ORLACO 0300150 WISR Long Range Installation Guide
- June 6, 2024
- ORLACO
Table of Contents
0300150 WISR Long Range
Installation Guide
Installation manual No. IM0973673 A 01
Art. No: 0300150
09/2020
Installation manual
WISR Long Range, Art. No. 0300150
Safety
In order to guarantee safe operation, these safety instructions must be read
before you start using this equipment.
- Do not open the enclosure. This can cause damage, shortcircuiting or electrical shocks.
- Do not expose the equipment to extreme temperatures, this can cause deformation of the enclosure or damage to internal components.
- Repairs may only be undertaken by Orlaco.
- The equipment must be assembled as shown in this manual.
- If there have been alterations or changes to this equipment that have not been specifically approved by Orlaco, use of this equipment is not permitted.
- Warning! RF radiation. This device is using Radio Frequency (RF) signals to establish a wireless video link. Keep a minimum separation distance of 0.2m between the WISR long-range and the human body to comply with the regulation regarding human exposure to RF radiation.
Preface
Only connect this product to a SELV (Separated or Safety Extra-Low Voltage) or
a double insulated power source. Ensure that a fuse 2A T has been installed in
the power line of the WISR Long Range Before you start using this equipment,
please read this manual carefully and follow all instructions. This
installation manual describes the functions of the equipment, outlines the
connection options, and explains how to put the equipment into operation. We
recommend that you keep this manual in a safe place for reference purposes.
If you have any questions or issues concerning the operation of this
equipment, consult the relevant section in the manual or contact the Orlaco
Products BV Service department.
All data is subject to change without notice. All dimensions are for
commercial purposes only. The Orlaco products comply with the latest CE, ADR,
EMC, and mirror-directive regulations, where applicable. All products are
manufactured in accordance with the ISO 9001 quality management system, IATF
16949 quality automotive, ISO 14001 environmental management systems, where
applicable.
Introduction
The WISR Long Range system provides a Wi-Fi® connection within a view system.
The WISR Long Range router is both a receiver and a transmitter. This document
describes WISR Long Range system installation.
List of abbreviations
IP(-address) Internet Protocol (Address). Unique address inside a network.
MAC (-address) Media Access Control Address. A worldwide unique address for
Ethernet devices.
ROI Region Of Interest. Used to specify resolution or crops of the video
image.
WISR Wireless Sender Reciever.
IMPORTANT
Avoid mounting the WISR Long Range with connectors faced up. Preferably
mounting the WISR Long Range with connectors facing down.
Installation manual
Application possibilities of the WISR Long Range system, figure. 1.
2 camera system
4 camera system 2. Configuration
To create a Wi-Fi® connection, there must always be a WISR Long Range router
in the system. In a 2 camera system, one WISR Long Range router is connected
with the tablet. For the 4 camera system, a second WISR Long Range router set
communicates with the other WISR Long Range router within a work zone. Figure
1 shows two systems using one or two wires. To connect two cameras with the
WISR Long Range, an extension cable must be used; This cable must be ordered
separately, check with Orlaco.
Cable Uni Ethernet
1m; Art. No. 0321000 9m; Art. No. 0321060
2m; Art. No. 0321010 11m; Art. No. 0321070
3m; Art. No. 0321020 16m; Art. No. 0321080
5m; Art. No. 0321030 21m; Art. No. 0321090
7,5m; Art. No. 0321040 40m; Art. No. 0321100
8m; Art. No. 0321050
Optionally, a holder for the tablet is available.
See figure 2. Tablet holder 8.5″ to 11.125″. Article No. 2015880.
See Datasheet: DS0963137.
IMPORTANT: A tablet charging adapter is not included
3. Operation
The WISR Long Range works together with the Android app `PhotonView’. WISR
Long Range firmware can be updated via Wi-Fi® with the tablet (Android Photon
View app) with a Wi-Fi® connection. (Check with Orlaco to receive the
software). The Wi-Fi® antenna has an omnidirectional orientation. Typically
the system will cover XXL. The maximum range is XXm, measured under optimal
conditions in the open field. Local interference metal objects and weather
conditions can cause the maximum range to decrease.
4. Assembly / Installation
4.1 Options
The WISR Long Range system can be mounted in various ways. Depending on the
use, there are various mounting options for the WISR Long Range system.
IMPORTANT The best reception of the signal on the tablet can be
obtained by placing the tablet and the WISR Long Range so that there is as
little as possible metal between them.
IMPORTANT Avoid mounting the WISR Long Range with connectors faced up.
Preferably mounting the WISR Long Range with connectors facing down.
