Shenzhen Yitming Lighting YM-WF-A60 Smart Bulb User Manual

Shenzhen Yitming Lighting YM-WF-A60 Smart Bulb

Safety Warning

• This device is for indoor use only.
• This device should not be exposed to dripping or splashing water or any dangerous sources.
• This device should only be installed by adults.
• Do not install near any heat sources.
• Do not use this device with dimmers.
• Do not use this device in totally enclosed luminaires. Use this device in open luminaires only.
• If this device is much heavier than the one to be replaced, the increased weight may reduce the mechanical stability of certain luminaires and lampholders and may I’m pair contact making and lamp retention.
• RISK OF ELECTRIC SHOCK: USE IN DRY LOCATIONS ONLY. Do not install this device with wet hands.

What You Need for Wi-Fi Setup

• Smart
• A smart phone
• A router (Supports 2.4

Install the app “Smart Life-Smart Living”

You may find the APP-“Smart Life-Smart Living” on Apple App store, Google Play, or Scan the QR code below and install it.

The free app “Smart Life-Smart Living” is compatible with mobile devices that support iOS 8.0 above, Android 4.4 above.

Connecting Your Bulb to a Wi-Fi Network

Follow the on-screen instructions to register and login to set your smart home.

Easy Mode (Recommend)

1. Disconnect the power supply and install the lamp.

2. Turn on the power supply and you can see the bright white light flashing( twice in a second). If not, cut off the power supply and then power it on three times.

3. Open the “Smart Life” APP, tap the
   “ADD DEVICES” or the “+” at the upper right corner of the page, choose “ALL” and then select “Lighting Devices”.

4. Make sure the light is flashing twice per second and confirm it in the app.

5. Choose your local WIFI and input the correct password.(The device only supports 2.4 Ghz wifi)

6. 6. Wait for configuring successfully, then tap “Done”.

APMode

1. Please change to “AP Mode” if conn -ecting failed in “Easy Mode”. The AP Mode is at the upper right corner of the “ADD DEVICE” page.
2. Turn the power off and on 3 times to make it flash slowly and them confirm it in the App.
3. Choose the local WIFI and enter the correct password.
4. Tap ” Connect Now”, choose WIFI hot -spot named “Smartlife-XXXX”, go back to “Smart Life” app.
5. Wait for configuring successfully, then tap “Done”.

Note : There ore two f/oshing modes, fast and slow. Turn the power off and on 3 times can change the flashing mode.

Control Your Smart Bulb in APP

Nate : The instructions in this manual are for your reference only. The opp will be updated from time to time. Always follow the instructions in the opp to complete Wi-Fi setup and know more about the functions.

Control Your Smart Bulb with Alexa/ Google Assistant

Before you start, make sure that:

• Your smart bulb is connected with wifi and can be controlled by app.
• You have an Alexa-enabled device (i.e. Echo, Echo Dot and Amazon Tap) or a device enabled with Google Assistant (i.e. Google Home).
• The Amazon Alexa app or the Google Home app which is already installed on your smart device and you have created an account.

To control your devices with Amazon Alexa:

1. Open the Alexa app and select Skills from the menu in the top left corner of the homepage.
2. On the Skills screen, search for “Smart Life”.
3. Enable it in the Alexa app.
4. log in with your Smart Life account to authorize Alexa to access to your account.
5. Discover new smart devices via the “Smart Home” menu in the Alexa app or Alexa voice control.
6. Say simple commands to Alexa.

To control your devices with Google Assistant:

1. Open the Google Home app and select “Home Control” in the menu.
2. Tap the”+” icon in the Device list and then select “Smart Life”.
3. Follow the instructions in the Google Home app to authorize the Google Assistant with your “Smart life” account.
4. After successful configuration, say sim-pie commands to Google Assistant to control the light with your voice.

Troubleshooting

Cannot connect to Wi-Fi

• Check if you have selected a 2.4 Ghz wifi which is the same that your phone is connected with. (If your router is dual band, make sure your phone and the smart bulb are connected to the 2.4 G signal.)
• Check if you have entered the correct Wi­Fi password.
• Check if there are any internet problems. If necessary, reset your Wi-Fi router and try again.

Cannot control the devices with Alexa/Google voice control

• Check if there are any internet problems.
• Check if you have enabled “Smart Life” in Alexa or Google APP.
• • Check if you are using proper commands when talking to Alexa/ Google Assistant, repeat your question, speak clearly to Alexa/ Google Assistant in English.
• Check if you have modified the name of the bulb in the “Smart Life-Smart living” app. If yes, you need to rediscover the devices through Alexa/ Google app.

Notice:

• Please check if there is damage caused by transportation. If broken, please contact the supplier for replacement.
• Please follow the instruction and notice to keep the product in a good and safe use condition.
• Do not disassemble or reinstall the bulb.

Customer Service

• 12-month limited warranty
• Lifetime technical support
• service@szpuji.com

For any inquiries or comments concerning this product, please do not hesitate to contact the seller. We appreciate your support!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>