EK Quantum Reflection PC-O11D EVO D5 PWM D-RGB User Guide
- October 27, 2023
- quantum
Table of Contents
- BOX CONTENTS
- DISTRIBUTION PLATE DIMENSIONS
- TECHNICAL SPECIFICATIONS AND PRODUCT PARTS
- PREPARING THE 011D EVO CHASSIS
- PREPARING AND INSTALLING THE DISTRIBUTION PLATE
- RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS
- ATTACHING THE PUSH-IN ADAPTER (OPTIONAL)
- FLOW DIAGRAM
- CONNECTING THE D-RGB LED STRIP
- CONNECTING THE PUMP
- TESTING THE LOOP
- SUPPORT AND SERVICE
- SOCIAL MEDIA
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
EK Quantum Reflection PC-O11D EVO D5 PWM D-RGB
Please note the installation of the product is intended to be underaken by an adequately trained and experienced person. You are installing the product at your own risk. If you are not properly trained or experienced or feel unsure about the installation procedure, please refrain from installing the product yourself and contact our tech support for assistance. We disclaim our liability for any damages to the product as well as incidental, consequential, or indirect damages incurred due to improper or inappropriate installation
Before you start using this product please follow these basic guidelines:
Please carefully read the manual before beginning with the installation
process!
The EK Fittings require only a small amount of force to screw them firmly
in place since the liquid seal is ensured by the rubber O-ring gaskets.
The use of corrosion inhibiting coolants is always recommended for
any liquid cooling system. EKWB recommends any of the EKCryofuel for worry-
free usage.
BOX CONTENTS
EK-Quantum Reflection2 PC-O11D EVO D5 PWM D-RGB
|
EK-Loop Multi Allen Key (1 pc)
---|---
Screw M4x8 DIN7991 (2 pcs)
|
Screw M3x8 DIN7991 (2 pcs)
Allen Key 2.5 mm (1 pc)
|
Allen Key 2 mm (1 pc)
DISTRIBUTION PLATE DIMENSIONS
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS
Technical Specification:
Dimensions with the attached pump (W x D x H): 207.3 x 75.4 x 405.2 mm
- D-RGB LED count: 21
- D-RGB cable length: 500 mm
- D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground)
Position | EAN | Description | Quantity |
---|---|---|---|
1 | 104705 | TOP Plexi (Block part) | 1 |
2 | 104706 | TOP Plexi (Lid part) | 1 |
3 | 3831109837597 | EK D5 Pump | 1 |
4 | 101803 | Pump holder | 1 |
5 | 104709 | LED Cover (Black e.) | 1 |
6 | 100663 | EK – Badge | 2 |
7 | 8206 | Screw M4 x 12 DIN7991 | 65 |
8 | 8204 | Screw M3 x 20 DIN7991 | 4 |
9 | 9017 | Screw M4 x 20 DIN7984 | 4 |
10 | 104599 | Mylar sticker | 2 |
11 | 5154 | OR – 52 x 3 NBR50 | 1 |
12 | 104716 | OR – 397 x 2 mm | 1 |
13 | 104717 | OR – 57 x 2 mm | 1 |
14 | 104718 | OR – 113 x 2 mm | 1 |
15 | 104719 | OR – 94 x 2 mm | 1 |
16 | 104720 | OR – 102 x 2 mm | 1 |
17 | 104721 | OR – 128 x 2 mm | 1 |
18 | 104722 | OR – 108 x 2 mm | 1 |
19 | 3831109895313 | Push-in adapter | 4 |
20 | 102639 | EK – Plug G1/4 | 13 |
21 | 3831109834282 | Plug cover (Acetal) | 13 |
22 | 102458 | LED D-RGB strip 800/600 mm | 1 |
PREPARING THE 011D EVO CHASSIS
STEP 1
Unscrew the factory provided screws and remove the top panels from the case.
STEP 2
Remove both side panels and the front panel from the case.
PREPARING AND INSTALLING THE DISTRIBUTION PLATE
STEP 1
Carefully place the distribution plate into the case and align the mounting
holes. Be careful not to scratch the acrylic!
STEP 2
Secure the distribution plate using the included M3 x 8 and M4 x 8 DIN7991
screws through the front frame of the case. The screws shouldn’t be over-
tightened to avoid cracking the plexi. The screw heads should sink in as not
to interfere with the mounted front panel.
For this step you will need:
Allen Key 2 mm
|
Allen Key 2.5 mm
---|---
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS
To complete your loop, all ports must be used as marked in the image.
All remaining unused ports must be closed with supplied plugs, using the EK-
Loop Multi Allen Key
| If one of the prescribed components will not be installed (ie. bottom
radiator or GPU block) then one INLET and one OUTLET port must still be joined
together in order for this distribution plate to function!
---|---
| Note that the side radiator is completely optional and a loop without the
side radiator can be completed without joining the two side radiator ports.
---|---
| Only one INLET and one OUTLET port for the GPU connection can be used, while
all other INLET and OUTLET GPU ports must be closed with G1/4 plugs (enclosed
in the package).
---|---
| The distribution plate is designed to function in both regular and inverted
case configurations. Inverting the case does not change the port
configuration.
---|---
ATTACHING THE PUSH-IN ADAPTER (OPTIONAL)
The push-in adapters can be attached to the marked places in the diagram.
For easier installation of the push-in adapters, EK recommends to lubricate
the O-rings with a few drops of coolant or water.
FLOW DIAGRAM
CONNECTING THE D-RGB LED STRIP
Plug the 3-pin connector of the distribution plate D-RGB LED light to the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, Empty, Ground.
CONNECTING THE PUMP
The EK-D5 PWM pump has two connectors.
- SATA Connector: It must be connected directly to your PSU at all times as it is used to power the pump.
- 4-pin PWM fan: It can be connected to your motherboard’s CPU_ Fan or designated water pump header. It can also be connected to a controller. This cable is used to control and report the rotational speed of the pump. If it’s not connected, the pump will run at maximum speed (100% PWM)
TESTING THE LOOP
To make sure the installation of EK components was successful, we recommend
you perform a leak test for 24 hours.
When your loop is complete and filled with coolant, connect the pump to a PSU
outside of your system. Do not connect power to any of the other components.
Turn on the PSU and let the pumprun continuously. It is normal for the coolant
level to drop during this process as air collects in the distribution plate.
Inspect all parts of the loop, and in the eventuality that coolant leaks, fix
the issue and repeat the testing process. Ensure that all hardware is dry
before the system is powered on in order to prevent any damage.
SUPPORT AND SERVICE
In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND PRODUCT PARTS” where you can find the EAN number of each part you might need.
Include the EAN number with quantity in your request. Mounting
Mechanism EAN can be found under “BOX CONTENTS”
Thermal pads are readily available in the EK shop
SOCIAL MEDIA
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
EKWBofficial
ekwaterblocks
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>