4.2 Connections
Connecting the WISR Long Range system is easy. Connect the tablet to the
WISR Long Range router and the Cameras using the PhotonView app. The detailed
user instructions are listed in the User Manual UM0972260. Connect the camera
video cables to the 4p connections on the WISR Long Range router and the power
cable with the 8p connector on the WISR Long Range router for the supply
voltage.
4.3 The photonView app
The detailed user instructions are listed in the User Manual UM0972260.
Dimensions
See figure 3.
Technical specifications
**General
**
Description: Wireless Send Receive (WISR Long Range).
Software: The WISR Long Range works together with the Android app
`PhotonView’.
Firmware: The WISR Long Range firmware can be updated via Wi-Fi® with the
tablet (Android Photon View app).
Weight: 0,30kg.
Operating temperature: -40ºC to +85ºC.
Radio Antenna type : 2x Internal Right Hand Circular Polarized antennas
with MIMO technics.
Antenna orientation : Directional antenna, 90 Degrees.
Frequency range: Ch 1-13 (2412-2472 MHz) depending on national
requirements. Max.
Transmitting power: 1-26 dBm E.I.R.P. Depending on national requirements.
Maximum range: 200m open field with the wired monitor. Local
interference, metal object, and weather conditions will shorten the maximum
distance.
Electrical Rated voltage range : 9-32V/DC.
Rated power : 5W max.
Switch Inputs : 4 Camera selection inputs plus
Handbrake and Tacho inputs 0-30V, 0-8V (low) / 8-30V (high).
Power cable: 2m M12F8 ow/Ferret (Art. No. 0300011).
Mechanical
Enclosure; Automotive thermoplastic polymer (33% glass filled).
Shock resistance: 15,3Grms, 5 to 2000, PSD.
Dust and water protection: IP67 according to IEC 60529; dust-tight and
protected against the effects of continuous immersion in water up to 1m for 30
minutes. IP69k according to DIN 40050-9: WISR can withstand a high-pressure
cleaning with water: 14-16L/min. 80°C and 100 bars flow.
Operating temperature -40°C…+85°C.
Certification Approvals: CE, Regulation 10 FCC, IC. CE EMC environments
to be used: On-road trucks, off-road trucks, maritime, railway, industrial
trucks.
7. Electrical connections
See figure 4.
8. Maintenance and cleaning
Clean this product with a damp cloth. Do not use aggressive chemicals or
abrasive cleaning agents.
9. FCC Statement
15.21 Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
Either (§15.105) class B device
The equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
manufacturer’s instructions, may cause interference harmful to radio
communications. There is no guarantee, however, that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
consult the dealer or an experienced radio or TV technician for help.
10. IC Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device
Caution: Exposure to Radio Frequency Radiation. To comply with RSS 102 RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
11. Disposal
Disassembly, removal, and disposal. Local regulations for dealing with waste must be followed when disposing of disassembled components or entire units.
12. General terms and conditions
Orlaco Products BV is not liable for damage resulting from inadequate servicing, incorrect usage, or alterations made to the equipment without informing the manufacturer in writing.
This installation manual has been made available by Orlaco Products BV. All rights reserved. No part of this manual may be reproduced and/or made public in printed form, in photocopy form or on microfilm, or in any other way, without the prior written permission of Orlaco. This also applies to the associated drawings and figures.
Orlaco reserves the right to make changes to components at any time without informing customers beforehand or directly. All dimensions given are for commercial purposes.
For information regarding repairs that is not covered in this manual, please contact the Orlaco Products BV service department.
This manual has been prepared with all due care and attention. However, Orlaco Products BV cannot be held responsible for any errors in this manual or any consequences thereof.
For additional technical information please contact the Orlaco Products BV Service department.
13. Release notes
Version A 01 First issue September 2020.
ORLACO
Orlaco is a Manufacturing company that specializes in making cameras and monitor systems for commercial vehicles, fork-lift trucks, cranes, offshore and maritime. Our objective is to design and produce camera systems for the professional market that improve the drivers’ view and increase operating efficiency.
At our facility in Barneveld, we locate our design, manufacturing, warehousing, and service department. Vision is our mission®. Orlaco, therefore, deploys the development, manufacture, supply, and service of camera and display systems that will improve the safety and efficiency of all vehicles, machinery, and vessels. Our systems give the end-user a view of each blind spot and will create comfort and improved working conditions. Our active approach will support market demands and innovations and will lead to enthusiastic ambassadors in the market; our customers. For more information: www.orlaco.com
Available documentation https://www.orlaco.com/downloads
User manual: UM0972260 WISR
Datasheet: DS0963572-0300150 WISR
Long Range DS0961110-0186000
Camera EMOS Ethernet
Package – WISR
Long Range router – Power cable 2m
WISR Long Range system article numbers: 0300150 WISR
Long Range 0290000 Tablet 0186010
Camera EMOS 120° Ethernet 0300011 Power cable