-in battery in the jump starter every three months if not used.
- The battery will last longer if you follow the instructions below.
- Charge the battery before using it for the first time.
- Charge the battery fully after each use.
- Charge the battery fully every 3 months.
- Connect the charger to a mains outlet.
- Connect the charger plug to the socket.
- The three indicator lights flash in turn to show that the built-in battery is being charged.
- It takes 6-40 hours to charge the built-in battery fully, depending on the condition of the battery.
- When the battery is fully charged, the green indicator light comes on. Allow charging to continue if possible, to prolong battery life.
- Disconnect the charger.
POWER SUPPLY VIA 12V OUTLET
NOTE:
- The outlet has overload protection with automatic reset.
- The internal battery in the jump starter can be emergency charged from the vehicle’s 12V outlet. However, it cannot be charged fully in this way. Use the AC charger in the usual case.
- Open the cover over the outlet.
- Connect the 12V product to the outlet.
JUMP STARTING OF ENGINE
WARNING:
- Make sure the vehicle battery is 12V, or there will be a risk of explosion and/or serious injury.
- Before you start the jump starter, make sure the clamps are connected with the right polarity.
- Follow the instructions below, otherwise there is a risk of personal injury and/or material damage.
- Switch off the ignition and all systems (lights, radio, air-conditioning etc.) in the vehicle.
- Connect the red positive clamp (+) on the jump starter firmly to the positive terminal (+) on the vehicle battery.
- Connect the black negative clamp (-) to the negative terminal (-) on the battery or to a metal part of the vehicle. If the connection is made correctly, the green light will come on.
- Put the switch in the ON position.
- Turn the ignition key to try to start the engine. Do not hold the key turned for more than 5 seconds.
- If the vehicle does not start, wait for at least 3 minutes and try again.
- If the engine starts, set the power switch to the OFF position.
- Disconnect the black negative cable (-) and put it away.
- Disconnect the red positive cable (+) and put it away.
- Recharge the built-in battery in the jump starter as soon as possible.
COMPRESSOR
WARNING: The compressor can be run continuously for maximum 10 minutes and then it needs to cool down for at least 10 minutes. When inflating tires, the pressure rise very quickly – pay attention.
Inflation
- Open the compressor compartment and pull out the air hose.
- Place the nozzle over the valve and press it right down. Fold down the locking lever into the locked position.
- Start the compressor with the compressor power switch.
- Monitor the air pressure on the manometer until the desired pressure is reached.
- When the desired pressure has been reached, turn off the compressor with the power switch, fold up the locking lever and disconnect the nozzle from the valve. Replace the hose in the compressor compartment.
- Use an adapter to inflate beach balls, air mattresses, inflatable boats etc.
INVERTER
- The inverter can supply 120VAC, 60Hz, 200W.
- To protect the battery, the inverter is fitted with under voltage protection. If the voltage falls too low, an alarm will be emitted and the inverter will be switched off. It will be reset automatically when the battery voltage is higher.
- The inverter is fitted with short-circuit protection, which switches off the jump starter if the connected equipment short-circuits.
- If the indicator light on the inverter comes on, check that the connected equipment is working correctly and does not need too much power for the jump starter. Also check the charge level in the battery.
- The fuse trips in the following situations. Replace the fuse if necessary.
- If the connected equipment needs too much power.
- In the event of a short circuit in the connected equipment.
- Set the inverter power switch to the ON position.
- Insert the cable from the external equipment into the 120V outlet.
- Start the external equipment.
- The inverter can be switched off automatically or with the power switch.
MAINTENANCE
REPLACING THE BATTERY
WARNING: Do not burn batteries — risk of explosion.
- Loosen the screws holding the back cover.
- Separate the front and back covers so the battery is visible.
- Remove the battery.
- Unscrew the positive and negative wires from the battery.
- Connect the red positive wire to the battery’s positive terminal and the black negative wire to the battery’s negative terminal.
- Place the new battery in the battery compartment.
- Replace the back cover and tighten the screws.
- Spent batteries must be disposed of in accordance with applicable regulations.
Care for the environment!
Must not be discarded with household waste! This product contains electrical
or electronic components that should be recycled. Leave the product for
recycling at the designated station e.g. the local authority’s recycling
station.
Welcome to visit our website and purchase our quality products!
With your inspiring rating, COSTWAY will be more consistent to offer you EASY
SHOPPING EXPERIENCE, GOOD PRODUCTS and
EFFICIENT SERVICE! US office: Fontana, California
UK office: Ipswich
We would like to extend our heartfelt thanks to all of our customers for taking time to assemble this product and giving us valuable feedbacks.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>